FlySky FS-i6

Contents

FLYSKY FS-i6 2.4G 6CH AFHDS 2A Radio Transmitter User Manual

Model: FS-i6 with FS-iA6 / IA6B / A8S / X6B / IA10B Receiver Compatibility

1. Introduction

The FlySky FS-i6 is a 6-channel 2.4GHz AFHDS 2A digital proportional radio control system designed for RC models such as gliders, helicopters, and airplanes. This system offers reliable, interference-free operation with advanced features for both beginners and experienced users. It is compatible with various FlySky receivers including FS-iA6, FS-iA6B, FS-A8S, FS-X6B, and FS-IA10B.

FlySky FS-i6 Radio Transmitter with various compatible receivers
FlySky FS-i6 Radio Transmitter with various compatible receivers (FS-iA6, FS-iA6B, FS-A8S, FS-X6B, FS-IA10B) shown alongside.

2. Safety Guidelines

Always operate your RC equipment responsibly. Failure to do so may result in injury or damage to property. Observe the following precautions:

  • Ensure all batteries are fully charged before operation.
  • Never operate your RC model near people, animals, or property.
  • Always perform a range check before each flight/operation.
  • Keep the transmitter and receiver away from moisture and extreme temperatures.
  • Do not modify the system components unless explicitly instructed by the manufacturer.
  • Always turn on the transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.

3. Package Contents

The standard package includes:

  • 1 x FS-i6 Transmitter
  • 1 x Compatible Receiver (FS-iA6B, FS-A8S, FS-iA6, FS-X6B, or FS-IA10B, depending on your selection)
FlySky FS-i6 transmitter and manual in box
The FlySky FS-i6 transmitter and its quick start manual, presented in its retail packaging.

4. Specifications

FS-i6 Transmitter Specifications:

FeatureSpecification
Channels6 Channels
Model TypeGlider/Heli/Airplane
RF Range2.40-2.48GHz
Bandwidth500KHz
Bands142
RF PowerLess Than 20dBm
2.4GHz SystemAFHDS 2A and AFHDS
Code TypeGFSK
Sensitivity1024
Low Voltage WarningLess than 4.2V
DSC PortPS2; Output: PPM
Charger PortNo
Antenna Length26mm*2 (dual antenna)
Transmitter Weight392g
Transmitter Size174x89x190mm
Power6V (4x 1.5V AA batteries)
Display ModeTransflective STN positive type, 128*64 dot matrix VA73*39mm, white backlight
On-line UpdateYes
ColorBlack
CertificatesCE0678, FCC
Model Memories20
ModesMode 1 (right throttle hand), Mode 2 (left throttle hand)

Receiver Specifications:

Detailed diagram of FlySky FS-i6 transmitter and various compatible receivers with dimensions and port labels.
Detailed diagram illustrating the FlySky FS-i6 transmitter and various compatible receivers (FS-iA6, FS-iA6B, FS-A8S, FS-X6B, FS-IA10B) with their dimensions and port labels.

FS-iA6B Specifications:

  • Channel: 6
  • Frequency Range: 2.4055-2.475GHZ
  • Band Width Number: 140
  • Transmitting Power: < 20dBm
  • RF Receiver Sensitivity: -105dbm
  • 2.4G Mode: Enhanced version of automatic FM digital system (second generation)
  • Encoding: GFSK
  • Antenna Length: 26mm * 2 (dual antenna)
  • Input Power: 4.0-6.5V DC
  • Dimension: 47 x 26.2 x 15mm
  • Weight: 14.9g
  • i-Bus Interface: Yes
  • Data Acquisition Interface: Yes
  • Model Type: Airplane / Glider / Helicopter
  • Compatible Transmitter: FS-i4, FS-i6, FS-i10, FS-GT2E, FS-GT2G

FS-iA6 Specifications:

  • Channels: 6
  • Frequency Range: 2.4-2.48 GHz
  • Number of Band: 140
  • Transmitting Power: < 20dBm
  • Receiver Sensitivity: -105dBm
  • 2.4G modes: Automatic frequency second generation digital systems
  • Encoding: GFSK
  • Weight: 6.4g
  • Input Power: 4.0-6.5V DC
  • Dimensions: 40.4 x 21.1 x 7.35 mm
  • i-BUS Interface: No
  • Data Acquisition Interface: No
  • Certification: CE0678, FCC
  • Usage: Suitable for RC Airplane / glider / helicopter
  • Compatible Transmitter: Flysky FS-i10, FS-i6, FS-i4, FS-GT2F, FS-GT2E, FS-GT2B

FS-A8S Specifications:

  • Channels: PPM 8CH, i-BUS 18CH
  • Model type: Multi-rotor
  • Frequency range: 2.408-2.475GHz
  • Band width: 500KHz
  • Band number: 135
  • RX Sensitivity: -92 dBm
  • 2.4GHz system: AFHDS 2A
  • Modulation type: GFSK
  • DSC port: PPM/i-BUS/S.BUS
  • Transfer method: FHSS
  • Data output: 1.5mm*3 Pin PPM/i-BUS/S.BUS
  • Antenna length: 26mm (Not including brass contacts)
  • Input power supply: 4.0-8.4V
  • Display method: LED
  • No ground interference (Transmitting and receiving 1 m from the ground): >300m
  • Working current: 40mA
  • Channel delay: <15mS
  • Size: 20*14*5.3mm
  • Weight: 1.2g
  • Certificate: CE0678, FCCID: N45ZA8S00
  • Compatible Transmitter: FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F

FS-X6B Specifications:

  • Item: X6B i-BUS 2.4GHz 6CH Receiver
  • Channels: 6(PWM), 8(PPM), 18(i-BUS)
  • Model Type: Multi-Rotor
  • RF Range: 2.408-2.475 GHz
  • Band Width: 500KHz
  • Number of bands: 135
  • RF Power: < 20 dBm
  • RX Sensitivity: -95dBm
  • 2.4GHz protocol: AFHDS 2A
  • Modulation Type: GFSK
  • Stick resolution: 1024
  • Low voltage alarm: Yes
  • DSC port: PPM/PWM/i-BUS
  • Antenna Length: 93mm (Dual Antenna)
  • Power input: 4.0-8.4V
  • On-line Update: Yes (Wireless)
  • Range: >300m
  • Weight: 4.5g
  • Size: 36*22*7.5mm
  • i-BUS Port: Yes
  • Certificate: CE0678, FCC ID: N4ZX6B00
  • Compatible Transmitter: All AFHDS 2A Transmitters (e.g., FS-i10, FS-i6, FS-i6S, FS-i6X, FS-i4, FS-i4X)
  • Note: Failsafe only works on PWM, not in PPM or IBUS.

5. Setup Instructions

5.1. Battery Installation (Transmitter)

  1. Locate the battery compartment on the back of the FS-i6 transmitter.
  2. Slide the battery cover downwards and remove it.
  3. Insert four (4) AA 1.5V batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  4. Replace the battery cover, sliding it upwards until it clicks into place.
Battery compartment of the FS-i6 transmitter
Close-up view of the battery compartment of the FS-i6 transmitter, showing slots for four AA batteries and a warning label.

5.2. Optional 2S Battery Modification (Advanced Users)

WARNING: This modification requires soldering and advanced technical skills. Incorrect installation can damage the transmitter and void your warranty. Proceed with extreme caution.

For users wishing to power the FS-i6 with a 2S 1000mAh battery, internal wiring modifications are necessary. This involves soldering connections to the internal battery terminals. Refer to the following images for guidance on positive and negative connections:

Internal wiring modification for a 2S battery in the FS-i6 transmitter
Image showing the internal wiring modification for a 2S battery in the FS-i6 transmitter, with a soldering iron in use.
FS-i6 battery compartment showing positive and negative terminals for 2S battery modification
Close-up of the FS-i6 battery compartment showing positive and negative terminals for a 2S battery modification.
FS-i6 battery compartment with internal wiring for 2S battery modification
Another view of the FS-i6 battery compartment with internal wiring for a 2S battery modification, highlighting positive and negative connections.
FS-i6 battery compartment showing internal wiring for 2S battery modification
A further close-up of the FS-i6 battery compartment showing the internal wiring for a 2S battery modification.

5.3. Binding the Receiver

The FS-i6 transmitter uses the AFHDS 2A system, which features a unique ID for each transmitter. When binding with a receiver, the receiver saves this unique ID and will only accept data from that specific transmitter, enhancing interference immunity and safety.

  1. Ensure both the transmitter and receiver are powered off.
  2. Connect the bind plug to the B/VCC port on the receiver.
  3. Power on the receiver. The receiver's LED should flash rapidly, indicating it is in bind mode.
  4. While holding down the 'BIND KEY' button on the FS-i6 transmitter (located below the screen), power on the transmitter.
  5. The transmitter's screen will display 'Binding...' or a similar message.
  6. Once binding is successful, the receiver's LED will stop flashing and remain solid.
  7. Release the 'BIND KEY' button on the transmitter.
  8. Power off both the receiver and the transmitter.
  9. Remove the bind plug from the receiver.
  10. Power on the transmitter first, then the receiver. The receiver's LED should be solid, indicating a successful connection.

6. Operating Instructions

6.1. Basic Controls

Front view of the FlySky FS-i6 6-channel radio transmitter
Front view of the FlySky FS-i6 6-channel radio transmitter, displaying its controls and LCD screen.
  • Sticks: Control primary flight surfaces (aileron, elevator, rudder, throttle). The configuration depends on whether your transmitter is set to Mode 1 or Mode 2.
  • Trims: Fine-tune control surfaces to achieve stable flight.
  • Switches: Activate various functions such as flight modes, gear, flaps, etc., depending on your model's setup.
  • Knobs (VRA, VRB): Provide proportional control for auxiliary channels.
  • LCD Screen: Displays telemetry data, model settings, battery voltage, and menu options.
  • Buttons (UP, DOWN, CANCEL, OK): Navigate through the transmitter's menu system to adjust settings.

6.2. Mode Selection (Mode 1 / Mode 2)

The FS-i6 supports both Mode 1 (right throttle) and Mode 2 (left throttle) configurations. This setting determines which stick controls the throttle and aileron/elevator. You can typically change this in the transmitter's system settings menu. Refer to the on-screen menu for specific instructions on how to switch modes.

6.3. Menu Navigation

Use the UP/DOWN buttons to scroll through menu options, the OK button to select an option or confirm a setting, and the CANCEL button to go back or exit a menu.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the transmitter and receiver. Do not use solvents or abrasive cleaners.
  • Storage: Store the equipment in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
  • Battery Care: Always use fresh batteries or properly charged rechargeable batteries. Dispose of old batteries responsibly.
  • Firmware Updates: The FS-i6 supports online firmware updates. Periodically check the official FlySky website for new firmware versions to ensure optimal performance and access to new features.

8. Troubleshooting

8.1. No Power

  • Check if batteries are correctly installed with proper polarity.
  • Ensure batteries have sufficient charge.
  • If using a 2S battery mod, verify connections are secure and correct.

8.2. Receiver Not Binding

  • Ensure the bind plug is correctly inserted into the B/VCC port on the receiver.
  • Verify the receiver is powered on and its LED is flashing.
  • Confirm the 'BIND KEY' on the transmitter is held down while powering on.
  • Try moving the transmitter closer to the receiver during the binding process.
  • Ensure the receiver is compatible with the FS-i6 transmitter (AFHDS 2A system).

8.3. Loss of Signal / Short Range

  • Perform a range check to identify potential issues.
  • Ensure receiver antennas are properly positioned and not obstructed by carbon fiber or metal parts.
  • Check for sources of interference (e.g., Wi-Fi routers, other 2.4GHz devices).
  • Verify the transmitter and receiver are securely bound.

8.4. Controls Not Responding Correctly

  • Check servo connections to the receiver.
  • Verify channel assignments in the transmitter's menu.
  • Ensure trims are centered or adjusted as needed.
  • Recalibrate sticks if necessary (refer to advanced settings in the transmitter menu).

9. User Tips

  • Practice on a Simulator: Before flying your actual model, practice extensively on an RC flight simulator to familiarize yourself with the controls and prevent costly crashes.
  • Start Simple: If you are new to RC, begin with a simpler model and gradually progress to more complex ones as your skills improve.
  • Check Connections: Always double-check all wiring and connections before each use to ensure everything is secure and correctly plugged in.
  • Monitor Battery Voltage: Pay attention to the low voltage warning on your transmitter and land your model safely before the battery runs out.
  • Keep Manual Handy: Refer to the full manual (if available) or online resources for detailed programming and advanced features.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the official FlySky customer service. Keep your proof of purchase for warranty claims. Detailed warranty terms and conditions may be available on the official FlySky website.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.