1. Introduction
This manual provides instructions for the installation and maintenance of replacement accessories for your Dreame L10s Ultra Gen2 or L10s Pro Ultra Heat robotic vacuum cleaner. Regular replacement and maintenance of these parts ensure your vacuum operates at peak efficiency, providing a clean and healthy home environment.

Figure 1: Complete set of replacement accessories.
2. Safety & Warnings
WARNING:
- TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN.
- DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAY PENS.
- THIS BAG IS NOT A TOY.
3. Setup and Installation
Always ensure the robot vacuum is powered off before attempting to replace any parts.
3.1 Main Brush Installation
- Flip the robot upside down to access the main brush compartment.
- Open the main brush compartment cover.
- Align the new main brush with the slots.
- Push the main brush firmly into place until it clicks.
- Close the compartment cover securely.

Figure 2: Main Roller Brush.
3.2 Side Brush Installation
- Flip the robot upside down.
- Locate the side brush mounting hole.
- Align the new side brush with its mounting hole.
- Tighten the screw clockwise until the side brush is firmly secured.

Figure 3: Side Brush.
3.3 Dust Bag Replacement
- Remove the dust box from the robot.
- Carefully take out the old, full dust bag.
- Insert a new dust bag into the dust box.
- Ensure the new dust bag is seated firmly.
- Insert the dust box back into the robot.

Figure 4: Dust Bag.
3.4 Mop Pad Attachment
- If using for wet cleaning, wring out the mop pad to remove excess water.
- Align the mop pad with the bottom mounting plate of the robot.
- Press the mop pad firmly onto the Velcro strips on the mounting plate to secure it.

Figure 5: Mop Pad.
3.5 Filter Replacement/Cleaning
- Remove the dust box from the robot.
- Take out the old filter from the dust box.
- Replace with a new filter, or clean the existing filter by tapping out debris (do not wash HEPA filters with water unless specified).
- Insert the filter back into the dust box.
- Insert the dust box back into the robot.

Figure 6: HEPA Filter.
4. Operating
These accessories are designed to restore and maintain the optimal cleaning performance of your Dreame L10s Ultra Gen2 / L10s Pro Ultra Heat vacuum cleaner. Once installed, the robot will utilize these parts as part of its normal cleaning cycles.
5. Maintenance
- Main Brush & Side Brushes: Regularly check for tangled hair or debris and remove them to prevent damage and maintain cleaning effectiveness.
- HEPA Filter: Clean the filter periodically by gently tapping it to remove dust. Replace every 3-6 months depending on usage. Do not wash with water unless explicitly stated for your filter type.
- Mop Pads: Wash mop pads after each use, especially after wet cleaning, to ensure hygiene and effective mopping.
- Dust Bag: Replace the dust bag when it is full to maintain suction power and prevent dust leakage.
6. Troubleshooting
If you notice a decrease in your vacuum cleaner's performance (e.g., reduced suction, poor cleaning, unusual noises), consider the following:
- Reduced Suction: Check if the dust bag is full or if the filter is clogged. Replace the dust bag or clean/replace the filter.
- Poor Cleaning Performance: Inspect main and side brushes for wear or entanglement. Clean or replace as necessary. Ensure mop pads are clean and properly attached.
- Unusual Noises: Check brushes for any foreign objects or damage.
7. Specifications
| Attribute | Detail |
|---|---|
| Material | Plastic |
| Vacuum Part Type | BRUSHES |
| Model Number | For Dreame L10s Ultra Gen2 / L10s Pro Ultra Heat |
| Type | Vacuum Cleaner Parts |
| Origin | Mainland China |
8. User Tips
- Regular Replacement: For optimal cleaning performance and to extend the lifespan of your robot vacuum, replace consumable parts like filters, brushes, and mop pads according to the manufacturer's recommendations or when visible wear occurs.
- Compatibility Check: Always verify that the replacement parts are compatible with your specific Dreame model (L10s Ultra Gen2 or L10s Pro Ultra Heat) to ensure a perfect fit and function.
- Value for Money: Users have found these accessories to be a suitable and affordable option for maintaining their Dreame vacuum cleaners.
9. Warranty and Support
For any questions or issues regarding these replacement accessories:
- If you have any questions during use, please leave a message through the seller's platform.
- If you need to contact the seller, please do so through the AliExpress backend messaging system.
- For additional information or the original device manual, you may refer to the official user manual PDF: View User Manual (PDF).