FlySky FS-R9B Receiver

Contents

FlySky FS-R9B 2.4Ghz 8CH GFSK Receiver User Manual

Model: FS-R9B Receiver | Brand: FlySky

1. Introduction

This manual provides detailed instructions for the proper setup, operation, and maintenance of your FlySky FS-R9B 2.4Ghz 8-channel GFSK receiver. Designed for use with various RC models including fixed-wing aircraft, copters, and helicopters, this receiver ensures reliable communication with compatible FlySky transmitters, such as the Turnigy 9X.

Please read this manual thoroughly before using the product to ensure safe and optimal performance.

2. Safety Information

  • Always ensure the receiver is securely mounted in your model to prevent damage from vibrations or impacts.
  • Verify all connections are correct and secure before powering on your model. Incorrect wiring can lead to damage or loss of control.
  • Operate your RC model in open areas, away from people, vehicles, and other potential hazards.
  • Avoid operating your model near power lines, radio towers, or other sources of electromagnetic interference, which can affect signal reception.
  • Always turn on your transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.
  • Keep the receiver away from moisture, extreme temperatures, and direct sunlight.
  • This product is recommended for users aged 14 years and older.

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Package Contents

Your package should contain the following items:

  • 1x FlySky FS-R9B 2.4Ghz 8CH GFSK Receiver
  • 1x Bind Plug
FlySky FS-R9B receiver with bind plug and antenna
Image: The FS-R9B receiver, showing the main unit, antenna, and included bind plug.

4. Product Overview

The FS-R9B is an 8-channel 2.4Ghz GFSK receiver. It features standard servo connections and a dedicated bind port.

Close-up of FlySky FS-R9B receiver ports
Image: Top view of the FS-R9B receiver, highlighting the channel ports (CH1-CH8), BIND port, and BAT port.

Receiver Ports:

  • CH1 - CH8: Standard servo output channels. Connect your servos, ESC, or other control devices here.
  • BIND: Used for binding the receiver to your transmitter.
  • BAT: Power input port. Typically used when the ESC does not provide power to the receiver, or for external battery connection during binding.

5. Setup

5.1. Binding the Receiver to your Transmitter

Binding is the process of electronically linking the receiver to your transmitter. This must be done before first use and if you change transmitters.

  1. Ensure your transmitter is turned OFF.
  2. Insert the bind plug into the BIND port on the FS-R9B receiver.
  3. Connect power to the receiver via the BAT port or through any channel port (e.g., from an ESC with BEC). The receiver's LED should start flashing rapidly, indicating it is in bind mode.
  4. Turn on your transmitter while holding down its bind button (the exact procedure may vary by transmitter model, refer to your transmitter's manual).
  5. The receiver's LED should stop flashing and remain solid, indicating a successful bind.
  6. Release the bind button on your transmitter.
  7. Disconnect power from the receiver, then remove the bind plug.
  8. Turn off your transmitter.
  9. Reconnect power to the receiver (without the bind plug).
  10. Turn on your transmitter. The receiver's LED should be solid, confirming a successful connection.

Note: If the binding process fails, repeat the steps carefully. Ensure your transmitter is in the correct mode (e.g., PPM/PWM) if applicable.

5.2. Connecting Servos and ESC

Connect your servos, Electronic Speed Controller (ESC), and other components to the appropriate channels on the receiver. Refer to your model's specific wiring diagram for correct connections.

  • ESC: Typically connects to CH3 (throttle) for most aircraft, or as specified by your flight controller.
  • Servos: Connect to CH1, CH2, CH4, etc., according to your model's control surfaces (aileron, elevator, rudder).
  • Ensure the polarity of all connections is correct (signal, positive, negative).

6. Operating the Receiver

  1. Power On: Always turn on your transmitter first. Then, connect the battery to your model, which will power the receiver. The receiver's LED should illuminate solid, indicating a successful link with the transmitter.
  2. Pre-Flight Checks: Before each flight, perform a range check and verify that all control surfaces and motor functions respond correctly to your transmitter inputs.
  3. Power Off: Disconnect the battery from your model (turning off the receiver) first. Then, turn off your transmitter.

7. Maintenance

  • Cleaning: Gently clean the receiver with a soft, dry cloth. Avoid using solvents or harsh chemicals.
  • Storage: Store the receiver in a dry, cool environment, away from direct sunlight and extreme temperatures.
  • Antenna Care: Ensure the receiver antenna is not cut, kinked, or damaged. A damaged antenna can significantly reduce range and signal reliability. Position the antenna away from carbon fiber or metal parts of your model for best reception.

8. Troubleshooting

ProblemPossible CauseSolution
Receiver LED not solid after power onNot bound to transmitter, transmitter off, or out of range.Perform the binding procedure again. Ensure transmitter is on and within range. Check power connections.
No response from servos/ESCIncorrect wiring, faulty servo/ESC, or receiver not powered.Verify all connections and polarity. Test servos/ESC with another receiver or servo tester. Check receiver power.
Intermittent signal lossAntenna damage/poor placement, interference, or low transmitter battery.Inspect antenna for damage and ensure optimal placement. Avoid operating near interference sources. Check transmitter battery level.
Binding fails repeatedlyIncorrect binding procedure, incompatible transmitter, or faulty bind plug/receiver.Review binding steps carefully. Ensure transmitter is compatible (FlySky 2.4Ghz GFSK). Try a different bind plug if available.

9. Specifications

FeatureDetail
Model NumberFS-R9B Receiver
Channels8 Channels
Frequency2.4Ghz
ModulationGFSK
CompatibilityFlySky 2.4Ghz Transmitters (e.g., Turnigy 9X)
ApplicationRC Cars, Fixed-wing, Copters, Helicopters
MaterialPlastic (ABS)
Power SourceNo Battery Included (External power required)
Recommended Age14+ years
OriginMainland China
Approx. Dimensions (L x W x H)10 cm x 10 cm x 10 cm
Approx. Weight0.05 kg

10. User Tips

  • Transmitter Compatibility: This receiver is known to work well with the Turnigy 9X transmitter, in addition to other FlySky 2.4Ghz GFSK compatible transmitters.
  • Antenna Placement: For optimal range and signal integrity, ensure the receiver antenna is positioned as straight as possible and away from any carbon fiber or metallic components of your model.

11. Warranty and Support

For any issues or questions regarding your FlySky FS-R9B receiver, please contact the seller or manufacturer's support channels. Keep your purchase receipt as proof of purchase for warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.