EPever LS1012EU/LS1024EU

Contents

EPEVER LandStar LS-EU Series PWM Solar Charge Controller User Manual

Models: LS1012EU, LS1024EU

Brand: EPEVER

1. Product Overview

The EPEVER LandStar LS-EU series is a reliable, stable, and economical solar charge controller designed for various solar power system applications. Building upon the LS-E series, the LS-EU models feature an additional 5V/1.2A USB terminal output, enabling convenient charging for mobile phones, DC fans, and other small electronic devices.

This controller utilizes advanced Pulse Width Modulation (PWM) technology for efficient battery charging and management.

Key Features:

  • 3-stage intelligent PWM charging: Bulk, Boost/Equalize, Float.
  • Supports 3 battery charging options: Sealed, Gel, and Flooded.
  • Battery status LED indicator for clear battery situation monitoring.
  • Battery temperature compensation function for optimized charging.
  • User-friendly settings for comfortable and convenient operation.
  • Integrated 5V/1.2A USB output for charging electronic devices (LS-EU series only).
  • Configurable battery type and load output via a single button.
  • Extensive electronic protection features.
Overview and features of EPEVER LandStar E/EU series solar charge controller
Figure 1: Overview and key features of the LandStar E/EU series.
EPEVER LS-EU series 10A PWM Solar Charge Controller
Figure 2: EPEVER LS-EU series 10A PWM Solar Charge Controller.

2. Component Identification

Familiarize yourself with the various components and indicators of your solar charge controller:

Labeled components of EPEVER LS-EU series solar charge controller
Figure 3: Labeled components of the EPEVER LS-EU series controller.
Table 1: Component Descriptions
No.ComponentDescription
1PV TerminalsConnects to solar panel array.
2Battery TerminalsConnects to battery bank.
3Load TerminalsConnects to DC loads.
4USB output interface5V Max. 1.2A output for charging (LS-EU series only).
5Mounting Hole Φ4.5For securing the controller to a surface.
6Load Switch ButtonControls the DC load output.
7Battery status LED indicatorIndicates battery charge level and status.
8Load status LED indicatorIndicates load output status (ON/OFF, Over Load, Short-circuit).
9Charging status LED indicatorIndicates PV charging status (Charging, Overvoltage).

3. Installation and Setup

3.1 Mounting the Controller

  • Choose a dry, well-ventilated location away from direct sunlight and heat sources.
  • Ensure adequate air circulation around the controller for proper heat dissipation.
  • Mount the controller vertically on a wall or other stable surface using the provided mounting holes (Φ4.5).

3.2 Wiring Connections

Important Safety Note: Always connect the battery first, then the solar panel, and finally the load. Disconnect in the reverse order. Ensure all connections are secure and correct polarity is observed to prevent damage to the controller or other components.

Wiring diagram for EPEVER LS-EU series solar charge controller
Figure 4: Wiring diagram showing connections for solar panel, battery, and load.
Simplified wiring diagram for EPEVER solar charge controller
Figure 5: Simplified wiring diagram for a basic solar setup.
  1. Connect the Battery: Connect the positive and negative terminals of the battery to the corresponding battery terminals on the controller (labeled '2' in Figure 3). Ensure correct polarity.
  2. Connect the Solar Panel: Connect the positive and negative terminals of the solar panel to the corresponding PV terminals on the controller (labeled '1' in Figure 3). Ensure correct polarity.
  3. Connect the DC Load: Connect the positive and negative terminals of your DC load to the corresponding load terminals on the controller (labeled '3' in Figure 3). Ensure correct polarity.
  4. USB Output: The USB port (labeled '4' in Figure 3) can be used to charge 5V electronic devices.

Note: It is recommended to install appropriate breakers and fuses between the components for safety and protection against overcurrents.

4. Operation

4.1 LED Indicators

The controller features several LED indicators to display the system's status:

  • Charging Status LED (9): Indicates if the solar panel is charging the battery and if there's an overvoltage condition.
  • Load Status LED (8): Shows the status of the DC load output (ON, OFF, Over Load, Short-circuit).
  • Battery Status LED (7): Displays the current charge level of the battery.
LED indicators on EPEVER LS-EU series solar charge controller
Figure 6: Location of LED indicators.

4.2 Setting Battery Type and Load Output

The controller allows you to select the battery type and control the load output using the Load Switch Button (6).

  1. Battery Type Selection:
    • Enter setting mode by long pressing the Load Switch Button for 5 seconds.
    • Short press the button to cycle through the desired battery types (Sealed, Gel, Flooded).
    • The selected mode will be saved automatically if no operation occurs for 5 seconds, and the LED will stop flashing.
  2. Load Output Control:
    • Short press the Load Switch Button to turn the DC load output ON or OFF.

5. Maintenance

To ensure optimal performance and longevity of your EPEVER solar charge controller, regular maintenance is recommended:

  • Clean Terminals: Periodically check and clean all terminals to ensure good electrical contact and prevent corrosion.
  • Inspect Wiring: Verify that all wiring connections are secure and free from damage.
  • Check Ventilation: Ensure the controller's ventilation openings are not obstructed to allow for proper heat dissipation.
  • Monitor Indicators: Regularly observe the LED indicators for any abnormal status that might suggest a problem.
  • Battery Health: Monitor your battery's health and ensure it is compatible with the selected charging parameters.

6. Troubleshooting

This section provides guidance on common issues you might encounter with your solar charge controller.

Table 2: Common Troubleshooting Scenarios
ProblemPossible CauseSolution
No charging (PV LED off)No solar input, reversed PV polarity, PV short-circuit.Check solar panel connection, ensure sufficient sunlight, verify PV polarity.
Load not working (Load LED off)Load switch OFF, battery low voltage, load overcurrent/short-circuit.Press load switch button, check battery voltage, reduce load, check for short-circuits.
Battery not charging fullyIncorrect battery type setting, insufficient solar power, aging battery.Verify battery type setting, ensure adequate solar panel size and sunlight, consider battery replacement.
Controller overheatingPoor ventilation, excessive load.Ensure proper airflow around the controller, reduce load if consistently overheating.

7. Technical Specifications

The following table details the technical specifications for the LandStar E/EU series solar charge controllers:

Technical specifications table for EPEVER LandStar E/EU series solar charge controllers
Figure 7: Detailed technical specifications for various models in the LandStar E/EU series.
Table 3: LS1012EU / LS1024EU Specifications
ParameterLS1012EU (12V)LS1024EU (12/24V Auto)
Nominal system voltage12VDC12/24VDC Auto
Rated charge current10A10A
Rated discharge current10A10A
Battery input voltage range8V ~ 16V8V ~ 32V
Max. PV open circuit voltage30V50V
Self-consumption≤5mA (12V)≤5mA (12V), ≤7mA (24V)
Charge Circuit Voltage Drop≤0.21V≤0.21V
Discharge Circuit Voltage Drop≤0.12V≤0.12V
USB output interface5VDC/1.2A
Temperature compensation coefficient-3mV/°C/2V
Working environment temperature-35°C ~ +55°C
Humidity≤95% (N.C.)
EnclosureIP30IP30
Overall dimension101.2x67.0x22.2mm101.2x67.0x22.2mm
Mounting dimension84.6mm84.6mm
Mounting hole sizeΦ4.5
Terminals mm²14AWG/2.514AWG/2.5
Net weight0.07kg0.07kg

8. User Tips

  • For optimal battery life, ensure the correct battery type (Sealed, Gel, or Flooded) is selected in the controller settings.
  • When connecting, always double-check the polarity of the solar panels, battery, and load to prevent damage.
  • The USB output is convenient for small devices but remember its maximum current is 1.2A.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the manufacturer, EPEVER, or your authorized dealer. Keep your purchase receipt as proof of purchase.

10. Video Guide

Watch this video for an unboxing and overview of the EPEVER LS0512EU solar charge controller, demonstrating its physical features and basic operation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.