VGR V-887

Contents

VGR V-887 Hair Clippers and Trimmers Set User Manual

Model: V-887 (V-887C/T)

1. Important Safety Information

Please read all instructions carefully before using the VGR V-887 Hair Clippers and Trimmers Set. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

2. Product Overview

The VGR V-887 is a high-performance hair clipper and trimmer set designed for precise and efficient hair cutting. It features advanced blade technology, adjustable speed settings, and an ergonomic design for professional and home use.

VGR V-887 Hair Clipper and Trimmer Set on charging docks, highlighting 9000 RPM and blade features.

Figure 1: VGR V-887 Hair Clipper and Trimmer Set with key features like 9000 RPM, blue ceramic and DLC coating blades, and rotary infinity speed change.

2.1. Package Contents

Please check the package for the following items:

Hair Clipper

  • 1 x Hair Clipper
  • 1 x Protective Cap
  • 1 x Cleaning Brush
  • 1 x USB Charging Cable
  • 6 x Guide Combs
  • 1 x Right Taper Lever
  • 1 x Charging Base
  • 1 x Instruction Manual

Hair Trimmer

  • 1 x Hair Trimmer
  • 1 x Protective Cap
  • 1 x Cleaning Brush
  • 1 x USB Charging Cable
  • 3 x Guide Combs
  • 1 x Charging Base
  • 1 x Instruction Manual

3. Setup

  1. Unboxing: Carefully remove all components from the packaging.
  2. Protective Films: Before first use, remove any protective films from the device body and blades.
  3. Initial Charge: It is recommended to fully charge the device before its first use. Connect the provided USB charging cable to the charging port on the device or the charging base, and then connect the other end to a certified 5V power adapter (not included).
VGR V-887 Hair Clipper and Trimmer on charging docks, showing charging time, battery, and operating time.

Figure 2: VGR V-887 charging setup. Charging time is approximately 3 hours for a full charge.

4. Operating Instructions

4.1. Power On/Off

  • To Turn On: Press and hold the power button (machine switch) for approximately 3 seconds.
  • To Turn Off: Press and hold the power button for approximately 3 seconds again.

4.2. Adjusting Speed (7000-9000 RPM)

Both the clipper and trimmer feature a sliding roller for speed adjustment:

  • To Adjust Speed: Slide the roller up or down. The rotation speed can be adjusted from a minimum of 7000 RPM to a maximum of 9000 RPM.
  • LED Display Light: The LED display light indicates the current speed. The higher the rotation speed, the bluer and brighter the light will be.
Close-up of VGR V-887 speed adjustment roller, machine switch, and LED display light.

Figure 3: Speed adjustment mechanism and LED indicator on the VGR V-887.

4.3. Hair Clipper Usage

  • Blades: The clipper uses high-quality blue ceramic and MIM blades for sharp, wear-resistant, and smooth cutting.
  • Adjustable Lever: The clipper features an adjustable lever with five settings for precise cutting lengths: 0.8mm, 1.1mm, 1.4mm, 1.7mm, and 2mm. Adjust the lever to your desired length before cutting.
  • Guide Combs: Attach the appropriate guide comb for longer hair lengths.
Close-up of VGR V-887 clipper's adjustable lever with settings from 0.8mm to 2mm.

Figure 4: Adjustable lever on the hair clipper for precise length control.

4.4. Hair Trimmer Usage

  • Blades: The trimmer is equipped with a blue ceramic DLC blade, designed for ultra-sharp, wear-resistant, and precise 0mm cutting.
  • Precision: Ideal for detailing, outlining, and achieving very short hair lengths.
  • Guide Combs: Use the included guide combs for desired trimming lengths.
Close-up of VGR V-887 trimmer's 0mm cutting blade for precision carving.

Figure 5: The trimmer's 0mm cutting blade for millimeter-level precision.

5. Maintenance

5.1. Cleaning

  1. Turn Off: Always ensure the device is turned off and disconnected from power before cleaning.
  2. Brush Away Hair: Use the provided cleaning brush to remove any hair clippings from the blades and the device body.
  3. Wipe Down: Wipe the body of the clipper/trimmer with a soft, dry cloth. Do not use abrasive cleaners or immerse the device in water.

5.2. Lubrication

Due to airline regulations, lubricants are not included with this product. For optimal performance and blade longevity, it is recommended to periodically apply a small amount of clipper oil (not included) to the blades after cleaning. Turn the device on for a few seconds to distribute the oil evenly, then turn it off and wipe off any excess.

5.3. Storage

After use, turn off the device and store it in a dry place, away from direct sunlight and moisture. Keep it out of reach of children.

6. Troubleshooting

If you encounter any issues with your VGR V-887 set, please refer to the following common solutions:

  • Device Not Turning On: Ensure the device is fully charged. If it still doesn't turn on, try connecting it to the charger to see if the charging indicator lights up.
  • Poor Cutting Performance: Clean the blades thoroughly to remove any trapped hair. Ensure the blades are properly lubricated. If the issue persists, the blades may need replacement (contact support).
  • Device Not Charging: Check if the USB cable is securely connected to both the device/base and the power adapter. Ensure the power adapter is working correctly.
  • Excessive Noise/Vibration: Clean and lubricate the blades. Ensure no hair is caught in the motor area.

For issues not resolved by the above steps, please contact customer support.

7. Specifications

FeatureSpecification
ModelV-887 (V-887C/T)
Charging TimeApprox. 3 Hours
Battery TypeLithium Battery
Battery Capacity2500 mAh
Operating TimeUp to 250 Minutes
Motor Speed7000-9000 RPM (Adjustable)
Clipper Blade MaterialBlue Ceramic & MIM Blades
Trimmer Blade MaterialBlue Ceramic DLC Blade
Clipper Length Adjustment0.8mm, 1.1mm, 1.4mm, 1.7mm, 2mm
Minimum Haircut LengthLess than 0.5mm (Trimmer)
Power TypeRechargeable/Electric Both Work
Voltage<20V
FunctionsWet/Dry Haircut, Fast Charging, Charging Indication

8. User Tips

  • For best results, ensure hair is clean and dry before cutting, unless performing a wet haircut.
  • Always start with a longer guide comb if you are unsure of the desired length, and gradually reduce it.
  • Move the clipper/trimmer against the direction of hair growth for a more even cut.
  • Regular cleaning and lubrication of the blades will significantly extend the life and performance of your device.

9. Warranty and Support

9.1. Warranty

All VGR products, including the V-887 Hair Clippers and Trimmers Set, come with a 12-month warranty from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear.

9.2. Manufacturer Information

Manufacturer: Ningbo Woji Electric Appliance Co., Ltd.
Address: CN-CN-No. 656, Kaifa East Road, Zhouxiang Town, Cixi City, Ningbo, Zhejiang

9.3. Customer Support

For warranty claims, technical support, or any inquiries regarding your VGR V-887 set, please contact your retailer or the official VGR customer service channel.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.