1.0 Safety Guidelines
1.1 Check Before Use
This product is a high-precision drone integrating various electronic stability and control mechanisms. Please configure and operate it carefully and correctly to ensure safe, accident-free operation.
- Ensure that the batteries of the drone and transmitter are clean, undamaged, and fully charged before every use.
- Ensure that all propellers are undamaged and installed in the correct orientation.
- Perform a thorough check of the product before each use. Inspect the integrity of parts, any signs of cracks or wear on propellers, battery power, and indicator effectiveness. If any problem is found, refrain from using it until resolved.
1.2 Flight Environment
Always prioritize safety and choose an appropriate environment for flying your drone.
- Fly in Open Areas: Ensure a clear line of sight and avoid obstacles.
- Maintain Line of Sight: Always keep the drone visible during flight.
- Fly Below 98 ft (30 m): Adhere to altitude restrictions for safe operation.
Important Safety Notes:
- Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airports, or bodies of water.
- DO NOT fly near strong electromagnetic sources such as power lines and base stations, as it may affect the onboard compass.
- DO NOT use this drone in adverse weather conditions such as rain, snow, fog, and wind.
2.0 Battery Use and Maintenance
2.1 Use of Battery
- Ensure batteries are fitted in the correct orientation as shown in the instruction manual.
- Avoid short circuits by fitting batteries correctly, and do not crush or squeeze them, as this could cause a fire or explosion.
- DO NOT mix new and old batteries, as this can lead to poor product performance.
- Dispose of used batteries carefully; do not litter and recycle where possible.
- DO NOT expose dead batteries to heat or fire, as they may explode.
- If the device will not be used for an extended period, remove batteries to prevent potential damage from battery leakage.
- Only use the USB charging cable provided with the drone to charge the battery.
- DO NOT connect the battery directly to wall outlets or car cigarette-lighter sockets, as this will damage your battery due to different voltage.
- DO NOT attempt to disassemble or modify the battery in any way.
- DO NOT use the battery if it gives off an odor, generates heat, becomes discolored, deformed, or appears abnormal in any way. If any of these situations occur while the battery is in use or being charged, remove it from the device or charger immediately and discontinue use.
2.2 Maintenance
- Clean the drone after each use with a clean, soft cloth.
- Avoid prolonged exposure to direct sunlight and avoid heat buildup on the drone or batteries.
- This device is not waterproof and must not be submerged or subjected to water under any circumstance. Failure to keep the device completely dry may permanently damage the unit. Be aware that even if it's dry where you are, droplets of rain or mist from a river or waterfall could damage your drone where it is flying.
- Frequently check the charging plug and other accessories for signs of damage. If any part of the device or cables are damaged, avoid using or charging until the damaged parts are replaced.
- Post-Flight Checks:
- Observe the drone for any damage from a potential collision or crash.
- Check to be sure all moving parts, including the propellers, are secure.
- Check the battery for signs of overheating, warping, or swelling. If you notice any abnormality, remove it immediately from the drone.
- Check the levels and efficiency of the power of the battery.
- Clean all lights and ensure they are functioning properly for the next flight.
3.0 Package Contents
The M107 Drone package includes the following items:
| Item | Description | Image |
|---|---|---|
| Drone | 1x M107 Drone with integrated camera | ![]() |
| Transmitter | 1x Remote Control (with or without 4.5-inch screen, depending on version) | ![]() |
| Drone Battery | 1x 3.7V/1000mAh or 3.7V/1800mAh (Modular) Drone Battery | ![]() |
| USB Charging Cable | 1x USB cable for charging drone and remote batteries | ![]() |
| Spare Propellers | 4x Spare Fan Blades (Maple Leaf) | ![]() |
| Screwdriver | 1x Screwdriver for propeller installation | ![]() |
| Instruction Manual | 2x Instruction Books (User Manual) | ![]() |
| Storage Bag (Optional) | 1x Storage Bag for portability | ![]() |
| Gift Box (Optional) | 1x Gift Box | ![]() |
4.0 Drone Details
Familiarize yourself with the different parts of your M107 Drone:

Image: Detailed diagram showing the M107 Drone's propellers (A and B) and camera.
The drone features a foldable design for portability and is equipped with a high-definition camera and obstacle avoidance sensors.
5.0 Transmitter Details
The remote control allows for precise command over your drone. It comes in two versions: a universal brush remote and a 4.5-inch screen control remote.

Image: Diagram illustrating the functions of the Universal Brush Remote Control.

Image: Diagram illustrating the functions of the 4.5-inch Screen Control Remote.
Important Note:
- The photo and video functions require a TF card to be inserted for use and storage (TF card sold separately).
- If you are using the mobile app link, you must turn off the screen on the remote; the two cannot be used at the same time.
6.0 Installation
6.1 Drone Battery Installation and Removal
Proper installation and removal of the drone battery are crucial for safe operation.

Image: Diagrams illustrating the correct method for installing and removing the drone battery.
- Installation: Push the battery correctly into the drone battery compartment. Ensure you hear a click sound, indicating the battery is firmly installed.
- Removal: Press the lock button on the battery and pull it back to remove it from the fuselage.
Attention: The battery should be installed firmly. Failure to do so may affect the flight safety of your drone, potentially causing a crash due to a power-cut during flight.
6.2 Propeller Installation
Ensure propellers are installed correctly for stable flight.

Image: Diagram showing how to install propellers on the drone, matching 'A' and 'B' labels.
- An "A" or "B" is printed on each propeller.
- Lock the propellers to the corresponding arms of the drone (motor shafts are also marked) with screws.
- Rotate each screw clockwise to secure.
7.0 Charging
Proper charging ensures optimal battery life and flight performance.

Image: Diagram illustrating the connection points for charging the drone battery and the remote control via USB.
7.1 Transmitter Charging
- Connect the transmitter charging port with the USB charging cable.
- Plug the USB charging cable into a USB charging port on a power bank or USB adapter (5V/1A).
- When charging, the indicator light on the transmitter will be red. It will turn off when fully charged.
- The charging time is approximately 90 minutes.
7.2 Drone Battery Charging
- Connect the drone battery with the USB charging cable.
- Plug the USB charging cable into a USB charging port on a power bank or USB adapter (5V/1A).
- When charging, the indicator light will be red. It will turn off when fully charged.
- The charging time is approximately 120 minutes.
8.0 Operation Guide
All operations in this manual use MODE 2 (Left hand throttle is the default setting).
8.1 Pairing
Follow these steps to pair your drone with the remote control:
- Long press the Power Switch to turn on the drone. The indicator light of the drone will keep flashing.
- Place the drone on a flat and level surface with its head facing forward and tail towards the pilot.
- Turn on the transmitter. You will hear a "Di" sound. If pairing is successful, the indicator lights on both the drone and the transmitter will turn constant.

Image: Illustration of turning on the drone for pairing.

Image: Illustration of turning on the remote control for pairing.
8.2 Calibrate the Gyro
Calibrating the gyro ensures stable flight.

Image: Diagram showing both joysticks pushed to the inside, lower corners for gyro calibration.
Push the left and right joysticks simultaneously to the inside, lower corners to calibrate the gyro. The drone indicator will blink and turn solid, and the transmitter will beep once, indicating calibration is complete.
To ensure a stable flight, we suggest calibrating the gyro every time after pairing the drone and after a crash.
8.3 Takeoff/Landing
Effortlessly take off and land your drone with a single button.

Image: Remote control with the one-key takeoff/landing button indicated.
- Takeoff: Short press the Takeoff/Landing button. The drone will automatically take off and hover at 5 ft. You can then control it using the joysticks.
- Landing: During flight, short press the Takeoff/Landing button. The drone will automatically land on the ground.
9.0 Functions Details
9.1 Trimmer
Adjust the drone's flight stability using the trim function.

Image: Remote control diagram highlighting the trim buttons for forward/backward and left/right adjustments.
- F/B Sideward Fly Trim: If the drone drifts forward, press and hold the trim button, then push the right stick down. If it drifts backward, push the right stick up.
- L/R Sideward Fly Trim: If the drone drifts left, press and hold the trim button, then push the right stick right. If it drifts right, push the right stick left.
9.2 Speed Switch
Adjust the drone's speed according to your flying skill and environment.

Image: Remote control diagram highlighting the scroll wheel for speed adjustment.
This drone has three speed settings: low, medium, and high. Adjust the speed using the scroll wheel in the upper-right corner of the remote control. The remote will beep once for low speed, twice for medium speed, and three times for high speed.
9.3 360° Flip
Perform exciting aerial stunts with the 360° flip function.

Image: Remote control diagram highlighting the 360° flip button.
After familiarizing yourself with the drone's functions, you can try this amazing flip mode. When the drone is at least 10 ft from the ground, press down on the (360°) button, then push the right joystick in any direction. The drone will perform a flip toward that direction.
Note: 360° Flip functions better when the battery is fully charged.
9.4 Obstacle Avoidance Function
The drone is equipped with intelligent obstacle avoidance for safer flights.

Image: The M107 Drone using its four-way sensing system to detect and avoid obstacles.
During flight, short press the obstacle avoidance button. When the drone encounters an obstacle, it will automatically rebound in the opposite direction.
Caution: This obstacle-avoidance system uses infrared sensors, which may not perform as well in bright light. Please exercise caution when using it.
9.5 Camera Angle Adjustment
Adjust the camera angle to capture the perfect shot.

Image: Remote control diagram highlighting the scroll wheel for camera angle adjustment.
You can adjust the camera angle using the scroll wheel in the upper-right corner of the remote control. Scrolling left tilts the camera downward, and scrolling right tilts it upward. (The tilt range is -90° to 0°).
9.6 Headless Mode
Headless Mode simplifies control, especially for beginners or when the drone is far away.

Image: Diagram illustrating the drone's orientation relative to the pilot for headless mode.
- Activating: Press and hold the Headless Mode button to activate. The indicator light on the aircraft will flash, and the remote control will emit a "beep-beep-beep~ beep-beep-beep" sound.
- Deactivating: Press the Headless Mode button briefly again. The remote control will beep twice, indicating that the drone has exited headless mode.
Headless Mode is a great training tool for beginner pilots. It is also useful when the drone is too far from the pilot (which makes it difficult to tell its orientation). It keeps the drone traveling forward, backward, left, or right when you move the right joystick in those directions, regardless of which way the front of the head of the drone points to.
10.0 Specifications
Detailed technical specifications for the LYZRC M107 Drone.
| Category | Specification |
|---|---|
| Drone | |
| Weight | 120g (Product Prop PC) / 175g (Desc HTML) / 230g/8.11 oz (PDF) |
| Max Takeoff Weight | <1kg |
| Motor Type | Brushless Motor (1503) |
| Obstacle Avoidance Types | Visual Avoidance (Four-way sensing system) |
| Integrated Propeller Guard | Include |
| Max Wind Speed Resistance | < 10 KM/H |
| Category | Camera Drone |
| Aerial Photography | Yes |
| Folded Dimensions | 14 x 8.7 x 6.8 cm (PDF) / 16 x 10.2 x 11.6 cm (Desc HTML) |
| Unfolded Dimensions | 27 x 24 x 6.8 cm (PDF) / 27.5 x 30.8 x 11.6 cm (Desc HTML) |
| Operating Temperature Range | 0° to 40°C (32° to 104°F) |
| Camera | |
| Camera Integration | Camera Included |
| Camera Mount Type | Fixed Camera Mount |
| Camera Features | 4K HD Video Recording |
| Video Maximum Resolution | 4K (4096*2160) (Actual Pixel 480P) |
| Lens Angle | Electrically Adjustable 90° |
| Sensor Size | 1/2.3 inches |
| Flight Performance | |
| Flight Time | 14min (Product Prop PC) / 15 minutes (PDF) / About 20 Minutes (Desc HTML) |
| Flight Altitude | 200 meters |
| Flight System | Obstacle avoidance + optical flow + brushless |
| Remote Control & Connectivity | |
| Remote Distance | 100m (Product Prop PC) / 80-100 Meters (Desc HTML) / 262 ft/80m (PDF) |
| Connectivity | WiFi |
| Aircraft Operating Frequency | 2.4 GHz (2452-2474MHz) |
| Image Transmission Distance | 3000 meters (PDF) / 60 meters (Desc HTML) |
| Image Transmission Signal | 2.4G HD image transmission / WiFi Transmission |
| Display Control | Yes (4.5-inch screen control remote) |
| GPS | No |
| Battery (Drone) | |
| Capacity | 2500mAh (PDF) / 1000mAh (Desc HTML) / 1800mAh (Desc HTML image) |
| Voltage | 3.7 V |
| Battery Type | Lithium-ion Polymer Battery |
| Charging Temperature Range | 5° to 40°C (41° to 104°F) |
| Charging Time | 120 minutes (Depends on charging power and remaining battery power) |
| Battery (Transmitter) | |
| Battery Type | 3.7v 600mAh (PDF) / Built-in 500mAh Battery (Desc HTML) |
Note: Some specifications may vary slightly between different product descriptions. Please refer to the actual product for precise details.
11.0 Troubleshooting
If you encounter issues with your M107 Drone, refer to the following common problems and solutions:
- Drone does not power on:
- Ensure the drone battery is fully charged and correctly installed.
- Check the power switch on the drone.
- Remote control does not power on:
- Ensure the remote control battery is charged.
- Check the power switch on the remote control.
- Drone and remote control fail to pair:
- Ensure both devices are powered on and within range.
- Repeat the pairing process as described in section 8.1.
- Drone drifts during flight or is unstable:
- Calibrate the gyro as described in section 8.2.
- Use the trimmer function (section 9.1) to adjust for minor drifts.
- Check propellers for damage or incorrect installation.
- Camera not recording or taking photos:
- Ensure a TF card is inserted into the drone (sold separately).
- If using the mobile app, ensure the remote control screen is off.
- Obstacle avoidance not working effectively:
- The infrared sensors may be less effective in bright light conditions. Exercise caution.
- Ensure the obstacle avoidance mode is activated (section 9.4).
- Short flight time:
- Ensure the battery is fully charged before flight.
- Flight time can be affected by wind speed, temperature, and aggressive flying.
- Consider purchasing additional batteries for extended flight sessions.
12.0 User Tips
Enhance your drone flying experience with these helpful tips:
- No Registration Required: The drone's weight is below the 250g threshold for registration in most countries, allowing for recreational use without tedious paperwork.
- TF Card for Media: Remember to insert a TF card (not included) into the drone to save your photos and videos. Without it, you won't be able to record.
- Understand Camera Resolution: While the drone supports 4K video format, the actual shooting pixel is 480P. This is suitable for daily entertainment and casual recording.
- Practice in Headless Mode: If you're a beginner, start with Headless Mode (section 9.6) to get accustomed to controls without worrying about the drone's orientation.
- Pre-Flight Check: Always perform a thorough check of the drone and remote before each flight, including battery levels, propeller integrity, and environmental conditions.
- Consider Extra Batteries: For longer flying sessions, it's highly recommended to have spare batteries fully charged.
13.0 Warranty and Support
We are committed to providing high-quality products and thoughtful after-sales service.
- Product Manual (PDF): For a detailed digital copy of the user manual, please refer to the User Manual (PDF).
- Contact Support: If you have any questions about the product (such as operation, maintenance, or after-sales support), please feel free to contact the seller. They aim to reply within 24 hours.
- Age Recommendation: This product is suitable for users over 14 years old. Children should use it under the supervision of adults to avoid safety accidents.
14.0 General Information
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RF Exposure
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body. This part belongs to the drone.
RF warning for Portable device: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. This part belongs to the transmitter.
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
CAN NMB-003 (B)
Radiation Exposure Statement
The device is in compliance with RF exposure guidelines. Users can obtain Canadian information on RF exposure and compliance. The minimum distance from the body to use the device is 20cm.

MADE IN CHINA(CN)
