Altronix T3SSK75F28 28 Door Kit with Fused Outputs

Overview

Altronix T3SSK75F28 and T3SSK75F28D Trove S2 kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and sub-assemblies. Both kits accommodate Lenel-S2 (S2 Security Platform) S2-INST Installation Kit for S2 Network Node for up to twenty-eight (28) (T2SSK7F8) doors in a single enclosure.

Configuration Chart

Altronix Model Number

120VAC 60Hz Input Current A

Power Supply Board Input Fuse Rating

Power Supply Board Battery Fuse Rating

Nominal DC Output Voltage

Maximum Supply Current for Main and Aux. Outputs on Power Supply board and ACM8(CB) Access Power Controllers outputs

Fail-Safe/Fail-Secure Outputs

Additional Fused Outputs

ACM8 CB Board Input Fuse Rating

ACM8 Board Output Fuse Rating

ACM8CB Board Output PTC Rating

ACM4 CB Board Input Fuse Rating

ACM4 Board Output Fuse Rating

ACM4CB Board Output PTC Rating

PD16W Board Output Fuse Rating

PD16WCB Board Output PTC Rating

Power Supply 1

Power Supply 2

DC

Aux

DC

Aux

Output Range VDC

Output Range VDC

Output Range VDC

Output Range VDC

T3SSK75F28

7.5

eFlow104NB 6.3A/ 250V eFlow102NB 5A/ 250V

15A/ 32V

20.17- 26.4

20.28- 26.4

9.7- 13.2

10.03- 13.2

24VDC 9.4A 12VDC 10A

28

16

10A/ 250V

3.5A/ 250V

10A/ 32V

3A/ 32V

3.5A/ 250V

T3SSK75F28D

2.5A

2.5A

2.5A

Installation Instructions

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure.
2. Do not discard hardware.
3. Mark and predrill holes in the wall to line up with the top two/three keyholes in the enclosure.
4. Install two/three upper fasteners and screws in the wall with the screw heads protruding.
5. Place the enclosure’s upper keyholes over the two/three upper screws level and secure. Mark the position of the lower three holes.
6. Remove the enclosure.
7. Drill the lower holes and install the three fasteners.
8. Place the enclosure’s upper keyholes over the two/three upper screws.
9. Install the three lower screws and make sure to tighten all screws.
10. Mount included UL Listed tamper switches Altronix Model TS112 or equivalent) in desired locations, opposite hinge. ;
11. Slide the tamper switch bracket onto the edge of the enclosure approximately 2 from the right side.
12. Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
13. To activate alarm signal open the door of the enclosure.
14. Mount S2-INST Installation Kit to backplane ACM8(CB) and PD16W(CB) for further installation instructions.

T3SSK75F28(D)

Access Controller Position Chart for the S2-INST Installation Kit

1. Align S2-INST mounting holes with pems on TSS3.
2. Attach S2-INST to backplane with lock nuts provided.
3. Mount backplane to enclosure with hardware.
4. Fasten TSS3 backplane to Trove3 enclosure utilizing hardware provided.

Trove3 Enclosure Dimensions H x W x D approximate

36.12x 30.125 x 7.06 917.5mm x 768.1mm x 179.3mm

Altronix is not responsible for any typographical errors 140 58th Street, Brooklyn, New York 11220 USA

• Phone: 718-567-8181
• Fax: 718-567-9056
• Web site: www.altronix.com
• E-mail: info@altronix.com
• Lifetime Warranty IITrove3 SS Kits.

Documents / Resources

	Altronix T3SSK75F28 28 Door Kit with Fused Outputs [pdf] Installation Guide T3SSK75F28 28 Door Kit with Fused Outputs, T3SSK75F28, 28 Door Kit with Fused Outputs
	Altronix T3SSK75F28 28 Door Kit with Fused Outputs [pdf] Installation Guide T3SSK75F28, T3SSK75F28D, 28 Door Kit with Fused Outputs, T3SSK75F28 28 Door Kit with Fused Outputs, T3SSK75F28 28 Door Kit

References

• User Manual