EPever VS-AU Series Solar Charge Controller

Contents

EPEVER VS-AU Series PWM Solar Charge Controller User Manual

Model: VS-AU Series

Brand: EPever

1. Overview

Thank you for selecting the ViewStar AU series common positive solar charge controller. The VS-AU controller is a PWM charge controller with built-in LCD display that adopts the most advanced digital technique. The multiple load control modes enable it can be widely used on solar home system, traffic signal, solar street light, solar garden lamp, etc.

The VS-AU series is designed for solar energy systems where the gap between solar panel working voltage and battery voltage is not significant, offering a reliable and cost-effective solution. It is widely applied in rural electrification and home power systems.

EPEVER VS-AU Solar Charge Controller
Figure 1: EPEVER VS-AU Series PWM Solar Charge Controller with Dual USB Ports.

2. Product Features

  • Adopt high quality components of ST, IR and Infineon, ensuring product lifespan.
  • Terminals have UL and VDE certification, enhancing product safety and reliability.
  • Controller can work continuously at full load within the environment temperature range from -25°C to 55°C.
  • 3-Stage intelligent PWM charging: Bulk, Boost/Equalize, Float.
  • Support 3 charging options: Sealed, Gel, and Flooded batteries.
  • LCD display design, dynamically displaying device's operating data and working condition.
  • Double USB design, providing power supply charge for electronic equipment (5VDC/2.4A total output).
  • Humanized button settings for comfortable and convenient operation.
  • Multiple load control modes.
  • Energy statistics function.
  • Battery temperature compensation function.
  • Extensive Electronic protection.
Dual USB Ports and Segmented LCD Display
Figure 2: Controller featuring Double USB Port Design and Segmented LCD Display.
Battery Temperature Compensation and Load Mode Setting
Figure 3: Battery Temperature Compensation Function and Load Mode Settings (Light ON/OFF, Manual, Test).
Real-Time Energy Statistics and Battery Type Support
Figure 4: Real-Time Energy Statistics Function and support for Sealed, Gel, and Flooded battery types.

3. Wiring

Connect components to the charge controller in the sequence as shown in the diagram below and pay much attention to the "+" and "-" polarities. Please do not insert the fuse or turn on the breaker during the installation. When disconnecting the system, the order should be reversed.

After powering on the controller, check the LCD. If it does not display, refer to chapter 6 (Troubleshooting). Always connect the battery first, in order to allow the controller to recognize the system voltage.

The battery fuse should be installed as close to the battery as possible. The suggested distance is within 150mm.

The VS-AU series is a positive ground controller. Any positive connection of solar, load or battery can be earth grounded as required.

NOTE: Please connect the inverter or other load that has a large start current to the battery rather than to the controller, if the inverter or other load is necessary.

Wiring Diagram for Solar Charge Controller
Figure 5: Connection Diagram. (1) Battery, (2) Load, (3) PV Array.

Optional Accessory: Remote Temperature Sensor (RTS)

Name: Remote Temperature Sensor
Model: RTS300R47K3.81A

Acquisition of battery temperature for undertaking temperature compensation of control parameters. The standard length of the cable is 3m (length can be customized). The RTS300R47K3.81A connects to port ③ on the controller.

NOTE: Unplug the RTS, the temperature of battery will be set to a fixed value 25°C.

4. Operation

4.1 Button Function

ButtonFunction
MENU buttonBrowse interface
Setting parameter
SET buttonLoad ON/OFF
Clear error
Enter into Set Mode
Save data

4.2 LCD Display

LCD Display Icons and Meanings
Figure 6: LCD Display Icons and their corresponding meanings.

Status Description

ItemIconStatus
Day
Night
PV arrayNo charging
Charging
PVPV Voltage, Current, Power
Battery capacity, in Charging
BatteryBATT.Battery voltage, current, temperature
BATT. TYPEBattery type
LoadLoad ON
Load OFF
LOADLoad Voltage, Current, Load mode

Browse Interface

When there is no operation, the interface will automatically cycle through different displays. The following two interfaces will not be displayed during automatic cycle:

  • Load Type: Displays the current load mode.
  • Accumulative Power: Displays total energy generated.

Accumulative power zero clearing: Under PV power interface, press SET button and hold for 5s then the value will blink. Press SET button again to clear the value.

Setting temperature unit: Under battery temperature interface, press SET button and hold for 5s to switch between °C and °F.

4.3 Load Mode Setting

Operating Steps: Under load mode setting interface, press SET button and hold for 5s until the number begins flashing. Then press MENU button to set the parameter, press SET button again to confirm.

ModeTimer 1ModeTimer 2
Light ON/OFFDisabled
Load will be on for 1 hour since sunsetLoad will be on for 1 hour before sunrise
Load will be on for 2 hours since sunsetLoad will be on for 2 hours before sunrise
Load will be on for 3-13 hours since sunsetLoad will be on for 3-13 hours before sunrise
Load will be on for 14 hours since sunsetLoad will be on for 14 hours before sunrise
Load will be on for 15 hours since sunsetLoad will be on for 15 hours before sunrise
Test modeDisabled
Manual mode (Default load ON)Disabled

NOTE: Please set Light ON/OFF, Test mode and Manual mode via Timer1. Timer2 will be disabled and display "2 n".

4.4 Battery Type

Operating Steps: Under Battery Voltage interface, press SET button and hold for 5s then enter into the interface of Battery type setting. After choosing the battery type by pressing MENU button, waiting for 5s or pressing SET button again to modify successfully.

Battery Type Selection
Figure 7: Battery Type Selection (Sealed, Gel, Flooded).

NOTE: Please refer to the battery voltage parameters table for the different battery types in the Specifications section.

Maintenance

The EPEVER VS-AU series solar charge controller is designed for durability and requires minimal maintenance. However, to ensure optimal performance and longevity, consider the following:

  • Regular Inspection: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Cleanliness: Keep the controller clean and free from dust and debris. Use a dry, soft cloth for cleaning. Do not use liquids or solvents.
  • Ventilation: Ensure that the controller's ventilation openings are not obstructed to allow for proper heat dissipation.
  • Environmental Conditions: Operate the controller within its specified temperature and humidity ranges. Avoid exposure to direct sunlight, rain, or excessive moisture.

6. Troubleshooting

FaultsPossible reasonsTroubleshooting
The LCD is off during daytime when sunshine falls on PV modules properlyPV array disconnectionConfirm that PV wire connections are correct and tight.
Wire connection is correct, LCD not display1) Battery voltage is lower than 9V
2) PV voltage is less than battery voltage
1) Please check the voltage of battery. At least 9V voltage to activate the controller.
2) Check the PV input voltage which should be higher than battery's.
Interface blink: Battery over voltageBattery over voltageCheck if the battery voltage is higher than OVD point (over voltage disconnect voltage), and disconnect the PV.
Interface blink: Battery over dischargedBattery over dischargedWhen the battery voltage is restored to or above LVR point (low voltage reconnect voltage), the load will recover.
Interface blink: Battery OverheatingBattery OverheatingThe controller will automatically turn the system off. But while the temperature decline to be below 50°C, the controller will resume.
Interface blink: Over load or Short circuitOver load or Short circuitPlease reduce the number of electric equipment or check carefully loads connection.

5. Protections

ProtectionConditionsStatus
PV Reverse PolarityWhen the battery is correct connecting, the PV can be reversed.The controller is not damaged
Battery Reverse PolarityWhen the PV is not connecting, the battery can be reversed.
Battery Over VoltageThe battery voltage reaches to the OVDStop charging
Battery Over DischargeThe battery voltage reaches to the LVDStop discharging
Battery OverheatingTemperature sensor is higher than 65°C
Temperature sensor is less than 55°C
Output is OFF
Output is ON
Load failureLoad overload / Load short circuitWhen load current reaches 1.02-1.05 times, 1.05-1.25 times, 1.25-1.35 times and 1.35-1.5 times more than nominal value, controller will automatically turn off loads in 50s, 30s, 10s and 2s respectively.

7. Technical Specifications

ItemVS1024AUVS2024AUVS3024AUVS4524AUVS6024AU
Nominal system voltage12/24VDC Auto
Battery input voltage range9V ~ 32V
Rated charge current10A@55°C20A@55°C30A@55°C45A@55°C60A@55°C
Rated discharge current10A20A30A45A60A
Max. PV open circuit voltage50V
Battery typeSealed (Default) / Gel / Flooded
Equalize Charging VoltageSealed:14.6V / Gel: No / Flooded:14.8V
Boost Charging VoltageSealed:14.4V / Gel:14.2V / Flooded:14.6V
Float Charging VoltageSealed/Gel/Flooded:13.8V
Low Voltage Reconnect VoltageSealed/Gel/Flooded:12.6V
Low Voltage Disconnect VoltageSealed/Gel/Flooded:11.1V
Self-consumption≤9.2mA/12V; ≤11.7mA/24V
USB output5VDC/2.4A (Total)
Temperature compensation coefficient-3mV/°C/2V (25°C)
Charge circuit voltage drop≤0.29V
Discharge circuit voltage drop≤0.16V
LCD temperature range-20°C ~ +70°C
Working environment temperature-25°C ~ +55°C (Product can work continuously at full load)
Relative humidity≤95%, N.C.
EnclosureIP30
GroundingCommon Positive
Overall dimension (LxWxH)(mm)142x85x41.5160x94.9x49.3181x100.9x59.8194x118.4x63.8214x128.7x72.2
Mounting dimension130x60mm148x70mm172x80mm185x90mm205x100mm
Mounting hole sizeΦ4.5mm
Terminals4mm²/12AWG10mm²/8AWG16mm²/6AWG16mm²/6AWG25mm²/4AWG
Net weight0.22kg0.35kg0.55kg0.76kg1.02kg

Note: Above parameters are in 12V system at 25°C, twice in 24V system, triple in 36V system and quadruple in 48V system.

Specifications Table for VS3048AU, VS4548AU, VS6048AU
Figure 8: Specifications for higher voltage models (VS3048AU, VS4548AU, VS6048AU).

User Tips

No specific user tips were available from buyer reviews or Q&A content for this product. Always refer to the manual for detailed instructions and safety guidelines.

Warranty & Support

8. Disclaimer

This warranty does not apply under the following conditions:

  1. Damage from improper use or use in an unsuitable environment.
  2. PV or load current, voltage or power exceeding the rated value of controller.
  3. The controller's working temperature exceeds the limit working environment temperature.
  4. User disassembly or attempted repair of the controller without permission.
  5. The controller is damaged due to natural elements such as lightning.
  6. The controller is damaged during transportation and shipment.

Certifications

The EPEVER VS-AU series solar charge controller is certified with:

  • CE
  • FCC
  • RoHS
  • IEC
  • EMC
  • UL (where applicable)
Product Certifications
Figure 9: Various certifications and qualifications for EPEVER products.

© 2024 EPever. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.