APC RBC24 UPS Battery Replacement Cartridge Instruction Manual

1. Introduction and Overview

This manual provides essential information for the safe and effective use of your APC Replacement Battery Cartridge (RBC24). The RBC24 is specifically designed to restore the performance of compatible APC Uninterruptible Power Supply (UPS) units to their original specifications. This cartridge is a Valve Regulated Lead-Acid (VRLA) battery.

For optimal performance and to maintain your APC UPS warranty, use only genuine APC replacement batteries.

2. Safety Information

Observe the following safety precautions when handling and installing the battery cartridge:

• Do not charge the battery in a gas-tight container.
• Do not short battery terminals.
• Do not incinerate the battery.
• In case of contact with electrolyte (acid), flush immediately with water.
• This is a sealed, non-spillable lead-acid battery. It must be recycled properly.

Always refer to your specific UPS unit's user manual for additional safety guidelines and battery replacement procedures.

Image 2.1: Battery label showing safety warnings and recycling information.

3. Compatibility

The APC RBC24 Replacement Battery Cartridge is compatible with various APC Smart-UPS models, including but not limited to:

• SMT1500RM2US
• SMT1500R2-NMC
• SU1400RM2U
• SU1400RMNET
• SUA1500RM2U

Always verify the compatibility with your specific UPS model before installation.

4. Package Contents

Your APC RBC24 package typically includes:

• One (1) APC RBC24 Replacement Battery Cartridge
• Necessary cables and fuses for installation (pre-attached or included)

Image 4.1: The APC RBC24 Replacement Battery Cartridge.

5. Setup and Installation

Follow these general steps to replace the battery cartridge in your compatible APC UPS. Refer to your specific UPS model's user manual for detailed instructions and safety warnings.

1. Power Down the UPS: Completely shut down your UPS and any connected equipment. Disconnect the UPS from the AC power outlet.
2. Disconnect Internal Battery: Locate the battery access panel on your UPS. Open the panel and disconnect the internal battery connector.
3. Remove Old Battery: Carefully slide the old RBC24 cartridge out of the UPS bay. Note its orientation for correct installation of the new cartridge.
4. Insert New Battery: Slide the new APC RBC24 cartridge into the UPS bay, ensuring it is correctly oriented and fully seated.
5. Connect New Battery: Connect the battery connector of the new RBC24 to the UPS. Ensure a secure connection.
6. Close Access Panel: Securely close the battery access panel.
7. Restore Power: Reconnect the UPS to the AC power outlet. The UPS may perform a self-test. Power on your connected equipment.

Image 5.1: Side view of the APC RBC24, illustrating its form factor for installation.

After installation, allow the new battery to charge for at least 24 hours to reach full capacity before relying on it for extended runtime.

6. Operating Instructions

Once installed and fully charged, the RBC24 operates automatically as part of your UPS system. The UPS will manage charging and discharge cycles. Monitor your UPS status indicators for battery health and runtime information.

7. Maintenance

The RBC24 is a maintenance-free battery. However, proper disposal is crucial for environmental protection.

Battery Recycling

APC offers an "RBC Recycling Program" for environmentally responsible disposal of your old UPS battery. This program typically includes free return to a recycling center. You can often use the packaging from your new battery to return the old one. Visit the official APC website for details on how to participate in this program.

8. Troubleshooting

If your UPS does not function correctly after installing the new RBC24, consider the following:

• Check Connections: Ensure all battery connectors are securely seated.
• Verify UPS Power: Confirm the UPS is connected to a live AC power outlet.
• Initial Charge: Allow sufficient time (at least 24 hours) for the battery to fully charge.
• Consult UPS Manual: Refer to your specific UPS model's user manual for troubleshooting steps related to battery errors or power issues.
• Contact Support: If issues persist, contact APC customer support for assistance.

9. Specifications

10. Warranty and Support

Genuine APC Batteries are backed by a 2-year Manufacturer Warranty. For warranty claims or technical support, please visit the official APC website or contact their customer service department. Ensure you retain your proof of purchase.

For information regarding the APC RBC Recycling Program, please visit www.apc.com.