Flysky FS-T6

Contents

Flysky FS-T6 2.4GHz 6CH Transmitter and R6-B Receiver User Manual

Model: FS-T6 | Brand: Flysky

Flysky FS-T6 Transmitter and R6-B Receiver

Figure 1: Flysky FS-T6 Transmitter and R6-B Receiver included in the package.

Introduction

The Flysky FS-T6 is a sophisticated 6-channel 2.4GHz radio control system designed for a wide range of RC aircraft, including gliders, helicopters, and airplanes. This system incorporates Flysky's advanced Automatic Frequency Hopping Digital System (AFHDS) technology, ensuring reliable and interference-free communication between the transmitter and receiver. With its user-friendly interface, backlit LCD screen, and capacity to store up to 20 different model configurations, the FS-T6 offers both power and convenience for sport modelers.

Setup

1. Unpacking and Inspection

Carefully unpack all components and inspect them for any signs of damage. The package should include:

  • 1 x FS-T6 2.4G 6ch transmitter
  • 1 x FS 6ch receiver (R6-B)
  • 1 x User Manual (this document)
FS-T6 Transmitter, R6-B Receiver, and CD

Figure 2: Package contents including the transmitter, receiver, and a software CD.

2. Transmitter Battery Installation

The FS-T6 transmitter requires 8 AA batteries (1.5V each) for a total of 12V DC power. Ensure correct polarity when inserting batteries.

  1. Open the battery compartment cover located on the back of the transmitter.
  2. Insert 8 AA batteries, observing the polarity markings inside the compartment.
  3. Close the battery compartment cover securely.
FS-T6 Transmitter with battery compartment open

Figure 3: Rear view of the FS-T6 Transmitter with the battery compartment open for installation.

3. Receiver Connection (R6-B)

Connect the R6-B receiver to your model's electronic speed controller (ESC) and servos. Refer to your model's specific wiring diagram for proper connections. The receiver has 6 channels, labeled CH1 to CH6, and a B/VCC port for binding/power.

Close-up of the R6-B 6-channel receiver

Figure 4: Close-up view of the R6-B 6-channel receiver with labeled ports.

4. Binding the Transmitter and Receiver

To establish communication, the transmitter and receiver must be bound:

  1. Ensure the transmitter is powered off.
  2. Connect the bind plug (included) to the B/VCC port on the R6-B receiver.
  3. Apply power to the receiver (e.g., via ESC or separate battery). The receiver's LED should flash rapidly.
  4. While holding down the 'BIND KEY' button on the back of the FS-T6 transmitter, power on the transmitter.
  5. Release the 'BIND KEY' button once the transmitter's screen illuminates.
  6. The receiver's LED should now be solid, indicating a successful bind.
  7. Power off both the receiver and transmitter. Remove the bind plug from the receiver.
  8. Power on the transmitter first, then the receiver. The receiver's LED should be solid, confirming the connection.
Rear view of the FS-T6 Transmitter showing the BIND KEY

Figure 5: Location of the 'BIND KEY' button on the back of the FS-T6 Transmitter.

R6-B receiver with binding plug connected

Figure 6: R6-B receiver with the binding plug inserted into the B/VCC port.

5. Mode Selection (Mode 1 / Mode 2)

The FS-T6 transmitter is available in two modes:

  • Mode 1 (Right Hand): Throttle on the right stick.
  • Mode 2 (Left Hand): Throttle on the left stick.

Ensure you have the correct mode for your flying preference. The mode is typically set at the factory and may require internal modification or professional service to change.

Operating Instructions

1. Powering On/Off

To power on the transmitter, slide the power switch located on the front panel. The backlit LCD screen will illuminate. To power off, slide the switch back to the OFF position.

Front view of the FS-T6 Transmitter with screen

Figure 7: Front view of the FS-T6 Transmitter, showing the power switch and LCD screen.

2. Basic Controls

The FS-T6 features 6 channels for controlling various functions of your RC model. The primary controls are on the two gimbals (joysticks) and various switches and potentiometers.

  • Gimbals: Control primary flight surfaces (throttle, aileron, elevator, rudder) depending on the selected mode.
  • Switches (VRA, VRB, SWA, SWB, SWC, SWD): Used for auxiliary functions such as flaps, landing gear, flight modes, etc.
  • Trims: Fine-tune the neutral position of control surfaces.
Close-up of the top controls and switches on the FS-T6 Transmitter

Figure 8: Top view of the FS-T6 Transmitter showing gimbals, switches, and trims.

3. Programming and Menu Navigation

The FS-T6 features an intuitive programming interface via its backlit LCD screen and a click-and-scroll dial. This allows for quick and easy menu navigation and parameter adjustment.

Close-up of the LCD screen and navigation buttons on the FS-T6 Transmitter

Figure 9: Detailed view of the FS-T6 LCD screen and navigation controls.

Key programming features include:

  • Model Memory: Store up to 20 different model configurations.
  • Throttle Curves: Adjust throttle response for different flight phases.
  • Expo (Exponential): Soften control response around the stick center for smoother flying.
  • End Points: Set the maximum travel for each servo.
  • Sub-Trims: Electronically adjust servo center points.
  • Reverse: Reverse servo direction.

Many programming functions are graphically depicted on the LCD screen, providing a clear visual representation of the changes being made.

4. AFHDS 2.4GHz System

The Automatic Frequency Hopping Digital System (AFHDS) provides several advantages:

  • Anti-Jamming Capability: Equipped with super active and passive anti-jamming features.
  • Low Power Consumption: Efficient operation for extended battery life.
  • High Receiver Sensitivity: Ensures reliable signal reception.
  • Interference Elimination: Operates outside the frequency range of other electronic components in your model, reducing glitches and interference common with traditional radio systems.

Maintenance

1. Battery Care

  • Always remove AA batteries from the transmitter if it will not be used for an extended period to prevent leakage and damage.
  • Use high-quality alkaline or rechargeable AA batteries.
  • Monitor the low voltage warning (9V) and replace/recharge batteries promptly.

2. Cleaning and Storage

  • Clean the transmitter and receiver with a soft, dry cloth. Avoid using solvents or harsh chemicals.
  • Store the system in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Protect the gimbals and switches from dust and physical impact.

3. Antenna Care

  • Ensure the transmitter antenna is fully extended during operation for optimal range and signal strength.
  • Avoid bending or stressing the antenna.
FS-T6 Transmitter with antenna extended

Figure 10: FS-T6 Transmitter with its antenna in the extended position.

Troubleshooting

Problem Possible Cause Solution
Transmitter does not power on. Dead or incorrectly installed batteries. Check battery polarity and replace with fresh batteries.
Receiver LED is not solid after powering on. Not bound to transmitter, or transmitter is off. Ensure transmitter is on. Re-perform the binding procedure.
Model controls are unresponsive or erratic. Low transmitter battery voltage, interference, or incorrect servo connections. Check transmitter battery voltage (warning at 9V). Verify all servo connections. Ensure no strong 2.4GHz interference sources nearby.
Low Voltage Warning (9V) appears on screen. Transmitter batteries are low. Replace or recharge transmitter batteries immediately.

Specifications

Feature Detail
Channels 6 Channels
Model Type Glider/Heli/Airplane
RF Range 2.40-2.48GHz
Bandwidth 500Hz
Band 160
RF Power Less Than 20dBm
2.4GHz System AFHDS (Automatic Frequency Hopping Digital System)
Code Type GFSK
Sensitivity 1024
Low Voltage Warning 9V
DSC Port PS2; Output: PPM
Charger Port Yes
Power 12V DC (8 x 1.5V AA Batteries)
Weight 590g
Antenna Length 26mm
Dimensions (LxWxH) 302x190x93mm
Color Black/Silver
Certificates CE, FCC
Material Metal (internal components)
Recommended Age 14+ years

User Tips

  • Start Simple: If you are new to programmable transmitters, begin by setting up a basic model with minimal mixing. Gradually introduce more advanced features as you become comfortable.
  • Practice on a Simulator: Before flying your actual model, practice with a flight simulator using your FS-T6 transmitter connected via the DSC port. This helps build muscle memory and familiarity with the controls.
  • Regular Range Checks: Always perform a range check before each flight session to ensure reliable communication between the transmitter and receiver.
  • Backup Model Settings: For complex models, consider noting down or backing up your programming settings. While the FS-T6 stores 20 models, having a physical record can be helpful.
  • Keep Firmware Updated: Check the official Flysky website periodically for any firmware updates that might improve performance or add new features.

Warranty and Support

The Flysky FS-T6 system is designed and manufactured to high standards, evidenced by its CE and FCC certifications. For any technical support, troubleshooting beyond this manual, or warranty inquiries, please contact the seller or the official Flysky support channels. Keep your purchase receipt as proof of purchase for warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.