T2AGK78V 8 Door Kit with Fused Outputs

trove logo

Access & Power Integration

Altronix/AMAG M4000 Kits
Models Include:

T2AGK78V
8 Door Kit with Fused Outputs
Fully assembled kit includes:
– Trove2 enclosure with TAG2 Altronix/AMAG backplane
– One (1) AL1024XB2V – Power Supply/Charger
– One (1) ACM8 – Fused Access Power Controller
– One (1) VR6 – Voltage Regulator
– One (1) PDS8 – Dual Input Fused Power Distribution Module

T2AGK78V
8 Door Kit with Fused Outputs
Fully assembled kit includes:
– Trove2 enclosure with TAG2 Altronix/AMAG backplane
– One (1) AL1024XB2V – Power Supply/Charger
– One (1) ACM8 – Fused Access Power Controller
– One (1) VR6 – Voltage Regulator
– One (1) PDS8 – Dual Input Fused Power Distribution Module

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™ Rev. 050322

Installing Company: _________________________ Service Rep. Name: __________________________________________ Address: _________________________________________________________ Phone #: _________________________

Overview:

Altronix T2AGK78V and T2AGK78V Trove AMAG kits are pre-assembled and consist of Trove2AG2 enclosure/backplane with factory installed  Altronix power supply/charger and sub-assemblies. These kits also accommodate up to two (2) AMAG M4000 modules for up to eight (8) doors  in a single enclosure.

Configuration Chart:

chart

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.  Product is intended for indoor use only.  

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the  wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure. Mark the position  of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes  over the three upper screws. Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location, opposite hinge.  

enclosureSlide the tamper switch bracket onto the edge of the enclosure, approximately 2” from  the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel  input or the appropriate UL Listed reporting device.  

To activate alarm signal open the door of the enclosure.

4. Mount AMAG M4000 modules to TAG2 backplane, refer to page 3. 5. Refer to the XBV Power Supply/Charger Installation Guide for  

AL1024XB2V and corresponding Sub-Assembly Installation Guides for  the following models: ACM8(CB), PDS8(CB) and VR6 for further installation instructions.  

 Hardware:

hardware

T2AGK78(D)V: Configuration of AMAG M4000 Modules:

1. Align the AMAG M4000 modules on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 2a, pg. 3).

3. Mount AMAG M4000 modules to spacers utilizing pan head screws (provided) (Fig. 2a, pg. 3).

Note: AMAG M4000 modules have one (1) screen. Please make sure that they are mounted correctly, as shown in Fig. 2 below.

4. Fasten TAG2 backplane to Trove2 enclosure utilizing hardware (provided).

amag

Enclosure Dimensions (H x W x D approximate):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm)

dimension

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty
IIT2AGK78(D)

Documents / Resources

Altronix T2AGK78V 8 Door Kit with Fused Outputs [pdf] Installation Guide
T2AGK78V 8 Door Kit with Fused Outputs, T2AGK78V, 8 Door Kit with Fused Outputs, Kit with Fused Outputs, Fused Outputs

References

Leave a comment

Your email address will not be published. Required fields are marked *