FlySky FS-i6

Contents

FlySky FS-i6 2.4G 6CH AFHDS RC Transmitter User Manual

Model: FS-i6 | Brand: FlySky

1. Introduction

The FlySky FS-i6 is a 6-channel 2.4G AFHDS (Automatic Frequency Hopping Digital System) radio control transmitter designed for various remote-controlled models, including airplanes, helicopters, UAVs, and multicopters. This manual provides essential information for the safe and effective setup, operation, and maintenance of your FS-i6 transmitter.

FlySky FS-i6 Transmitter with various compatible receivers
FlySky FS-i6 Transmitter with various compatible receivers (FS-A8S, FS-iA6B, FS-iA6).

2. Safety Information

Always operate your RC equipment responsibly. Failure to do so may result in injury or damage to property. Observe the following precautions:

  • Ensure all batteries are fully charged before operation.
  • Never operate your RC model in crowded areas, near power lines, or in adverse weather conditions.
  • Perform a range check before each flight or operation.
  • Keep the transmitter and receiver away from moisture and extreme temperatures.
  • Always turn on the transmitter first, then the receiver. When powering off, turn off the receiver first, then the transmitter.

3. Package Contents

Depending on the specific variant purchased, your package may include:

  • FlySky FS-i6 2.4G 6CH AFHDS RC Transmitter
  • Compatible Receiver (e.g., FS-iA6, FS-iA6B, X6B, R6B, A8S, iA10B, FS2A) - Note: Some packages may include the transmitter only.
  • Retail Box
FlySky FS-i6 Transmitter packaged with its retail box
FlySky FS-i6 Transmitter packaged with its retail box, indicating the 'Mode 2 (left hand)' configuration and 'NO RECEIVER' for this specific option.

4. Specifications

FeatureSpecification
Model NumberVZEU0588
Channels6CH
Frequency2.4G (AFHDS)
Size174 x 89 x 190 mm
MaterialMetal
Power SourceNo Battery (requires user-supplied AA batteries)
For Vehicle TypeAirplanes, Heli, UAV, Multicopter, Drone
Recommended Age14+ years
OriginMainland China

5. Setup

5.1. Battery Installation

  1. Open the battery compartment cover on the back of the transmitter.
  2. Insert 4 AA batteries, ensuring correct polarity.
  3. Close the battery compartment cover securely.
Rear view of the FlySky FS-i6 Transmitter with open battery compartment
Rear view of the FlySky FS-i6 Transmitter with the battery compartment open, showing space for AA batteries.

5.2. Binding Transmitter and Receiver

To establish communication between the transmitter and receiver, they must be bound. The exact procedure may vary slightly depending on the receiver model, but generally involves:

  1. Ensure the transmitter is powered off.
  2. Connect the bind plug to the B/VCC port on the receiver.
  3. Power on the receiver (e.g., connect to a flight controller or external power source). The receiver's LED should flash rapidly.
  4. Press and hold the 'BIND KEY' button on the FS-i6 transmitter while powering it on.
  5. The transmitter's LCD screen will display 'Binding...' or similar. The receiver's LED should become solid, indicating successful binding.
  6. Release the 'BIND KEY' button on the transmitter.
  7. Power off both the receiver and transmitter.
  8. Remove the bind plug from the receiver.
  9. Power on the transmitter first, then the receiver. The receiver's LED should now be solid, indicating a successful connection.

5.3. Mode Selection (Mode 1 / Mode 2)

The FS-i6 transmitter supports both Mode 1 and Mode 2 configurations, which define the throttle stick's position:

  • Mode 1: Throttle control is on the right stick.
  • Mode 2: Throttle control is on the left stick (most common in North America).

Your transmitter's mode is typically indicated on the packaging or in the product description. The physical stick configuration (e.g., spring-loaded vs. friction throttle) can often be adjusted internally if needed.

6. Operating Instructions

6.1. Powering On/Off

  • To Power On: Press and hold the 'POWER' button until the LCD screen illuminates.
  • To Power Off: Press and hold the 'POWER' button until the screen turns off.

6.2. Basic Controls

The FS-i6 features two main control sticks, several switches, and rotary knobs:

  • Control Sticks: Used for primary flight/movement control (e.g., throttle, aileron, elevator, rudder).
  • Switches (SW A, B, C, D): Typically used for activating flight modes, gear, flaps, or other auxiliary functions.
  • Rotary Knobs (VR A, B): Provide proportional control for functions like camera tilt, gain adjustment, or other auxiliary channels.
Front view of the FlySky FS-i6 6-channel RC Transmitter
Front view of the FlySky FS-i6 6-channel RC Transmitter, showing the LCD screen and control sticks.

6.3. LCD Display

The LCD screen provides real-time information, including:

  • Transmitter voltage
  • Active channels
  • Model memory selection
  • Trim settings
  • Binding status

6.4. Range

The typical control range for the FlySky FS-i6 system is approximately 500 to 1000 meters, though some users report effective ranges around 250 meters depending on environmental factors and receiver type. Always perform a range check in your operating environment to ensure safe control.

6.5. Video Overview

Official product overview of the FlySky FS-i6 2.4G 6CH AFHDS RC Transmitter.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the transmitter. Avoid using solvents or abrasive cleaners.
  • Storage: Store the transmitter in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
  • Battery Care: Replace AA batteries when the low voltage warning appears on the LCD. Do not mix old and new batteries or different types of batteries.

8. Troubleshooting

  • Transmitter not powering on: Check battery installation and ensure batteries are charged.
  • No connection to receiver: Re-perform the binding procedure. Ensure the receiver is powered correctly.
  • Limited range: Check antenna orientation on both transmitter and receiver. Avoid operating near sources of interference (e.g., Wi-Fi routers, metal structures).
  • Unresponsive controls: Verify that the receiver is correctly connected to your model's flight controller or servos. Check for proper binding.

9. User Tips

  • The FS-i6 can be connected to a computer for programming and use with flight simulators, often requiring a separate USB adapter cable.
  • While a 6-channel system is suitable for many models, advanced users flying quadcopters or other complex models might consider flashing the firmware to support 10 or 14 channels if compatible with their receiver and model.
  • The FS-i6 is versatile and has been successfully used for various applications, including fishing boats.
  • Be aware of your transmitter's mode (Mode 1 or Mode 2) as it dictates the throttle stick's position.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official FlySky website or contact your retailer. Keep your proof of purchase for any warranty claims.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.