apex logo

SET INBOUND/OUTBOUND VOLUMES

  • After login in, press the Volume iconAPEX Set Inbound Outbound Volumes - Volume icon
  • To enable/disable nighttime outbound volume press to enable or disable. Then select the time to start and stop.APEX Set Inbound Outbound Volumes - enable Note: This reduces outbound audio by 20%
  • Adjusting kitchen speaker volume for Lane 1 or Lane 2APEX Set Inbound Outbound Volumes - speakerNote: Press the circle and slide left or right to the appropriate volume level
  • Adjusting the outbound speaker for Lane 1 or Lane 2APEX Set Inbound Outbound Volumes - microphponeNote: Press the circle and slide left or right to the appropriate volume level
  • Adjusting the inbound microphone for Lane 1 or Lane 2APEX Set Inbound Outbound Volumes - microphpone 1Note: Press the circle and slide left or right to the appropriate volume level

NOISE SUPPRESSION

  • After logging in, press the Audio iconAPEX Set Inbound Outbound Volumes - audio icon
  • Adjust the amount of Noise Suppression for the outside speakerAPEX Set Inbound Outbound Volumes - speaker 1Note: Press the circle and slide left or right to adjust to proper settings
  • Adjust the amount of Noise Suppression on the inbound microphoneAPEX Set Inbound Outbound Volumes - microphpone 2Note: Press the circle and slide left or right to adjust to proper settings
  • Extended sitting and Echo cancellationAPEX Set Inbound Outbound Volumes - setting
    Note: Please call support at 800.598.2370 when adjusting these settings

LANE SETTINGS

  • After logging in, press the Lane iconAPEX Set Inbound Outbound Volumes - lane icon
  • Singl LaneAPEX Set Inbound Outbound Volumes - single laneSet Speed Team and Override Lane 1APEX Set Inbound Outbound Volumes - override lane
  • Dual Lane ConfigurationAPEX Set Inbound Outbound Volumes - dual laneNote: Headsets will need to be either Team 1 or Team 2
  • Speed Team or Vehicle OverrideAPEX Set Inbound Outbound Volumes - override lane 1Note: Press the slider to turn on Speed Team for Lane 1 or Lane 2. Press the slider to turn on Vehicle Override for Lane 1 or Lane 2

MANAGER

  • After logging in, press the Manager iconAPEX Set Inbound Outbound Volumes - manager icon
  • Set the time and change the manager passwordAPEX Set Inbound Outbound Volumes - manager passwordNote: Follow the onscreen prompts to change time and the manager’s password

IMPORT/EXPORT AND ENGINEER SETTINGS

APEX Set Inbound Outbound Volumes - engineer

Note: Call R.F. Technologies, Inc. at 800.598.2370 to get into these settings.

HELP ICON

APEX Set Inbound Outbound Volumes - hlep icon

Note: For questions on how to:

  • Set Alerts
  • Set Reminders
  • Set Greeters
  • Set Volumes
  • Register Headsets
  • Select a Lane Type

FCC Regulation

Headset
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense

Base Station
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device contains license-exempt transmitter(s)/receiver(s) that comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation of the device.
In order to comply with FCC and IC RF Exposure requirements, the base must be installed and operated such that a minimum separation distance of 20 cm is maintained between the base and all persons during normal operation
Changes or modifications not expressly approved by R.F. Technologies, Inc. could void the user’s authority to operate this equipment.

Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s)]. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

apex logo

Ready for APEX to provide your customers with their best drive-thru experience?
Contact us today.
rfdrivethru.com|800-598-2370|[email protected]

Documents / Resources

APEX Set Inbound/Outbound Volumes [pdf] User Guide
APXBA, TOMAPXBA, APXHS, TOMAPXHS, Set Inbound Outbound Volumes

Leave a comment

Your email address will not be published.