Introduction
This manual provides detailed instructions for the proper use and maintenance of your Flysky Simulator and Upgrade Data Cable. This versatile cable is designed to connect your Flysky RC transmitter to a computer for firmware upgrades, data downloads, and use with flight simulator software. Please read this manual thoroughly before use to ensure optimal performance and longevity of your product.
Product overview and connection demonstration.
Setup Instructions
Follow these steps to properly set up your Flysky cable:
- Identify Cable Type: The product includes different cable configurations. One type features a USB connector on one end and a round DIN connector (often 4-pin or 6-pin) on the other, typically used for firmware upgrades and data transfer. Another type may feature a 3.5mm audio jack connector, often used for simulator connections.
- Connect to Transmitter:
- For Upgrade/Download Data Cable (DIN connector): Locate the data port on your Flysky transmitter (e.g., FS-I6, FS-I6X, FS-GT5, FS-GT3B). This port is usually a round multi-pin connector. Carefully insert the DIN connector end of the cable into this port.
- For Simulator Cable (3.5mm jack): Locate the trainer port or simulator port on your Flysky transmitter. This is typically a 3.5mm audio jack. Insert the 3.5mm jack end of the cable into this port.
- Connect to Computer: Insert the USB end of the cable into an available USB port on your computer.
- Driver Installation (if required): Your operating system may automatically install necessary drivers. If not, you may need to download and install specific USB drivers for the Flysky cable from the official Flysky website or your transmitter's support page. Refer to your transmitter's manual for driver information.
- Software Preparation:
- For Firmware Upgrades/Data Download: Open the appropriate Flysky firmware update utility or data management software on your computer.
- For Simulator Use: Launch your preferred RC flight simulator software.
Image showing the cable connected to a compatible Flysky transmitter.
Operating Instructions
Using as an Upgrade/Download Data Cable
This function allows you to update your transmitter's firmware or transfer model data between your transmitter and computer.
- Ensure your transmitter is powered on and connected to the computer via the data cable.
- Open the Flysky firmware update tool or data management software on your computer.
- Follow the on-screen instructions within the software to initiate firmware updates or data transfer. Ensure the process is not interrupted.
- Once complete, safely disconnect the cable from both the computer and the transmitter.
Using as a Simulator Cable
The simulator cable allows you to use your Flysky transmitter with RC flight simulator software on your computer.
- Connect the simulator cable to your transmitter's trainer port and to your computer's USB port.
- Important Note for GT2B/GT3C users: If your transmitter is a GT2B or GT3C, you must connect the two cables (the simulator cable and your transmitter's USB cable) together. The simulator cable itself does not directly connect to the computer for these models; it acts as an adapter for your transmitter's existing USB cable.
- Power on your transmitter. Some transmitters may require you to enable "Trainer Mode" or "Simulator Mode" in their settings. Refer to your transmitter's manual for specific instructions.
- Launch your RC flight simulator software. The software should detect your transmitter as a joystick or game controller.
- Calibrate your transmitter within the simulator software if prompted.
Image showing the simulator cable with a 3.5mm jack, commonly used for simulator connections.
Maintenance
- Keep the cable clean and dry. Avoid exposure to moisture, dust, and extreme temperatures.
- Do not bend the cable sharply or apply excessive force to the connectors, as this can damage internal wiring.
- Store the cable neatly coiled to prevent tangling and kinking.
- Regularly inspect the connectors for any signs of wear or damage.
Troubleshooting
- Cable not recognized by computer:
- Ensure the USB connector is fully inserted into a working USB port.
- Try a different USB port on your computer.
- Verify that the necessary drivers are installed. Check your computer's Device Manager for any unknown devices or driver errors.
- Restart your computer and try again.
- Transmitter not responding in simulator:
- Confirm the cable is securely connected to both the transmitter and the computer.
- For GT2B/GT3C, ensure the simulator cable is correctly connected with your transmitter's own USB cable as an adapter.
- Check your transmitter's settings to ensure "Trainer Mode" or "Simulator Mode" is activated.
- Verify that the simulator software is correctly configured to recognize your transmitter as a controller.
- Try calibrating the controller within the simulator software.
- Firmware upgrade or data download fails:
- Ensure a stable connection between the cable, transmitter, and computer.
- Confirm that the correct firmware update utility is being used and that it is up-to-date.
- Ensure your transmitter has sufficient power (e.g., fully charged batteries) before starting an upgrade.
- Do not disconnect the cable or power off the transmitter/computer during the upgrade process.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | Flysky (U-Angel-1988) |
| Model Number | Flysky FS I6 usb cable |
| Compatibility | Flysky FS-I6, FS-I6X, FS-GT5, FS-GT3B, GT3, GT2, GT3B Transmitters |
| Use | Vehicles & Remote Control Toys (Upgrade/Download Data, Simulator) |
| Material | Simulator Cable (generic material) |
| Quantity | 1 pcs |
| Is Electric | No Battery |
| Is Batteries Included | No |
| Recommend Age | 14+y |
| Package Dimensions (approx.) | Length: 10 cm, Width: 10 cm, Height: 10 cm |
| Package Weight (approx.) | 0.08 kg |
User Tips
- GT2B/GT3C Simulator Connection: For Flysky GT2B or GT3C transmitters, the simulator cable acts as an adapter. You must connect the simulator cable to the transmitter's trainer port, and then connect the transmitter's standard USB cable to the simulator cable's USB port, and finally to your computer. This creates the necessary connection for simulator use.
- Driver Verification: If your computer doesn't automatically recognize the cable, check the Device Manager (Windows) or System Information (macOS) to see if the device appears. If it shows an error or is listed as an unknown device, manual driver installation may be required.
- Software Compatibility: Always ensure your simulator software or firmware update tool is compatible with your specific Flysky transmitter model and the cable. Outdated software can lead to connection issues.
Warranty and Support
For any technical assistance, troubleshooting beyond this manual, or inquiries regarding product defects, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.