ASEC16WPC Ambius Security and Sensor Lights
“
Specifications:
- Model: ASEC16WPC Q5080635 & ASEC16WPCB Q5080645
- Fully adjustable heads
- Light Specifications:
- 3K-1300LM
- 4K-1500LM
- 5.7K-1400LM
- Time Adjustment: Adjustable 10 seconds to 15 minutes
Product Usage Instructions:
Ceiling Mount Installation:
1. Securely mount the base plate to the ceiling.
2. Adjust each head independently for optimum light
performance.
Wall Mount Installation:
1. Securely mount the base plate to the wall.
2. Adjust each head independently for optimum light
performance.
Safety Warning:
Always follow safety precautions mentioned in the manual during
installation and use.
Testing:
Follow the testing procedure mentioned in the manual to ensure
proper functionality.
Care and Cleaning:
Use a damp cloth to clean the exterior of the product. Do not
immerse in water.
Warranty Information:
Your product is warranted against faults and manufacturing
defects for 3 years under normal domestic use.
Frequently Asked Questions (FAQ):
Q: What should I do if my product fails to operate
satisfactorily?
A: Please return it to the retailer with proof of purchase for
repair or replacement within the warranty period.
Q: How do I adjust the time settings on the ceiling mount?
A: Use the adjustable dial to set the time between 10 seconds to
15 minutes for optimal functionality.
Q: Can I adjust the brightness of the lights?
A: Yes, each head can be independently adjusted to achieve the
desired light performance.
“`
CEILING MOUNT
Installation Guide & Owner Manual
AMBIUS SECURITY AND SENSOR LIGHTS
MODELS: ASEC16WPC Q5080635 & ASEC16WPCB Q5080645
FULLY ADJUSTABLE HEADS
Each Head can be independently adjusted to get the optimum light performance where you require
WALL MOUNT
LIGHT SPECIFICATIONS
· 16W (2x 8W) · Colour Temperature/ Lumens:
3K-1300LM / 4K -1500LM /
5.7K -1400LM
· Non Dimmable · Power/Lumen Adjustable · 90° Beam Angle · 6-8m Detection range · 150° Detection Angle · 3/ 30/ 300/ 2000 LUX Adjustment · Time Adjustment: 10sec – 15min · Easy mount base plate · Material: PC · Estimated Life:LM80 35,000hrs · 220-240V 50/60Hz.
CEILING MOUNT
TIME ADJUSTMENT: Adjustable 10 seconds to 15 Minutes. For convenience we have indicated approx. 5 & 9 minute positions.
POWER ADJUSTMENT: Use the Centre dial marked DIM. There are 4 power positions. 16watts / 12watts / 8 watts / 4 watts The highest 16W is marked `+’ The lowest which is 4W is marked `’ The other two marking are 8 & 12watts
LUX ADJUSTMENT: To operate in daylight, position at the mark `+’. To operate at Night position at the mark `’ (3 lux) The other 2 positions are for low light as indicated (approx. 30 & 300 lux)
SETTINGS
WALL MOUNT
INSTALLATION
· Ensure the power is turned off. · Unscrew the retention screws on the front and remove the
base plate.
· Feed the connection through the aperture provided. · Vertical Installation: arrow on base plate points upwards. · Horizontal Installation: arrow will point opposite way to
sensor/lights.
· Fix the base plate to the wall using the screw holes. · Connect power source to the “N” (blue wire) “L” (brown wire) according to the wiring diagram. · Choose your desired colour temperature by moving switch to either 3K/4K/5.5K · Now the light simply plugs back into base by lining up arrow and 3-Pins with terminal. See Fig 1. · Turn on the power.
Fig 1.
SAFETY WARNING
· Always read the instructions carefully before installation, failure to do this could result in damage to the product, property or harm to the installer. · This product must be installed by a licensed electrician in accordance with the Australian / New Zealand Wiring Rules AS/NZS 3000.
TEST
When testing daylight, set the TIME dial to show the “-” symbol and the LUX dial to show the “+” sun symbol. After 30 seconds the sensor should respond to presence and turn on and then off after the set 10 seconds. To set the sensor for the nighttime during the day turn the LUX dial towards the moon “-” symbol and cover the sensor face to simulate darkness.
CARE AND CLEANING
To clean wipe exterior with a damp cloth. Do not immerse in water.
PROOF OF PURCHASE
Please retain your purchase receipt for all warranty claims
WARRANTY
Your product is warranted against faults and manufacture when used in normal domestic use for a period of 3 years.
We undertake to replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period. This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone other than a qualified electrical service technician.
If your product fails to operate satisfactorily, please return it to the retailer from whom it was purchased to obtain a repair or replacement product. You will need to produce satisfactory evidence of date of purchase. If the product is to be replaced (cannot be repaired) then that replacement will be of the same or similar product or accessory excluding packaging, instruction card etc.
In New Zealand product is covered by the Consumers Guarantee Act (1993). In accordance with the act consumers are advised that: The manufacturer does not undertake that repair facilities and parts are necessarily available for this product.
New Zealand PO Box 100-707 N.S.M.C Auckland
Phone +64 (0)9 917 4000 Phone 0800 232 633 info@cdb.co.nz
Australia PO Box 574 South Morang Victoria, 3752
Phone +61 (0)3 9336 4423 Phone 1300 465 324
info@cdbgoldair.com.au
Documents / Resources
 |
AMBIUS ASEC16WPC Ambius Security and Sensor Lights [pdf] Installation Guide ASEC16WPC, ASEC16WPCB, ASEC16WPC Ambius Security and Sensor Lights, ASEC16WPC, Ambius Security and Sensor Lights, Security and Sensor Lights, Sensor Lights |