Important Reminders and Safety Warnings
WARNING: Not suitable for children under 36 months.
General Safety Precautions
- Do not fly towards other people's heads.
- Rotating motors may tangle with hair.
- When inspecting and maintaining the aircraft, always disconnect the battery first.
- Do not reach into the protective casing when the motor is spinning at high speed.
- Sharp objects entering the protective casing may damage the high-speed propeller.
- Do not operate the drone in hot, cold, strong wind, or heavy rain conditions.
- Ensure the drone is operated in an open area, away from people, pets, power lines, and other obstacles.
- Do not let the aircraft fly out of sight.
- After the aircraft starts, keep hands away from high-speed rotating parts and propellers to avoid injury.
- The battery and motor may become hot during and after use; avoid touching them immediately to prevent burns.
- Do not look directly at the LED light beam to avoid eye damage.
Battery Usage Precautions
- Use only the original manufacturer's dedicated charger (USB). Do not use damaged or other brand chargers.
- Do not charge swollen, leaking, or damaged batteries.
- Do not overcharge the battery. Unplug the charger once the battery is fully charged.
- Do not charge on surfaces near flammable materials (carpets, wooden floors, solid wood furniture, etc.) or conductive objects.
- Allow the battery to cool down for 10-15 minutes after use before charging.
- The ideal charging temperature for the battery is between 0°C and 40°C.
- Excessive discharge can cause the battery to heat up and swell.
- Long-term or high-current charging can also cause the battery to swell and damage it.
- Leaving the battery fully charged or discharged for a long time can easily damage it.
- Battery usage over a long period of time can result in decreased battery life.
- Someone should be present when charging the battery; charging should be paused if unattended.
- Properly store and dispose of the battery.
- Do not place charged batteries in high-temperature areas, near open flames or heating devices, as this may cause damage or explosion.
- Do not strike or hit the battery against hard surfaces.
- Do not immerse the battery in water.
- Store batteries in a dry place.
- Do not disassemble the battery.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.
Product Overview
The YL16 Racing Football Drone is a compact and durable quadcopter designed for both indoor and outdoor use. It features a unique spherical protective cage for 360-degree all-round protection, making it resistant to collisions and falls. The drone is equipped with LED lights for enhanced visibility and an air pressure system for stable hovering.
Product Specifications
| Attribute | Value |
|---|---|
| Product Name | Football drone |
| Product Model | YL16 |
| Product Color | Red / Blue |
| Product Weight (Drone) | 50g |
| Product Weight (with packaging) | 298g |
| Product Size | 15*15*12CM |
| Material | Plastic, Metal, Electronic Components |
| Receiving Frequency | 2.4G |
| Operation Method | Remote control |
| Drone Battery Capacity | 3.7V 500mAh (Lithium battery) |
| Controller Battery | 3.7V 950mAh (Internal), AAA*3 (External, not included) |
| Remote Control Range | 60M |
| Flight Time | 5~10 minutes (approx. 6-8 minutes) |
| Charging Time | About one hour |
| Speed Adjustment | Low, Medium, High |
| Control Channels | 4 channels |
| Controller Mode | MODE2 |
| Operator Skill Level | Intermediate, Expert, Beginner |
| Indoor/Outdoor Use | Indoor-Outdoor |
| Anti-wind Ability | 4 |
| Aerial Photography | No |
| Certification | CE |
Package Contents
Please check the package contents upon receipt:
- 1 x YL16 Racing Football Drone
- 1 x Remote Controller
- 1 x Drone Battery (3.7V 500mAh)
- 1 x USB Charging Cable
- 1 x Screwdriver
- 4 x Backup Fan Blades
- 1 x Instruction Manual

Setup
Battery Installation (Drone)
The YL16 drone uses a modular battery for easy installation and replacement. Ensure the drone is powered off before installing or removing the battery.


Remote Control Battery Installation
The remote controller requires 3 AAA batteries (not included). Install them according to the polarity markings inside the battery compartment. Do not mix old and new batteries or different types of batteries. Non-rechargeable batteries cannot be charged.
Charging the Drone Battery
Before first use, fully charge the lithium battery. Connect the USB charging cable to the drone battery and a compatible 5V1-2A USB adapter. The LED indicator on the charger will show the charging status. Do not leave the battery unattended while charging. Once fully charged, disconnect the charger.
Operating Instructions
Remote Control Layout

| NO. | Name | Function |
|---|---|---|
| 01 | Power Button | Power on/off |
| 02 | Speed Adjustment Key | Three-speed switch: low/medium/high |
| 03 | Roll Key | Perform rolling actions with the joystick |
| 04 | Left Joystick | Control ascent and descent as well as the nose's left and right turns |
| 05 | Right Joystick | Control forward and backward movement and left and right translation |
| 06 | Headless Mode/Switch to Japanese Hand | Short Press to Enter Headless Mode/Press and hold the button to turn on the remote control power and switch to Japanese Hand |
| 07 | One Click Return | Switch front light mode |
| 08 | One Click Takeoff/Landing | Unlock motors/emergency stop motors/Long press to cancel height hold |
| 09 | Light Button | Switch light colors |
| 10 | Rear Fine Tuning | Rear Fine Tuning |
| 11 | Front Fine Tuning | Front Fine Tuning |
| 12 | Right fine-tuning | Right fine-tuning |
| 13 | Left fine-tuning | Left fine-tuning |
Pairing the Drone and Remote Control
To ensure stable connection, make sure all other nearby aircraft are turned off during the pairing process. If using multiple drones, pair them one by one.
- Connect the aircraft power. The LED lights on the drone will flash.
- Turn on the power of the remote control.
- The LED lights on the aircraft will stop flashing, indicating successful pairing.
IMU Calibration
It is recommended to calibrate the aircraft before each takeoff to ensure stable flight.
- Place the aircraft on a level surface (ground or table).
- Move both the left and right joysticks of the remote control to the bottom-right position simultaneously, as shown in the diagram. The LED lights will start to flash.
- When the LED lights stop flashing, the calibration is successful.

Takeoff and Landing
The YL16 drone supports one-click takeoff and landing, as well as handheld takeoff.
- One-Click Takeoff: Press the 'One Click Takeoff/Landing' button (NO. 08) on the remote control. The drone will automatically ascend and hover at a stable altitude.
- Handheld Takeoff: Hold the drone gently in your hand and launch it upwards. The drone will automatically stabilize and fly.
- One-Click Landing: Press the 'One Click Takeoff/Landing' button (NO. 08) again. The drone will slowly descend and land.


Stable Hovering
Equipped with a high-precision air pressure system, the drone will automatically stabilize and stop in the air, ensuring safety. Even in the presence of air turbulence, beginners can focus on practicing control of the flight direction.

Headless Mode
In Headless Mode, the drone's orientation is irrelevant to the control inputs. The forward direction will always be the direction the drone was facing when Headless Mode was activated, regardless of how the drone rotates during flight.
- Activating Headless Mode: Short press the 'Headless Mode/Switch to Japanese Hand' button (NO. 06).
- Deactivating Headless Mode: Short press the button again.

360-Degree Rolling and Stunts
The spherical drone is capable of performing 360-degree special stunts with rolls. This feature allows for visually stunning aerial performance.
- Performing a Roll: Press the 'Roll Key' button (NO. 03) and simultaneously move the right joystick in the desired direction (left, right, forward, or backward) to perform a rolling action.


Speed Adjustment
The drone offers multiple flight speeds (low, medium, high) to suit different skill levels and environments.
- Adjusting Speed: Press the 'Speed Adjustment Key' button (NO. 02) to cycle through the low, medium, and high-speed settings.

Anti-Turtle Function
If the drone falls to the ground, collides with obstacles, or lands upside down, the anti-turtle function can automatically flip the drone back to its correct orientation, allowing for immediate remote takeoff without manual adjustment.
- Activating Anti-Turtle: When the drone is upside down, push the left joystick of the remote control upwards to trigger this function.

Multiplayer Battles and Throwing Mode
The 2.4G remote control allows for multiplayer battles without interference. The drone also features a throwing mode for easy launch.

Video Demonstration
Maintenance
Motor Care
It is recommended to replace the motor after approximately 30 battery cycles. For optimal motor maintenance, allow the motors to cool down for two minutes after flying with two batteries before continuing to fly. After each flight, check the motor temperature. If a motor's temperature is excessively high, it should be replaced promptly to prevent excessive current from damaging the mainboard.
Propeller Replacement
If the propellers are damaged, they can be replaced using the included screwdriver and backup fan blades. Carefully remove the screw holding the damaged propeller and install a new one, ensuring it is securely fastened.
Troubleshooting
- Drone not performing rolls or maintaining height: Check the battery level. Low battery can affect the drone's power for stunts and altitude hold.
- Drone is upside down after a fall or collision: Activate the Anti-Turtle Function by pushing the left joystick upwards.
- Drone not responding to remote control: Ensure the drone and remote control are properly paired. Re-pair if necessary. Check remote control batteries.
- Drone unstable or drifting: Perform IMU calibration on a flat surface.
- Motors not spinning: Check for tangled hair or debris in the motors. Ensure the battery is connected and charged.
User Tips
- It is highly recommended that beginners practice flying at low altitudes for about 3 days to become familiar with the controls before attempting high-altitude flights.
- Always ensure the drone battery is fully charged before each flight for optimal performance and flight time.
Warranty and Support
This product is a precision device integrating mechanical, electronic, aerodynamic, and high-frequency emission technologies. Proper assembly and debugging are required to avoid accidents. The product owner must operate it safely to prevent personal injury or property damage.
If you encounter any issues with use, operation, or maintenance, please contact your local dealer or the company's customer support for assistance.