ATA PTX-4

Contents

ATA PTX-4 Securacode Garage Door Remote Control User Manual

1. Product Overview

The ATA PTX-4 Securacode Remote Control is designed for operating ATA garage door and gate openers. This 4-button remote utilizes a 433.92MHz frequency and rolling code technology for enhanced security. It is specifically compatible with ATA Securacode systems.

ATA PTX-4 Remote Control in multiple colors

Figure 1: ATA PTX-4 Remote Control (various styles)

Compatibility with ATA PTX4 Securacode

Figure 2: The remote is 100% compatible with ATA PTX4 Securacode systems.

2. Specifications

FeatureDetail
Model NumberATA PTX-4
Encoding MethodRolling code
Frequency433MHz / 433.92MHz
Number of Buttons4
OriginMainland China
Compatibility NoteNot compatible with other brands
Package Length11 cm
Package Width11 cm
Package Height2 cm
Package Weight0.032 kg

The remote is designed to work with various ATA PTX4 compatible systems, including:

  • CRX-1, CRX-2
  • GDO-2v5, GDO-2v6, GDO-2v7
  • GDO-4v3, GDO-4v4, GDO-4v5, GDO-4v6
  • GDO-6v1, GDO-6v2
  • GDO-7v1, GDO-8v1, GDO-8v2, GDO-9v1
ATA PTX4 compatible models list

Figure 3: List of compatible ATA PTX4 garage door and gate opener models.

3. Setup: Storing Transmitter Code

Before programming, ensure the battery (typically 23A, visible in the remote's transparent casing) is correctly installed in the transmitter.

  1. Access Opener/Receiver: Press and hold the blue Door Code button on your opener unit or the SW1 or SW2 button on the receiver board.
  2. Initiate Pairing: Press the transmitter button you wish to use to control your door/gate for two seconds.
  3. Confirm Pairing (First Pulse): Release the transmitter button and pause for two seconds.
  4. Confirm Pairing (Second Pulse): Press the same transmitter button again for two seconds.
  5. Exit Programming: Release the Door Code button or SW button on your opener/receiver.
  6. Test Operation: Press the programmed transmitter button to test the operation of your door or gate.

Removing a Transmitter's Code

To remove a transmitter's code from the device, repeat the steps 1-5 above. This will typically overwrite or clear the stored code for that button.

Video 1: Demonstration of remote control function and pairing process with a receiver board.

4. Operating Instructions

Once the remote control has been successfully programmed to your garage door or gate opener, simply press the corresponding button on the remote to activate or deactivate the opener. The LED indicator on the remote will light up when a button is pressed, confirming signal transmission.

5. Maintenance

Battery Replacement

The remote control is powered by a 23A 12V battery. If the LED indicator on the remote becomes dim or fails to light up when a button is pressed, it's time to replace the battery. To replace, carefully open the remote casing (usually by unscrewing a small screw on the back or prying gently along the seam) and replace the old battery with a new 23A 12V battery, ensuring correct polarity.

Cleaning and Storage

  • Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Avoid exposing the remote to direct sunlight, extreme temperatures, high humidity, or water.
  • Store the remote in a safe place where it won't be accidentally pressed or damaged.

6. Troubleshooting

ProblemPossible CauseSolution
Remote does not workLow or dead batteryReplace the 23A 12V battery.
Remote is out of rangeMove closer to the garage door/gate opener.
Remote is not programmedFollow the 'Setup: Storing Transmitter Code' instructions to program the remote.
InterferenceCheck for other devices operating on similar frequencies.
LED on remote does not light upDead or incorrectly installed batteryReplace the battery and ensure correct polarity.

7. User Tips

  • Always ensure the remote is properly paired with your opener for reliable and consistent operation.
  • Keep the remote in a secure location to prevent accidental activation of your garage door or gate.
  • If you have multiple remotes, label them to easily identify which one controls which door/gate.

8. Warranty and Support

This product is manufactured by Shenzhen Scimagic Development Technology Co.Ltd. For any issues or support inquiries, please contact your seller or the manufacturer directly. Specific warranty terms may vary; please refer to your purchase documentation for details.

Manufacturer Address: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.