LYZRC L200 PLUS MAX

Contents

L200 PLUS MAX / L200 PLUS Drone User Manual

Model: L200 PLUS MAX / L200 PLUS

Brand: LYZRC

1. Introduction

This manual provides essential information for the safe operation and maintenance of your L200 PLUS MAX or L200 PLUS drone. Please read it thoroughly before your first flight to ensure proper usage and to maximize your flying experience.

2. Safety Guidelines

WARNING: For recreation use only. Illegal modification of drones is prohibited. Always comply with local laws and regulations regarding drone usage.

General Safety Precautions:

  • Fly in a safe, open area, away from people, pets, power lines, trees, and buildings.
  • Avoid flying in extreme weather conditions such as high heat, extreme cold, strong winds (above level 4), or rain.
  • Do not disassemble the product. Improper use can lead to damage or injury.
  • The product is suitable for individuals aged 12 and above. Beginners are advised to practice at low altitudes in open, uninhabited areas for approximately three days to become familiar with the controls, preferably under the guidance of an experienced pilot.

During Operation:

  • Do not touch the fast-spinning propellers after starting the aircraft. Maintain a safe distance to prevent entanglement (including gears, rotors, etc.).
  • The battery and motor may become hot during and after use. Avoid direct contact to prevent burns.
  • Do not look directly into the LED indicator lights to protect your eyes.

Disclaimer:

The manufacturer is not responsible for any damage or injury caused by improper use or disassembly of the product.

3. Package Contents

Please check the contents of your package against the list below. If any parts are missing, please contact your retailer with your purchase receipt for replacement.

  • Drone (L200 PLUS MAX / L200 PLUS) x 1 (Battery included)
  • Remote Controller x 1
  • USB Charging Cable x 1
  • Spare Propeller Blades x 8
  • User Manual x 1
  • Screwdriver x 1
  • Storage Bag x 1
  • Color Box x 1
  • Obstacle Avoidance Device x 1 (Only for L200 PLUS MAX version)
  • Lens Cap x 1
  • Mobile Phone Holder x 1
  • Spare Screw x 4
  • Memory Card / Card Reader x 1
L200 PLUS drone with remote control, phone holder, and various accessories including spare propellers, screwdriver, USB cable, and battery.

Figure 3.1: L200 PLUS Drone and Accessories

4. Specifications

FeatureSpecification
ModelL200 PLUS MAX / L200 PLUS
Quadcopter Weight249g
Motor Type1503 Brushless Motor
Gimbal3-Axis Mechanical Stabilization + Electronic Stabilization and Anti-Shake
Front Camera Photo Resolution4096*3072P
Front Camera Video Resolution2048*1080P
Bottom Camera Photo Resolution1280*720P
Bottom Camera Video Resolution1280*720P
Electric Adjustment Camera Angle110°
Camera Wide Angle120°
Obstacle Avoidance360° Intelligent Obstacle Avoidance (Optional, available on PLUS MAX version)
Control Channels4 Channels
Gyro6 Axis
Remote Control Frequency2.4GHz
Smartphone Receiving Method5G WIFI Channel
Remote Control DistanceApprox. 3000 Meters (No Interference, No Occlusion)
WIFI Transmission DistanceApprox. 3000 Meters (No Interference, No Occlusion)
Drone Battery7.4V/3800mAh Lithium Battery
Flight TimeApprox. 28-30 Minutes
Drone Charging TimeApprox. 6 Hours
Remote Control Battery3.7V/400mAh Lithium Battery
Remote Control Charging TimeApprox. 40 Minutes
Frame Rate25 fps
Photo Recording ModeRemote Control + APP Control
Quadcopter Size (Unfolded)35*35*10cm
Quadcopter Size (Folded)9*15.5*10cm
Max Wind Speed Resistance< 10 KM/H
Max Takeoff Weight<1kg
Expandable StorageYes, up to 32GB SD card
APP Supported LanguagesEnglish, Simplified Chinese
Sensing TypeComplete Omnidirectional (for obstacle avoidance)
GPSYes
Aerial PhotographyYes
CertificationCE
Drone dimensions showing unfolded size of 35x35x10cm and folded size of 9x15.5x10cm.

Figure 4.1: Drone Size Display (Unfolded and Folded)

5. Setup Guide

5.1. Charging the Remote Control

  1. Connect the USB charging cable to the remote control's charging port.
  2. Connect the other end of the USB cable to a computer or a mobile phone charger.
  3. The charging indicator light will illuminate during charging and turn off when fully charged.

Note: Charging time is approximately 40 minutes. If the charging indicator does not change, the battery is fully charged and does not need further charging.

Diagram showing how to connect the remote control to a USB power source for charging.

Figure 5.1: Remote Control Charging

5.2. Charging the Drone Battery

  1. To remove the drone battery, press the indicated position (Figure 5.2) and pull the battery backward.
  2. Connect the USB-Android head of the charging cable to the battery.
  3. Connect the USB plug to a computer or a mobile phone charger.
  4. The battery indicator will light up during charging and turn off when fully charged.

Note: Charging time is approximately 360 minutes (6 hours). If the indicator light on the battery does not illuminate when connected to the charger, the battery does not need charging.

Diagram showing how to remove the drone battery and connect it to a USB charging cable.

Figure 5.2: Drone Battery Removal and Charging

5.3. Installing the Obstacle Avoidance Device (L200 PLUS MAX only)

  1. Remove the cover plate from the installation slot of the obstacle avoidance device.
  2. Insert the obstacle avoidance device's plug into the drone's port as shown in the figure, then load the device onto the drone.

WARNING: Ensure correct installation. Incorrect installation may prevent proper flight.

Diagram showing the installation of the obstacle avoidance device on the drone.

Figure 5.3: Obstacle Avoidance Device Installation

5.4. Remote Control Overview

Diagram of the remote control with labels for each button and joystick function.

Figure 5.4: Remote Control Layout and Functions

Key Functions:

  • Left Joystick: Controls altitude (up/down) and yaw (left/right rotation).
  • Right Joystick: Controls forward/backward, left/right flight.
  • Power Switch: Turns the remote control on/off.
  • Speed Switch: Adjusts flight speed.
  • Obstacle Avoidance Switch: Toggles obstacle avoidance (disabled by default).
  • GPS Switch: Toggles GPS mode.
  • One-Click Return: Initiates automatic return to home.
  • Gyro Calibration: Press briefly to calibrate gyroscope.
  • Geomagnetic Calibration: Press and hold for geomagnetic calibration.
  • Photo/Video Button: Short press for photo, long press for video.
  • Camera Angle Adjustment: Roller on the remote control.
  • LCD Display: Shows flight status, GPS signal, battery levels, etc.
  • Phone Holder: Pull up to place your smartphone.
  • Data Cable Port: Connects phone to remote control for APP control.
  • Charging Port: For charging the remote control.
  • Memory Card Slot: For inserting an SD card to store photos/videos.

6. Operating Instructions

6.1. Pre-Flight Environment Requirements

For optimal and safe flight, choose an open outdoor area free from rain, snow, or wind stronger than level 4. Ensure there are no people, trees, power lines, tall buildings, airports, or signal towers nearby. For indoor flight, select a spacious, obstacle-free area, preferably without people or pets.

6.2. Basic Flight Steps (Outdoor Mode)

  1. Drone and Remote Control Pairing:
    Insert the drone battery correctly and place the drone on a flat surface. Power on the drone, then power on the remote control. The drone and remote control lights will blink. After approximately 40 seconds, the remote control will emit two beeps, indicating successful pairing.
  2. Gyroscope Calibration:
    Place the drone horizontally and press the "Gyro Calibration" button on the remote control. The drone's lights will blink rapidly and then become solid, and the remote control will emit a "Di" sound, indicating successful calibration.
  3. Geomagnetic Calibration:
    The geomagnetic field can be affected by electronic devices. Perform this calibration for the first time or if flying in a new location.
    a. After pressing the button on the remote control (Figure 6.1), it will emit a "Di" sound, and the drone's indicator light will blink rapidly.
    b. Hold the drone and rotate it slowly three times clockwise in a horizontal direction (Figure 6.2). The remote control will emit a "Di" sound, indicating successful horizontal calibration.
    c. Now, hold the drone with its nose pointing downwards and rotate it slowly three times clockwise in a vertical direction (Figure 6.3). The remote control will emit two "DiDi" sounds, indicating successful vertical calibration.
  4. Diagram showing the drone in horizontal position for gyroscope calibration.

    Figure 6.1: Gyroscope Calibration

    Diagram showing the drone being rotated horizontally for geomagnetic calibration.

    Figure 6.2: Horizontal Geomagnetic Calibration

    Diagram showing the drone being rotated vertically for geomagnetic calibration.

    Figure 6.3: Vertical Geomagnetic Calibration

  5. GPS Signal Acquisition:
    After geomagnetic calibration, place the drone on a flat surface. It will automatically search for satellites. The drone's indicator light will change from slow blinking to solid, and the remote control's outdoor mode indicator will also become solid, indicating successful satellite acquisition. This process usually takes 60-80 seconds (with more than 10 satellites).
  6. Unlocking the Drone:
    Once GPS signal is acquired, short press the "Unlock" button on the remote control. All four propellers will start spinning at the same speed, indicating the drone is unlocked and ready for flight.

6.3. Flight Controls

Diagrams illustrating the effects of moving the left and right joysticks on drone movement.

Figure 6.4: Flight Control Methods

  • Left Joystick Up: Increases main rotor speed, drone ascends.
  • Left Joystick Down: Decreases main rotor speed, drone descends.
  • Left Joystick Left/Right: Rotates the drone's nose left/right (yaw).
  • Right Joystick Up/Down: Moves the drone forward/backward (pitch).
  • Right Joystick Left/Right: Moves the drone left/right (roll).

WARNING: When the drone is within 30 cm of the ground, it may become unstable due to propeller wash, known as "ground effect." The lower the drone, the greater the ground effect.

6.4. Speed Adjustment

The default takeoff speed is slow. While in flight, you can adjust the speed using the speed switch knob on the remote control. Turning the knob right once will make the remote control emit two "Di Di" sounds, indicating the second gear (higher speed) is engaged. Turning it left will return to the first gear (lower speed).

6.5. Camera Angle Adjustment

During flight, the camera angle can be adjusted using the camera adjustment knob on the remote control. Turning the knob left increases the camera angle (tilts up), and turning it right decreases the camera angle (tilts down).

Diagram showing the camera angle adjustment knob on the remote control and its effect on the drone's camera.

Figure 6.5: Camera Angle Adjustment

6.6. Intelligent Flight Modes

Video demonstrating various intelligent flight features including GPS positioning, 3-axis gimbal, long-distance control, 90° electrically adjustable camera, real-time image transmission, long endurance battery, GPS optical flow assisted positioning, omnidirectional intelligent obstacle avoidance, multi-gear speed switching, GPS follow, intelligent surround, night flight indicator light, one-click shooting, night aerial photography, waypoint trajectory flight, and GPS intelligent high-precision return.

  • GPS High-Precision Positioning: The drone uses GPS for accurate positioning, ensuring stable flight.
  • 3-Axis Mechanical Self-Stabilizing Gimbal: Provides stable and clear aerial footage by accurately determining focus and rejecting screen shaking.
  • Long-Distance Control and Flight: Allows for extended range operation and aerial exploration.
  • 90° Electrically Adjustable Camera: Adjust the camera angle during flight for diverse perspectives.
  • Real-Time Image Transmission: View live footage on your smartphone via 5G WIFI.
  • Omnidirectional Intelligent Obstacle Avoidance Mode (L200 PLUS MAX only): The drone can detect and avoid obstacles in 360 degrees, enhancing flight safety.
  • Multi-Gear Speed Switching: Adjust flight speed for different scenarios, from stable hovering to high-speed flight.
  • GPS Follow: The drone automatically follows a designated subject.
  • Intelligent Surround: The drone can orbit a point of interest.
  • Waypoint Trajectory Flight: Plan a flight path with multiple waypoints, and the drone will follow it automatically.
  • One-Click Shooting/Recording: Easily capture photos and videos with a single button press.
  • Night Aerial Photography: High brightness night flight indicator lights and advanced imaging allow for clear night footage.
  • GPS Intelligent High-Precision Return: The drone can automatically return to its takeoff point.

6.7. Return to Home (RTH) Functions

The drone features several Return to Home (RTH) functions to ensure safe retrieval:

  • One-Click RTH: Press the "One-Click Return" button on the remote control. The drone will return to the recorded home point. During this process, you can still control the drone with the joysticks to avoid obstacles. Press the "One-Click Return" button again to cancel RTH.
  • Uncontrolled RTH: If the remote control signal is lost for more than 6 seconds (and GPS signal is good with more than 9 satellites, and the compass is normal), the flight control system will automatically take over and guide the drone back to the recorded home point. If the signal is restored during RTH, you can cancel it by pressing the RTH button.
  • Low Battery RTH: When the battery voltage drops to a low level, the low battery indicator will blink slowly, and the drone will automatically return to the home point at an altitude of 30 meters. If the battery voltage drops below a critical level, the drone will automatically land at the home point.

WARNING:

  • During automatic RTH, the drone cannot avoid obstacles.
  • If the GPS signal is weak or unavailable, the drone cannot perform RTH.
  • If the drone loses satellite signal and remote control signal for more than 6 seconds, it will slowly descend and land in place.

7. Maintenance

  • Propeller Replacement: If propellers are damaged, replace them with new ones from the spare parts kit. Ensure correct propeller type (A or B) is installed on the corresponding motor.
  • Battery Care: Store batteries in a cool, dry place. Do not overcharge or over-discharge. If not used for a long time, charge them to about 50-60% capacity.
  • Cleaning: Use a soft, dry cloth to clean the drone and remote control. Avoid using liquids or solvents.

8. Troubleshooting

ProblemSolution
Drone indicator light blinks rapidly after power on.The drone is in gyroscope detection mode. Place the aircraft on a flat surface.
Drone cannot hover, tips over after takeoff.Place the aircraft on a flat surface and recalibrate the gyroscope.
Drone vibrates strongly.Propellers may be deformed. Replace with new propellers.
Drone cannot be unlocked, control light blinks rapidly.The drone battery voltage is too low. Fully charge the battery.
Drone unstable in strong wind.Wait for wind conditions to improve (wind strength below level 4-5) before flying.
Drone cannot hover, circles constantly.Geomagnetic calibration failed. Recalibrate the geomagnetic field.

9. User Tips

  • Practice Makes Perfect: As noted in the manual, beginners should spend a few days practicing at low altitudes in open, safe areas to get comfortable with the controls.
  • Check GPS Signal: Always ensure a strong GPS signal (more than 10 satellites) before taking off, especially when planning to use return-to-home or intelligent flight modes.
  • Extra Batteries: For longer flight sessions, consider purchasing additional batteries as the flight time is approximately 28-30 minutes per charge.
  • Obstacle Avoidance: While the L200 PLUS MAX features 360° obstacle avoidance, it's still crucial to fly cautiously and be aware of your surroundings, especially in complex environments.
  • SD Card: Remember to insert an SD card (up to 32GB) to save your high-quality photos and videos directly to the drone.

10. Frequently Asked Questions

Q: What is the flight time of the drone?

A: The drone has a flight time of approximately 28-30 minutes on a full charge.

Q: Does this drone have obstacle avoidance?

A: The L200 PLUS MAX version features 360° intelligent obstacle avoidance. The L200 PLUS version does not.

Q: What is the maximum control distance?

A: The remote control distance and WIFI transmission distance are both approximately 3000 meters in an open area without interference.

Q: Can I use an SD card with this drone?

A: Yes, the drone supports an SD card up to 32GB for storing photos and videos.

Q: How long does it take to charge the drone battery?

A: The drone battery takes approximately 6 hours to fully charge.

11. Warranty and Support

For any issues, technical support, or warranty claims, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific warranty terms and contact information.

A user manual in PDF format is available for download. Please refer to the seller's product page or contact support for the link: User manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.