1. Introduction
The Hobbyeagle A3 Super4 A3S4 is a high-performance and powerful 6-axis gyroscope and balancer designed specifically for fixed-wing aircraft models. Building upon previous generations, it features improved hardware design, full support for multi-protocol digital serial receivers, and customizable output interfaces for enhanced user experience and reliability.
Key Features:
- 32-bit processor with high-precision 6-axis MEMS sensor for reliable performance.
- Six distinct flight modes: Gyro Off, Normal Stabilization, Lock, Angle, Balance, and Hoist.
- Supports various receiver types: PWM, PPM, S.Bus, FrSky S.Bus/WBUS, Spektrum DSM2/X, Multiplex SRXL/JR XBUS Mode B, Graupner SUMD, and FlySky iBus.
- Flexibly configurable output interface with 2 pass-through output channels.
- Supports dual ailerons, dual elevator systems, and includes built-in mixing for flying wing (delta wing) and V-tail configurations.
- Remote overall gain adjustment capability.
- Firmware upgradeable, with support for parameter adjustment via a setting card.
2. Package Contents
Please verify that all items are present in your package:
- 1 x A3 Super 4 Airplane Gyro Flight Controller Stabilizer
- 1 x Voltage Protector
- 1 x Programming Card (Note: May not be included in 'Lite' versions)
- 1 x USB Cable (Note: May not be included in 'Lite' versions)
- 1 x USB Adapter
- 1 x External LED module + 1 x Connector Cable
- 3 x Receiver Wires
- 4 x Tape Stickers


3. Setup and Installation
3.1 Physical Installation
- Mounting: Use the provided tape stickers to securely mount the A3 Super4 flight controller to a flat surface on your aircraft. Ensure the unit is oriented correctly as per the markings on the device.
- Dimensions: The unit measures 30mm x 19.5mm x 7.5mm.
- Weight: The controller weighs 4.8g (excluding wires).
- USB Access: When choosing a mounting location, consider leaving sufficient room for access to the micro USB port on the front of the unit if you plan to connect it to a PC for configuration or firmware updates after installation.
3.2 Wiring Connections
The A3 Super4 supports various receiver types. Below are common wiring diagrams:


3.3 Initial Configuration
After wiring, use the programming card (if included) or connect the unit to a computer via the USB cable and adapter to perform initial setup and calibration. This includes setting up your aircraft type (e.g., normal, flying wing, V-tail) and adjusting basic gains.
4. Operating Modes
The A3 Super4 offers six flight modes to suit various flying styles and conditions:
- Gyro Off Mode: The gyroscope is inactive, and the aircraft responds directly to pilot inputs without stabilization.
- Normal Stabilization Mode: Provides basic stabilization, correcting for external disturbances like wind.
- Lock Mode: Maintains the current attitude of the aircraft, resisting changes until new input is given.
- Angle Mode: Limits the maximum pitch and roll angles, making it easier to control for beginners.
- Balance Mode: Automatically levels the aircraft when control sticks are centered.
- Hoist Mode: Designed for specific maneuvers, often related to vertical flight or hovering.
You can adjust the overall gain remotely during flight to fine-tune the stabilization effect.
5. Maintenance
- Keep the flight controller clean and free from dust and debris.
- Avoid exposing the unit to moisture or extreme temperatures.
- Regularly check all wiring connections to ensure they are secure.
- Periodically check the Hobbyeagle website for firmware updates to ensure optimal performance and access to new features.
6. Troubleshooting
- Unstable flight / erratic control (especially with gas engines): If the controller seems to go 'crazy' or causes continuous wing movement, particularly in high-vibration environments like gas-powered airplanes, try lowering the gains significantly. High vibrations can interfere with the MEMS sensors.
- No response from controls: Check all wiring connections between the receiver, flight controller, and servos. Ensure the flight controller is receiving adequate power (DC3.6V ~ 8.4V). Verify that the correct receiver type is selected in the controller's settings.
- Aircraft disoriented / lost control: If you lose orientation, switching to an 'auto mode' such as Angle or Balance mode can help the gyroscope bring the aircraft back to a level attitude.
- Loss of transmitter signal: The A3 Super4 does not provide an autonomous rescue mode for complete loss of transmitter signal. Consider installing an external autonomous beeper or GPS tracker for model recovery in such situations.
7. Specifications
| Attribute | Value |
|---|---|
| Brand Name | HOBBYEAGLE |
| Model Number | A3S4 |
| Main Controller | 32-bit MCU |
| Sensor | High-precision 6-axis MEMS sensor |
| Input Voltage | DC3.6V ~ 8.4V |
| Working Current | 20mA@5V |
| Size | 30mm x 19.5mm x 7.5mm |
| Weight | 4.8g (excluding wires) |
| Material | Plastic (ABS) |
| Is Electric | No battery |
| For Vehicle Type | Airplanes |
| RC Parts & Accs | RECEIVERS |
| Origin | Mainland China |
| Recommend Age | 14+ years |
8. Warranty and Support
Hobbyeagle products are designed for high performance in R/C models. Specifications are subject to change without notice.
For product authenticity verification, you can query the serial number (S/N) on the official Hobbyeagle website.


For further support, firmware updates, or detailed information, please visit the official Hobbyeagle website: www.hobbyeagle.com. You can also contact support via email: support@hobbyeagle.com.
9. User Tips
- USB Port Access: When installing the unit, ensure you leave enough space around the micro USB port for easy connection to a PC, as it is located on the front of the unit.
- Gas Engine Vibrations: If using the A3 Super4 with a gas-powered airplane, be aware that high vibrations from the engine, especially at low RPMs, can cause erratic behavior. It is recommended to carefully adjust and potentially lower the gains to mitigate this effect.
- Emergency Stabilization: In situations where you become disoriented, switching to an 'auto mode' (such as Angle or Balance mode) can help the gyroscope automatically level the aircraft, providing a chance to regain control.
- Signal Loss: The A3 Super4 does not have a built-in rescue function for complete loss of transmitter signal. For enhanced safety and model recovery, consider equipping your aircraft with an autonomous beeper or a GPS tracking device.
10. Frequently Asked Questions (FAQ)
- Q: How can I utilize this item?
- A: The Hobbyeagle A3 Super4 A3S4 is designed for use as a 6-axis gyro and stabilization balancer in RC Airplanes.
- Q: Is there a rescue mode if I lose control or get disoriented?
- A: While it doesn't have a dedicated 'rescue mode' for signal loss, if you get disoriented, you can switch to an auto-stabilization mode (like Angle or Balance mode). The gyroscope will then work to bring the aircraft to a level horizon, helping you regain control. It does not, however, provide recovery from complete signal loss.
- Q: Is the Gyro compatible with Spektrum receivers?
- A: Yes, the A3 Super4 supports various receiver types, including Spektrum (DSM2/X), as well as S.Bus, I.Bus, PWM, and PPM protocols.
- Q: Can this be used on a gas-powered airplane?
- A: Yes, it can be used with gas-powered airplanes. However, be mindful that high vibrations from gas engines, especially at lower RPMs, might affect the gyroscope's performance. Careful adjustment of the gains is recommended in such applications.