AJCloud CL31 Battery Security Camera User Manual

AJCloud CL31 Battery Security Camera User Manual

Email: ajcloudservice@outlook.com

Before operating this unit please read these instructions carefully and save them for future use.

Product Introduction

Please fully charge it for the first use.
Note: The solar panel installation location should be selected in the location with the most sun exposure. The installation direction should not be latte avoid water or snow accumulation.

Software installation

APP Download and Installation
Users can search”AJCloud” on APP store or Google Play. of scan the OR code below to install the APP
APP download

Installation Video

Step 1
If you are prompted to open certain permissions (such as I location, message notification, etc.) during APP installation, click Allow (agree).
Step 2

Account register: Open the APP,click” Sign up”, enter your email or phone number to create an account

Account login: On the login interface, enter the account/phone number/email, and the corresponding password and click the “OK” button to log in

Third-party login: APP supports third- party login. Click the third-party sock software icon, jump to the APP to complete weatherization and log in.

Bluetooth adding process with network

“Before adding a camera, please make sure that the Bluetooth funmen of the motile phone has been turned on, nail do not tum off the Bluetooth dunng the adding process. If a promo l bos props up during the adding process to noble Bluetooth or Bluetooth reauthorizing, please follow the taps in the prompt to enable
Step 1
After the camera is powered on, open the “AJCloud “APP and click the “+” icon in the upper right corner to enter the Interface of adding devices.

Step 2
The APP will automatically search for a new device and click the “Pair” button when it finds the device.

If you can’t find the device in the above steps, press and hold the reset button for 5 seconds, restore the camera to factory settings, and try again.

Step 3
Enter the WiFi name and password on the distribution network screen (This product only supports 2.4G Wifi, please connect to the 2.4G WiFi, not 5G WiFi)

Step 4
After the network is configured successfully, the system prompts you to enter the device name. Click Next.

Or you can add camera by WiFi configuration

Step 1
Open the APP, click the “+”icon Or click the “Add device to enter the scan code interface:

Step 2
Select the device type Select Battery camera

Step 3
Select Wi-Fi connection by QR code

Step 4
Check whether the device is powered on and has a prompt prompt tone

Step 5
Select the WiFi that the camera needs to connect to, enter the password, and click Next:

Step 6
Point the camera at the QR code that appears on the screen of the phone

Step 7
After the network configuration is successful. set a name for the camera.

If wholeness comes configuration fol, plea Inw the APP guide to configure.

Help FAQ

After Service

1. Thanks for your purchase and support, we appreciate all your valuable feedback.
2. If you have any questions about our products, please feel free to contact us

Toll Free: +1 888 971 6718
Email: ajcloudservice@outlook.com

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and con radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important: Change or modifications not expressly approved by the manufacturer responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B)

Radiation Exposure Statement

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.