More than just power.™
T2MK3F8Q2 8-Door Kit with Fused Outputs
Installation Guide

The fully assembled kit includes:

• Trove2 enclosure with TM2 Altronix/Mercury backplane
• One (1) eFlow6NB – Power Supply/Charger
• One (1) LINQ2 – Network Communications Module
• One (1) ACM8 – Fuse Protected Access Power Controller
• One (1) RSB1 Rocker Switch Bracket with One (1) Rocker Switch (Not evaluated by UL)

Installation Guide
All components of this Trove kit are UL Listed as sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
All registered trademarks are the property of their respective owners.
Rev. 032520
Installing Company: ________________________
Service Rep. Name: _________________________
Address: _________________________________
Phone #: _________________________________

Overview:

Altronix T2MK3F8Q2 Trove Mercury kit is pre-assembled and consists of a Trove2M2 enclosure with factory-installed Altronix power supply/charger and sub-assemblies. T2MK3F8Q2 kit also accommodates various combinations of Mercury boards for up to eight (8) doors in a single enclosure.
Configuration Chart:

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. The product is intended for indoor use only.

1. Remove backplane(s) from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in the desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, on the right).
   Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate the alarm signal open the door of the enclosure.
4. Mount Mercury boards to the backplane, refer to pg. 3.
5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB, and corresponding Sub-Assembly Installation Guides for LINQ2 and ACM8 for further installation instructions.

Hardware:

	Snap On Spacer
	5/16” Pan Head Screw
	Lock Nut

T2MK3F8Q2: Configuration of Mercury Boards:

1. Fasten snap-on standoffs onto metal pens configuration (A), (B), (C), or (D) of the backplane depending on the access controller (Fig. 2, pg.
2. Position the access controller module over corresponding standoffs and depress it onto snap-on standoffs (Fig. 2a, pg. 3).
3. Mount the backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

Mercury Access Controller	Pem Mounting
EP1502, MR52, MR16IN, MR16OUT	A
EP2500, MUX8	B
EP1501, MR51e	C
MR50	D

Trove2 Enclosure Dimensions (H x W x D approximate): 27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm)

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA
Phone: 718-567-8181
Fax: 718-567-9056
Web Site: www.altronix.com
E-mail: info@altronix.com
Lifetime Warranty
IIT2MK3F8Q2 J22UT2MK3F8Q2 Installation Guide

Documents / Resources

Altronix TROVE T2MK3F8Q2 8 Door Kit with Fused Outputs [pdf] Installation Guide TROVE T2MK3F8Q2 8 Door Kit with Fused Outputs, TROVE T2MK3F8Q2, TROVE, T2MK3F8Q2, 8 Door Kit with Fused Outputs, 8 Door Kit, Door Kit and Fused Outputs, Kit and Fused Outputs

References

• User Manual