FLYSKY FS-GT2E

Contents

FLYSKY FS-GT2E AFHDS 2A 2.4G 2CH Remote Transmitter with FS-A3 Receiver

User Instruction Manual

This manual provides detailed instructions for the setup, operation, and maintenance of your FLYSKY FS-GT2E remote control system. Please read thoroughly before use.

1. Product Overview

The FLYSKY FS-GT2E is a 2-channel 2.4GHz remote control transmitter utilizing AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) technology, paired with an FS-A3 receiver. This system is designed for reliable control of various RC models, typically cars and boats.

FLYSKY FS-GT2E Transmitter and FS-A3 Receiver
Figure 1: FLYSKY FS-GT2E Transmitter and FS-A3 Receiver
FLYSKY FS-GT2E Transmitter Side View
Figure 2: Side view of the FS-GT2E Transmitter

2. Setup Guide

2.1 Transmitter Battery Installation

  1. Open the battery compartment cover located at the bottom of the transmitter handle.
  2. Insert 4 'AA' (LR6) batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  3. Close the battery compartment cover securely.
Transmitter Battery Compartment (AA LR6)
Figure 3: Transmitter battery compartment for 4 'AA' batteries

2.2 Receiver Connection

Connect the FS-A3 receiver to your model's electronic speed controller (ESC) and steering servo. Ensure correct polarity for all connections.

  • Channel 1 (CH1): Steering Servo
  • Channel 2 (CH2): ESC (Throttle)
  • The receiver is powered via the ESC connection.
FS-A3 Receiver and Binding Plug
Figure 4: FS-A3 Receiver with binding plug and antenna

2.3 Binding the Transmitter and Receiver

Binding is the process of linking the transmitter and receiver. This needs to be done once per receiver.

  1. Ensure the transmitter batteries are installed and the power switch is OFF.
  2. Connect the binding plug (included with the receiver) to the 'BIND' port on the FS-A3 receiver.
  3. Power on your RC model (this will power the receiver). The receiver's LED should flash rapidly.
  4. While holding down the 'BIND' button on the transmitter's control panel, switch the transmitter ON.
  5. The transmitter's 'G.LED' (Green LED) should flash, and the receiver's LED should stop flashing and remain solid.
  6. Release the 'BIND' button on the transmitter.
  7. Turn off the receiver power, then turn off the transmitter.
  8. Remove the binding plug from the receiver.
  9. Power on the transmitter first, then the receiver. The receiver's LED should be solid, indicating a successful bind.
Transmitter Control Panel (Trims, Reverses, Bind Button, LEDs)
Figure 5: Transmitter control panel showing BIND button, trims, and reverse switches

3. Operating Instructions

3.1 Basic Controls

  • Steering Wheel: Controls the left/right direction of your model. Turn clockwise for right, counter-clockwise for left.
  • Throttle Trigger: Controls the speed and direction (forward/reverse) of your model. Pull back for forward, push forward for reverse/brake.
Transmitter Steering Wheel Detail
Figure 6: Close-up of the steering wheel for precise control

3.2 Adjustments and Settings (Refer to Figure 5)

  • ST.TRIM (Steering Trim): Adjusts the neutral position of the steering servo. Use to make your model drive straight without steering input.
  • TH.TRIM (Throttle Trim): Adjusts the neutral position of the throttle. Use to ensure the motor stops completely when the trigger is at neutral, or to fine-tune idle speed for nitro models.
  • ST.REV (Steering Reverse): Reverses the direction of the steering channel. Flip this switch if your model steers left when you turn right, and vice-versa.
  • TH.REV (Throttle Reverse): Reverses the direction of the throttle channel. Flip this switch if your model goes reverse when you pull the trigger back.
  • ST.DR (Steering Dual Rate): Adjusts the maximum steering angle. Turn the dial to limit or increase the steering throw, useful for different driving conditions or skill levels.
  • BIND Button: Used for linking the transmitter and receiver (see Section 2.3).
  • R.LED (Red LED): Indicates low battery voltage for the transmitter.
  • G.LED (Green LED): Indicates the transmitter is powered ON and operating normally.

4. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the transmitter and receiver. Avoid using solvents or harsh chemicals.
  • Battery Care: Remove batteries from the transmitter if it will not be used for an extended period to prevent leakage.
  • Storage: Store the remote control system in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Antenna: Ensure the receiver antenna is not cut or damaged, as this can affect range and signal quality.

5. Troubleshooting

  • No Power:
    • Check if the transmitter batteries are correctly installed and fully charged.
    • Ensure the power switch is in the 'ON' position.
  • No Control/Erratic Control:
    • Verify that the transmitter and receiver are properly bound (refer to Section 2.3).
    • Check all connections between the receiver, ESC, and servos.
    • Ensure the receiver antenna is properly positioned and undamaged.
    • Check for interference from other 2.4GHz devices in the operating area.
    • Ensure transmitter and receiver batteries are adequately charged.
  • Steering/Throttle Not Responding Correctly:
    • Adjust ST.TRIM or TH.TRIM as needed.
    • Check ST.REV or TH.REV switches if controls are reversed.
    • Inspect servos and linkages for mechanical issues.
  • Fail-Safe Functionality: The FS-A3 receiver is designed with a basic fail-safe feature. In case of signal loss, the throttle channel will return to a pre-set neutral position to prevent runaway models. Ensure your ESC is calibrated to this neutral position.

6. Specifications

Feature Specification
Brand Name FLY SKY
Model Number FS-GT2E
Channels 2CH
Frequency 2.4GHz AFHDS 2A
Receiver FS-A3
Transmitter Power 4x 'AA' (LR6) Batteries (Not Included)
Is Batteries Included No
Recommended Age 14+ years
Approx. Product Weight 0.51 kg (Transmitter and Receiver)
Origin Mainland China

7. User Tips

  • Compatibility: This system is known to be well-suited for various RC models, including Tamiya models.
  • Power Adjustment: While there isn't a direct 'power adjustment' knob, you can limit the maximum throttle output using the 'ST.DR' (Steering Dual Rate) dial if your ESC supports it, or by adjusting the throttle end points on your ESC if it has programming capabilities. The 'TH.TRIM' can fine-tune the neutral throttle position.
  • Fail-Safe Check: Always test the fail-safe function before operating your model. With the model powered on and the transmitter linked, turn off the transmitter. The model's throttle should return to neutral.

8. Warranty and Support

For any issues or support inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.