Epever Tracer LPLI series

Contents

Epever Tracer LPLI Series MPPT Solar Charge Controller User Manual

Models: Tracer1305LPLI, Tracer2606LPLI, Tracer2610LPLI, Tracer3906LPLI, Tracer3910LPLI, Tracer5206LPLI, Tracer5210LPLI

1. Introduction

The Epever Tracer LPLI series MPPT solar charge controller is an advanced device that integrates a solar charge controller and an LED constant current driver into a single unit. It is specifically designed for solar LED lighting applications, offering optimized charging and discharging management, especially where dimmer functions are required. This controller utilizes Maximum Power Point Tracking (MPPT) technology to maximize energy harvest from solar panels, enhancing system flexibility and reducing overall system costs.

Front view of the Epever Tracer LPLI solar charge controller
Figure 1: Front view of the Epever Tracer LPLI solar charge controller, showing model name, CE/RoHS marks, and warning labels.

2. Safety Information

WARNING: Failure to follow these safety instructions may result in serious injury or damage to the controller.

  • Never short circuit the PV (solar panel) input or battery wires.
  • Always follow the correct connection sequence: Connect the Load first, then the Battery, and finally the PV (solar panels).
  • Ensure all wiring is correctly polarized before connecting.
  • Do not attempt to disassemble or repair the controller yourself. Refer to qualified personnel.
  • Ensure the controller is installed in a well-ventilated area, away from flammable materials.

3. Product Features

  • Utilizes high-quality components from ST, IR, and Infineon for extended product lifespan.
  • Wide operating temperature range: -40℃ to 60℃.
  • Specifically designed for lithium batteries, including self-activating and low-temperature protection functions.
  • Automatic load power reduction feature.
  • Maximum conversion efficiency of 98%.
  • Advanced Maximum Power Point Tracking (MPPT) technology with tracking efficiency no less than 99.5%.
  • Ultra-fast tracking speed and guaranteed tracking efficiency.
  • Accurate recognition and tracking of multiple power points.
  • Automatic identification of 12/24VDC system voltage or user-defined working voltage.
  • Digital precision constant current control with accuracy less than ±2%.
  • Maximum output efficiency of 96%.
  • PV and Load power limitation function.
  • Output current is adjustable within the rated power and current range.
  • Monitoring and parameter setting via Mobile APP or PC Monitor software using an RS485 communication interface.
  • Durable aluminum housing for superior cooling.
  • Real-time energy statistics function.
  • IP68 waterproof rating (suitable for 1.5m depth for 72 hours).
  • Designed for long lifespan with a five-year warranty.

4. Electronic Protections

The controller is equipped with comprehensive electronic protections to ensure system safety and longevity:

  • PV reverse polarity protection
  • Battery reverse polarity protection
  • Battery over voltage protection
  • Battery over discharge protection
  • Battery overheating protection
  • Load short circuit protection
  • Lithium battery low temperature protection (default 0℃)

5. Specifications

Refer to the table below for detailed technical specifications of the Tracer LPLI series models.

Technical specifications table for Epever Tracer LPLI series
Figure 2: Technical specifications for Tracer LPLI series models.
Technical Specifications - Tracer LPLI Series
Parameter Tracer1305LPLI Tracer2606LPLI / Tracer2610LPLI Tracer3906LPLI / Tracer3910LPLI Tracer5206LPLI / Tracer5210LPLI
Nominal system voltage 12VDC 12/24VDC AUTO
Rated charge current 10A 10A 15A 20A
Rated charge power 130W/12V 130W/12V, 260W/24V 195W/12V, 390W/24V 260W/12V, 520W/24V
Max. PV open circuit voltage 50V (Min.Temp.) / 45V (25℃) Tracer****06LPLI: 60V (Min.Temp.) / 46V (25℃)
Tracer****10LPLI: 95V (Min.Temp.) / 92V (25℃)
MPP Voltage range (Battery voltage +2V)~36V Tracer****06LPLI: (Battery voltage +2V)~36V
Tracer****10LPLI: (Battery voltage +2V)~72V
Max. output current 3.3A 3.3A 4.5A 6.6A
Max. output power 100W 100W 130W 200W
Output voltage range (Battery voltage +2V)~46V Tracer****06LPLI: (Battery voltage +2V)~46V
Tracer****10LPLI: (Battery voltage +2V)~80V
Load open circuit voltage 46V Tracer****06LPLI: 46V
Tracer****10LPLI: 80V
Load over voltage protection 50V Tracer****06LPLI: 50V
Tracer****10LPLI: 100V
Maximum output efficiency 96%
Output current control accuracy ≤2%
Battery Type LiFePO4 / Li-NiCoMn / User
Boost charging voltage* LiFePO4:14.6V / Li-NiCoMn:12.51V / User:9-34V
Float charging voltage* LiFePO4:14.4V / Li-NiCoMn:12.39V / User:9-34V
Low voltage reconnect voltage* LiFePO4:12.0V / Li-NiCoMn:10.8V / User:9-34V
Low voltage disconnect voltage* LiFePO4:10.6V / Li-NiCoMn:9.3V / User:9-34V
Self-consumption ≤15mA/12V; ≤22mA/24V
Communication IR communication
Overall dimension 124×89×30mm 150.5x93.5x32.7mm 153.3x105x52.1mm
Net weight 0.52kg 0.52kg 0.71kg 1.18kg
Enclosure IP68 (1.5m, 72h)
Working environment temperature -40℃~+60℃
*Programmable voltage value by SPP-02, RC-02 and APP.

6. Installation and Setup

Follow these steps for proper installation of your Epever Tracer LPLI series controller:

  1. Prepare Wiring: Ensure all wires are of appropriate gauge for the current and length, and that they are properly insulated. Strip wire ends carefully.
  2. Connect Load: Connect the load (e.g., LED light) to the controller's load terminals first. Ensure correct polarity (positive to positive, negative to negative).
  3. Connect Battery: Connect the battery to the controller's battery terminals. Double-check polarity. The controller will automatically detect the system voltage (12V or 24V) or use your pre-defined setting.
  4. Connect PV (Solar Panels): Connect the solar panels to the controller's PV terminals. Verify correct polarity. The controller will begin charging the battery.
  5. Secure Connections: Ensure all wire connections are tight and secure to prevent loose connections and potential hazards.
  6. Mounting: Mount the controller in a suitable location, ensuring good ventilation and protection from direct sunlight or extreme weather, despite its IP68 rating.
Diagram of a typical solar LED lighting system setup
Figure 3: Typical solar LED lighting system setup with Epever controller.

7. Operation

Once installed, the controller operates automatically, managing the charging and discharging processes. You can monitor and configure its behavior using various methods:

7.1 Load Working Modes

The controller supports several load working modes, which can be configured to suit your lighting needs:

  • Manual Mode: Load is turned ON/OFF manually.
  • Light ON/OFF (Default): Load turns ON at dusk and OFF at dawn.
  • Light ON + Timer: Load turns ON at dusk and stays ON for a set duration.
  • Real-time Control: Load operation is controlled based on real-time settings.
  • Intelligent Power Mode: Advanced mode for optimized power management.

7.2 Monitoring and Configuration

The controller can be monitored and configured using:

  • Mobile APP: Connect wirelessly to view real-time data and adjust settings.
  • PC Monitor Setting Software: Use a computer with an RS485 communication interface to access detailed parameters and logs.

7.3 Lithium Battery Management

The controller includes specific features for lithium batteries:

  • Self-activating Function: Automatically activates lithium batteries.
  • Low Temperature Protection: Prevents charging when battery temperature is below 0℃ to protect battery health.

8. Maintenance

To ensure optimal performance and longevity of your Epever Tracer LPLI controller, perform the following maintenance tasks:

  • Inspect Connections: Periodically check all wiring connections (PV, battery, load) for tightness and corrosion. Tighten any loose connections.
  • Clean Controller: Although IP68 rated, occasionally wipe down the controller's exterior to remove dust, dirt, or debris that might accumulate and affect heat dissipation.
  • Check for Damage: Visually inspect the controller for any physical damage, cracks, or signs of overheating.
  • Monitor Performance: Regularly check the system's performance via the mobile app or PC software to ensure proper charging and load operation.

9. Troubleshooting

If you encounter issues with your controller, refer to the following common troubleshooting steps:

  • No Power/Controller Not Responding:
    • Check battery connections and ensure the battery has sufficient charge.
    • Verify PV input connections and ensure solar panels are receiving sunlight.
    • Inspect any inline fuses or circuit breakers in the system.
  • Load Not Working:
    • Check load connections for proper wiring and polarity.
    • Verify the selected load working mode (e.g., if in Manual Mode, ensure it's turned ON).
    • Ensure the battery voltage is above the low voltage disconnect threshold.
  • Battery Not Charging:
    • Check PV connections and ensure solar panels are producing voltage.
    • Verify that the battery type setting in the controller matches your battery.
    • Ensure the battery temperature is above 0℃ if using lithium batteries with low-temperature protection enabled.
  • Overheating:
    • Ensure the controller is mounted in a location with adequate airflow.
    • Check if the load or PV input exceeds the controller's rated capacity.

For persistent issues, contact customer support.

10. Warranty and Support

The Epever Tracer LPLI series solar charge controller comes with a five-year warranty, reflecting its long lifespan design and high-quality construction.

For technical support, warranty claims, or further assistance, please contact your authorized Epever dealer or the manufacturer directly. Ensure you have your product model and purchase information available when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.