LYZRC L200 Plus

Contents

LYZRC L200 Plus GPS Drone User Manual

Model: L200 Plus

1. Safety Information and Warnings

⚠️ WARNING: CHOKING HAZARD - small parts. Not for children under 3 years.

This product is not suitable for use by people under the age of 14. Children should be guided by adults when operating the aircraft. It is your responsibility to ensure that this aircraft does not cause harm to the personal and property of others.

General Safety Guidelines:

  • The debugging and installation of the aircraft must strictly follow the operation manual.
  • Maintain a safe distance of 2 meters away from the user or others during flight and landing to avoid collisions.
  • Our company and the seller are not responsible for any loss, damage, or bodily injury caused by improper use or operation.
  • Follow instructions for proper installation and use. Some parts should be assembled by adults.
  • The product contains small parts; keep them out of reach of children to prevent accidental ingestion or suffocation.
  • Do not play on the road or in areas with accumulated water.
  • Pack packaging materials in a timely manner to avoid harm to children.
  • Do not disassemble or modify the aircraft, as this may cause malfunction.
  • The charger battery box battery needs to be inserted into a designated power source that matches the product logo.
  • The remote control uses a 3.7V built-in lithium battery, which does not require replacement.
  • Regularly check if charging line components are damaged. Stop using if damaged until repaired.
  • When charging rechargeable batteries, adult supervision is required. Keep away from high temperatures and flammable materials.
  • Do not short-circuit or squeeze the battery to avoid explosion.
  • Do not mix different types of lithium batteries.
  • The aircraft uses a 7.6V intelligent lithium battery. Remove it from the plane and charge it.
  • Do not short-circuit, disassemble, or throw the battery into fire. Do not place the battery in a hot or heated area.
  • Exhausted batteries should be removed from the model.
  • The power terminal should not be short-circuited.
  • During flight, stay away from other electrical equipment and environments with magnetism and magnetic fields, as this may interfere with the aircraft's magnetic sensors.
  • Maintain a safe distance from the high-speed rotating propeller to avoid the risk of twisting or cutting.
  • The motor is a heating component; do not touch it immediately after use to avoid burns.
  • Light emitting diode laser radiation; keep your eyes away from the beam.
  • Do not use the model close to the ear; misuse may cause hearing damage.
  • Charging line: 5V = 1-2A.

Flight Environment Restrictions:

  • Avoid flying over or near people, trees, high-voltage power lines, buildings, airports, or water areas.
  • Do not use this product under adverse weather conditions such as rain, snow, fog, and wind speeds exceeding 7m/s or 16mph.
  • Stay away from rotating propellers and motors.
  • It is prohibited to operate within a range of 10 kilometers on both sides of the airport runway centerline and 20 kilometers on both ends of the runway, as well as civil aviation routes and routes.
  • Stop using various models and drones in prohibited flight zones issued by relevant national departments.
  • It is prohibited to use various model remote controls in an area with a radius of 5000 meters centered around the center point of the airport runway.

Disclaimer: For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.

2. Product Overview

The LYZRC L200 Plus is a professional 4K HD dual-lens GPS drone featuring a 3-axis mechanical self-stabilizing gimbal, EIS anti-shake technology, and 360° laser obstacle avoidance. Designed for both beginners and enthusiasts, it offers stable flight and high-quality aerial photography.

Key Features:

  • 249g Body Weight: No registration required in most countries.
  • 3-Axis Mechanical Gimbal + EIS Anti-Shake: Ensures stable and clear photos/videos.
  • 360° Laser Obstacle Avoidance: Detects obstacles within 20 meters for safer flight.
  • Dual GPS/GLONASS Positioning: Provides precise positioning and intelligent return functions.
  • Long Flight Time: Up to 25 minutes with a 7.4V 3800mAh smart lithium battery.
  • Foldable & Portable Design: Compact for easy transport.
  • 4K HD Camera: 110° electric adjustable camera with 5x digital zoom.
  • 5G WiFi Image Transmission: Real-time viewing of aerial footage.
  • Intelligent Flight Functions: Tap flight, point surround, GPS follow, image follow, gesture shooting.
  • Brushless Motor: 1503 (2100/KV) brushless motor for powerful and quiet flight.

Aircraft Components:

  1. 3-axis pan head
  2. Propeller
  3. Motor
  4. LED lights
  5. Intelligent lithium battery
LYZRC L200 Plus GPS Drone with 3-axis gimbal and obstacle avoidance sensor
The LYZRC L200 Plus GPS Drone with its key features highlighted.
Package contents of LYZRC L200 Plus drone including drone, remote, battery, blades, tools, and manual
Package contents: Drone, Obstacle device, Lens cap, Remote control, Mobile phone holder, Fuselage battery, USB charging cable, Screwdriver, Spare fan blade (x8), Spare screw (x4), Instruction Manual, Storage bag, Color box.

3. Setup

3.1 Propeller Installation

Ensure all propellers are installed in the correct orientation (A/B distinction). Incorrect installation will prevent normal flight.

Diagram showing correct propeller installation for drone
Propeller installation diagram. Ensure correct A/B orientation.

3.2 Battery Installation/Removal

Installation: Insert the battery into the aircraft battery compartment in the direction shown by arrow 3 in the figure. Ensure it is securely in place.

Removal: Press the battery clip (arrow 1) and then remove the battery in the direction of arrow 2.

Diagram showing how to install and remove the drone battery
Battery installation and removal instructions.

3.3 Charging (Aircraft Battery & Remote Control)

Connect the battery to a 5V 1-2A charging adapter using the USB charging cable. The battery indicator light remains on during charging and turns off when fully charged (approx. 4 hours for drone battery, 0.5 hours for remote control). Use an adapter with a 2A charging current for faster charging.

Charging Precautions:

  • Insert the plug correctly.
  • Do not place charged batteries in high temperature areas, near open flames, or electric heating devices.
  • Do not use batteries to strike hard object surfaces.
  • Do not immerse the battery in water. Store in a dry place.
  • Do not leave unattended during charging.
  • Do not disassemble the battery.
  • After flight, charge and store the battery. If not in use, charge at least once every 3 months to prevent excessive discharge.
Diagram showing how to charge the drone battery and remote control
Charging the aircraft battery and remote control.

3.4 Memory Card Installation

The manual mentions installing a memory card. While not explicitly detailed, typically memory cards are inserted into a dedicated slot on the drone. Ensure the card is inserted correctly and securely. The drone supports high-speed 32G SD cards (optional, not included).

4. Operating Instructions

4.1 Preparation Before Takeoff

  • Ensure both the remote control and drone battery are fully charged.
  • Fully extend the drone arms and blades.
  • First, turn on the drone switch, then the remote control switch for frequency comparison.

4.2 Aircraft Code Matching

  1. Press and hold the aircraft power button for 3 seconds to turn it on. Place it horizontally on the ground. The front and rear LED lights will flash for self-inspection.
  2. Turn on the remote control. It will emit a beep. The aircraft's front LED light will become permanently on, and the rear LED light will flash, indicating successful code checking.

Note: If lights flash simultaneously, re-synchronize. Before unlocking, fully unfold the blades.

Diagram showing drone and remote control for code matching
Aircraft code matching operation guide.

4.3 Gyroscope Calibration

After successful frequency alignment, place the aircraft on a flat ground. Briefly press the gyroscope calibration button on the remote control. The front and rear lights will flash faster, then become steady, indicating successful calibration.

Diagram showing gyroscope calibration process
Gyroscope calibration.

4.4 Geomagnetic Correction

When flying outdoors in GPS mode, geomagnetic correction is required for the first flight. After frequency alignment, press and hold the geomagnetic correction button for 2 seconds (remote control will beep).

  1. Lift the aircraft 1 meter above the ground, level with the ground, and rotate it three times clockwise. The remote control will emit a short beep, the rear LED light remains on, and the front LED light flashes. (Horizontal correction completed)
  2. Stand the aircraft upright, perpendicular to the ground, and rotate it three times clockwise. The remote control will emit a long beep, and the front LED light remains on while the rear LED light flashes. (Vertical correction completed)

Note: Geomagnetic correction must be completed in both horizontal and vertical directions. Do not calibrate in areas with strong magnetic fields.

Diagram showing geomagnetic correction steps
Geomagnetic correction process.

4.5 Connect WiFi

Enable WiFi on your mobile device, select "VS-GPS-BY-*******" from the list, and open the VS GPS PRO APP. Refer to the APP manual for specific instructions.

4.6 GPS Search Successful

After frequency adjustment, the LED light flashes rapidly. When it stops flashing and becomes permanently on, or the remote control beeps, it indicates that the GPS signal has been acquired, and the drone can be unlocked for takeoff.

Note: Ensure the takeoff environment is open and that satellite signals greater than 10 stars are detected before takeoff. The first search takes approximately 1 to 1.5 minutes.

4.7 Motor Unlocking

Push the throttle lever and direction lever simultaneously towards the lower left and right corners to complete unlocking. After the motor starts, flight can begin.

Diagram showing motor unlocking procedure
Motor unlocking procedure.

4.8 Mode Switching (Indoor/GPS)

Attention: Indoor flight must switch to indoor mode. Outdoor flight must be switched to GPS mode.

  • Indoor Mode: After successful code matching, the aircraft defaults to GPS mode indoors. To take off indoors, first press the GPS switch on the remote control to switch to indoor mode, then unlock and takeoff.
  • GPS Mode: In an outdoor environment, after successful code matching, the aircraft automatically enters search mode. Place it in an open area without obstacles. When the number of satellites reaches about 6, positioning is complete, the remote control beeps, and the arm light stays on for unlocking and takeoff.

Note: Optical flow positioning and hovering may be unstable over water, dim light, large height differences, smooth reflective ground, or bicolor stripes.

4.9 One-Click Takeoff/Landing

  • After unlocking, press and hold the one-key takeoff/landing button for 2 seconds. The aircraft will automatically take off and hover at about 1.5 meters.
  • During flight, press and hold the same button for 2 seconds. The aircraft will automatically land.

4.10 Headless Mode

Press the headless mode button on the remote control. The drone's front direction will be relative to the nose at takeoff, regardless of its orientation during flight.

4.11 Return Flight

The aircraft has a return function. If the return point is successfully recorded (first GPS lock with >10 satellites), the drone can return automatically in three ways:

  1. One-Click Return: When GPS signal is good (>10 satellites), press the return button on the remote control. The drone will return to the recorded point. You can control the drone to avoid obstacles during descent.
  2. No Signal Return: If the remote control signal is interrupted (GPS signal good, >6 satellites, compass normal, return point recorded), the drone will automatically return to the signal location and reconnect.
  3. Low Power Return: When the aircraft battery is low, the indicator light flashes slowly, and the remote control emits a warning sound. The aircraft will automatically return to the takeoff point (approx. 30 meters away).

Precautions for Returning:

  • During automatic return, the aircraft cannot avoid obstacles.
  • If the GPS signal is poor or GPS is not working, return is not possible.
  • In low power return state, the remote control cannot cancel the return.
Diagram showing one-click return button on remote control
One-click return function.

4.12 Photography/Video Recording

  • Short press the photo/video button on the remote control to take a photo. The mobile app will display a progress bar for archiving.
  • Press and hold the photo/video button for 2 seconds to start/stop video recording. The mobile app will display the recording time and save it.
Diagram showing photo and video buttons on remote control
One-click shooting and recording.

4.13 Camera Angle Control

Adjust the shooting angle of the pan-tilt camera by pressing the scroll wheel button on the remote control.

Diagram showing camera angle adjustment on remote control
Camera angle adjustment using the remote control.

4.14 Intelligent Flight Modes

  • Waypoint Trajectory Flight: Plan a custom multi-point route for the drone to follow.
  • GPS Follow: The drone will automatically follow the remote control's GPS position.
  • Intelligent Surround: The drone can orbit a point of interest, with adjustable radius.
  • Gesture Shooting: Make specific gestures within 1-3 meters of the drone to trigger photo or video recording.
Official product video demonstrating flight features like 3-axis gimbal, long-distance flight, real-time transmission, night flight lights, GPS positioning, optical flow positioning, high altitude flight, GPS follow, intelligent surround, waypoint trajectory flight, and GPS return.

5. Maintenance and Upkeep

  • Use genuine parts for maintenance to ensure flight safety.
  • Prevent moisture from entering the aircraft body to avoid mechanical and electronic component failures.
  • Keep the drone away from heat sources and direct sunlight to prevent deformation or damage.
  • Regularly check propellers for damage and replace if necessary.
  • Ensure the camera lens is clean for optimal image quality.
  • Store the drone and accessories in the provided storage bag when not in use.

6. Troubleshooting

  • Drone not taking off/unstable flight:
    • Ensure propellers are installed correctly (A/B orientation).
    • Check if the drone and remote control batteries are fully charged.
    • Verify successful code matching (front LED solid, rear LED flashing).
    • Perform gyroscope calibration.
    • Perform geomagnetic correction, especially for the first outdoor flight in GPS mode.
    • Ensure motors are unlocked by pushing both levers to the lower corners.
    • If flying indoors, ensure indoor mode is selected. If outdoors, ensure GPS mode is selected and sufficient satellites are acquired (>6 for basic flight, >10 for return functions).
    • Avoid flying over reflective surfaces, water, or in dim light when relying on optical flow positioning.
  • Return function not working:
    • Ensure a strong GPS signal (>10 satellites) was acquired at the takeoff point to record the return point.
    • Check GPS status; return is not possible if GPS signal is poor or not working.
    • Remember that during automatic return, the aircraft cannot avoid obstacles.
    • In low power return mode, the return cannot be canceled by the remote control.
  • Obstacle Avoidance: The drone stops when something obstructs its movement but does not actively avoid the obstacle itself. Users must maintain awareness and control.

7. Specifications

Category Details
Product Name L200 Plus MAX
Video Transmission Signal 5G Transmission Signal
Brand Name LYZRC
LYZRC Model L200 PRO MAX
Category Camera Drone
Origin Mainland China
Drone Weight 249g
Expanded Size 35*35*9.3CM
Folding Size 9*15.5*9.3CM
Motor Type Brushless Motor (1503, 2100/KV)
ESC 30A
Aircraf Operating Frequency 2.4 GHz
Max Flight Speed 45 KM/H
Max Ascent Speed 4 M/S
Max Descent Speed 3 M/S
Max Flight Altitude 120M
Max Take-off Altitude 4500M
Max Wind Speed Resistance 20 - 30 KM/H
Flight Time 23-25 Min
Remote Distance 3km (actual 500M)
Camera Integration Camera Included
Camera Mount Type 3-Axis Gimbal
Camera Features 4K HD Video Recording, 110° Electric Adjustable Lens, 5x Digital Zoom
Video Maximum Resolution 4K (4096*2160)
Photo Resolution 4096*3072
Sensor Size 1/4 inches
Aerial Photography Yes
Obstacle Avoidance Types Laser avoidance (360°, Detection Distance: ≤20M)
GPS Yes (Dual GPS/GLONASS)
Connectivity WiFi
Display Control Yes
Integrated Propeller Guard Include
Equipped with Aerosol Spraying System/Spread Tank Volume No
High-concerned chemical None
Drone Battery 7.4V 3800mAh Polymer Lithium Battery
Drone Battery Charging Time Approx. 6 hours
Remote Control Battery 3.7V 400mAh
Remote Control Charging Time Approx. 0.5 hours
Remote Control Endurance Approx. 2 hours
Max Mobile Phone Size (Remote) 7 inches
Charging Method USB 5V charging
Max Charging Power 15.2W
Charging Environment Temperature 5℃ to 40℃
Max Takeoff Weight <1kg
Product parameters table from seller description
Detailed product parameters.
Drone size dimensions in folded and unfolded states
Drone size display.

8. User Tips

  • This drone is highly recommended for beginners due to its stable flight and good camera image quality.
  • The drone is very fast at speed 3, offering an exciting flight experience.
  • GPS acquisition is quick, with users reporting seeing up to 19 satellites.
  • The camera provides good stabilization and is easily controlled.
  • While the drone has obstacle avoidance, it primarily stops when an obstacle is detected rather than actively maneuvering around it. Always be aware of your surroundings.
  • The actual control distance and image transmission distance are around 500M and 300-400M respectively, despite theoretical values being higher. Plan your flights accordingly.
  • Consider purchasing spare batteries for extended flight sessions, as the drone battery life is approximately 25 minutes.
  • An external SD card (up to 32GB, high-speed recommended) is needed for storing footage, as it is not included.

9. Additional Resources

For a comprehensive guide and detailed instructions, please refer to the official PDF user manual:

View User Manual (PDF)

© 2024 LYZRC. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.