Assembly Guide
Included Parts
Hardware
Step 1: Attach Outer Legs
Before you begin, be sure that you’re assembling on a non-abrasive surface, such as carpet or flattened cardboard.
With the Primary Slide Assembly placed upside down position a Outer Leg in one of the corners.
Line up the holes on the cross brace to the threaded holes in the Outer Leg.
On one of the long screws place a locking washer first followed by a flat washer. Place the screw through the cross brace on the Primary Slide Assembly and into the outer leg and loosely tighten, repeat with the second screw.
Once both screws have been inserted and hand tightened you can use a M5 Allen Key to tighten fully.
NOTE: be careful not to overtighten as this could damage the wood.
Repeat with the other three Outer Legs.
Step 2: Assemble the Middle Leg Support
With a helper, turn the table over onto its legs.
Once the table is upright you can undo the latches holding the two sides together and extend the table.
Next attach the middle leg support to a middle leg.
NOTE: the top of the middle leg has the threaded insert and the bottom has a floor protector.
The middle leg support uses a slotted keyway and dowel slot to attach to the screw and dowel on the side of the middle leg. The larger side of the keyway should face down to allow the support to seat on the leg. Slide the screw into the slotted keyway. Repeat with the other Middle Leg to create an “H” configuration.
Step 3: Attach the Middle Leg Support
Next place the Middle Leg under one of the wood stringers on the extended table.
Line up the holes on the stringer with the threaded holes on the middle leg assembly. Place one of the small screws through a hole in the stringer and into the threaded hole on the middle leg and loosely tighten, repeat with the second screw.
Once both screws have been inserted and hand tightened you can use a M4 Allen Key to tighten fully.
Repeat with the other middle leg assembly.
IF YOU ARE USING
| 0-1 Leaves | No Middle Support Legs Required |
| 2-3 Leaves | 1 Middle Support Leg Required |
| 4-6 Leaves | 2 Middle Support Legs Required |
Step 4: Insert Extendable Leaves
Place one of the extendable leaves on the extended table. Line up the dowels on the leaf with the dowel holes on the table. Push the leaf into the holes on the table.
Repeat with additional leaves to achieve the desired table size. Once you have placed the final leaf, push the other side of the table in to the last leaf to close the remaining gap.
Once all the leaves have been placed, reach under the leaf connection and affix the latch that connects each leaf together and the leaves to the slide assembly. Repeat for all remaining latches. The table is now complete.
NOTE: You can adjust the tension on the latch by rotating the loop in or out to reach desired tension.
Parts Diagram
| Item # | Part Name | Part Number | Qty |
| 1 | Primary Slide Assembly – Oak | FTP – 507 | 1 |
| 1 | Primary Slide Assembly – Walnut | FTP – 508 | 1 |
| 2 | Extendable Leaf – Oak | FTP – 509 | 6 |
| 2 | Extendable Leaf – Walnut | FTP – 510 | 6 |
| 3 | Outer Leg – Oak | FTP – 511 | 4 |
| 3 | Outer Leg – Walnut | FTP – 512 | 4 |
| 4 | Middle Leg – Oak | FTP – 513 | 4 |
| 4 | Middle Leg – Walnut | FTP – 514 | 4 |
| 5 | Middle Leg Support – Oak | FTP – 515 | 2 |
| 5 | Middle Leg Support – Walnut | FTP – 516 | 2 |
| 6 | Flex Table Hardware Pack | FTP – 506 | 1 |
For video assembly guide, scan the QR code: or visit: assembly.anabei.com
https://bit.ly/4aQi2xk?r=qr
Documents / Resources
 |
ANABEI Extendable Dining Table [pdf] Installation Guide Extendable Dining Table, Dining Table |