1. Introduction
Thank you for choosing QCY Melobuds N50 Wireless Earphones. This manual provides detailed instructions on how to set up, operate, and maintain your new earphones. Please read it carefully before use and keep it for future reference.

QCY Melobuds N50 Wireless Earphones and Charging Case
2. Package Contents
Please check the package for the following items:
- QCY Melobuds N50 Earbuds (Left and Right)
- Charging Case
- Eartips (S, M, L sizes - M size pre-installed)
- Type-C Charging Cable
- User Manual
3. Product Overview
Familiarize yourself with the components of your QCY Melobuds N50 earphones:
Earbud Components:
- LED Indicator: Shows status (pairing, charging).
- Touch Panel: For controlling playback, calls, and modes.
- Microphone (Mic): For calls and voice commands.
- Pogo Pins: Charging contacts that connect with the charging case.
Charging Case Components:
- Earbud Slots: For storing and charging the earbuds.
- Type-C Charging Port: For charging the case.
- LED Indicator: Shows charging status of the case.
4. Setup
4.1 Choosing Eartips
For the best audio experience and secure fit, choose the eartips that best fit your ears. It is recommended to start with the medium-sized eartips as they fit most people.
4.2 First-Time Connection
- Pick up both earbuds from the charging case. If they have isolation films on the charging contacts, remove them.
- Push the earbuds back into the case and close the lid to activate them.
- Open the lid again and take out both earbuds. They will automatically enter pairing mode.
- On your smartphone, go to Bluetooth settings, search for "QCY Melobuds N50", and tap to connect.
4.3 Multi-Point Connection
Your QCY Melobuds N50 can connect to two devices simultaneously.
- Ensure earbuds are powered on and connected to Device A.
- Turn off Bluetooth on Device A. The earbuds will re-enter pairing mode.
- On Device B, search for "QCY Melobuds N50" in Bluetooth settings and tap to connect.
- On Device A, turn Bluetooth back on and tap "QCY Melobuds N50" in the list of paired devices to complete the multi-point connection.

Multipoint Connection with a Phone and Tablet
4.4 Factory Reset
If you experience connection issues, you can perform a factory reset:
- Take both earbuds out of the charging case and ensure they are disconnected from all devices.
- Tap both earbuds' touch panels 5 times simultaneously. The earbud LEDs will blink white 5 times, indicating a successful reset.
- Place the earbuds back into the case.
- Now, follow the "First-Time Connection" steps to pair them with your device again.
4.5 How to Wear
- Insert the earbuds into your ears and gently rotate them to find a comfortable and secure fit.
- Ensure the microphone is pointing towards your mouth for optimal call quality.
5. Operating Your Earphones
5.1 Power On/Off
- Power On: Open the charging case lid and take out the earbuds. Alternatively, if earbuds are outside the case and off, long-press the touch panels for 2 seconds.
- Power Off: Place the earbuds back into the charging case and close the lid.
5.2 Controls
| Function | Action |
|---|---|
| Answer/End Call | Double touch either panel |
| Ignore Call | Long press either panel for 1.5 seconds |
| Play/Pause | Double touch either panel |
| Skip Track Forward | Triple touch the right panel |
| Voice Assistant | Triple touch the left panel |
| Low Latency Mode | Long press the left panel |
| Switch ANC Mode (ANC On, ANC Off, Transparency Mode) | Long press the right panel |
5.3 Charging Earbuds
Place the earbuds into the charging case. The earbud LEDs will glow solid red while charging and turn white for 10 seconds when fully charged.
5.4 Charging Case
Connect the Type-C charging cable to the charging port on the case and to a power source. The case LED will blink white while charging and turn solid white when fully charged.
5.5 LED Indicators
Earbud LEDs:
- Solid Red: Earbuds charging.
- Solid White (10s): Earbuds fully charged.
Charging Case LEDs:
- Blinking White: Case charging.
- Solid White: Case fully charged.
- Solid White (4s, when earbuds inserted): Case has sufficient power.
- Blinking White (4s, when earbuds inserted): Case power is low.
6. Maintenance
6.1 Cleaning
- Regularly clean the charging contacts on both the earbuds and the charging case with a dry, soft cotton swab to ensure proper charging and connection.
- Clean the eartips and earbud mesh with a dry, soft cloth. Do not use oil or other volatile liquids.
6.2 Battery Care
- If the product is not used for an extended period (more than 2 weeks), please recharge it.
- Do not disassemble or modify the battery.
- Avoid exposing the battery to extreme temperatures (below 0°C or above 45°C).
6.3 Storage
- Store the earphones in their charging case when not in use to protect them and keep them charged.
- Keep the product away from direct sunlight, heat sources, and humidity.
7. Troubleshooting
If you encounter any issues with your QCY Melobuds N50, please refer to the solutions below:
- Only one earbud has sound: Place both earbuds back into the charging case, close the lid, then take them out again. If the issue persists, perform a factory reset.
- Phone cannot connect to earphones: Delete the pairing record for "QCY Melobuds N50" from your phone's Bluetooth settings. Then, search and pair again.
- No sound during music playback or calls: For Android phones, check the Bluetooth settings for "QCY Melobuds N50" and ensure "Phone audio" and "Media audio" are enabled. If still no sound, re-pair the earphones with your phone.
- Video/game latency: Latency can occur due to environmental factors, network conditions, and phone codecs. Try activating the Low Latency Mode (long press left panel).
- Sound stuttering/disconnection: Interference from strong Wi-Fi, 5G/4G signals, or high-power appliances in the vicinity can cause stuttering. Try moving to a different environment or re-pairing the earphones.
- One earphone not charging: Ensure the charging contacts on both the earbud and the case are clean and free from debris. Gently adjust the earbud in the case to ensure proper contact.
8. Specifications
| Feature | Specification |
|---|---|
| Brand Name | QCY |
| Model | Melobuds N50 |
| Material | ABS, Plastic |
| Battery Capacity | 380mAh (Case) |
| Battery Life (up to) | 28 hours (with charging case) |
| Voice Assistant Built-in | Yes |
| Maximum Wireless Range | 10m-20m |
| Sound Isolating | Yes |
| Earcups Type | Sealed |
| Number Of Drivers | 6 |
| Driver Diameter | 12mm |
| Bluetooth Version | 5.4 |
| Charging Method | Charging case (Type-C) |
| Features | Waterproof, Active Noise Cancelling, Dual Connection, Playback Control |
| Codecs | sbc |
| With Microphone | Yes (6-mic AI Call) |
| Waterproof | Yes |
| Active Noise-Cancellation | Yes (Adaptive ANC, -45dB) |
| Communication | Wireless |
| Certification | CE, FCC, RoHS, BQB |
9. User Tips
- Enhance Your Experience: Download the official QCY app to unlock full features and customize your listening experience. Users report excellent audio and noise cancellation when using the app.
- Check Charging Contacts: If one earbud isn't charging, ensure the charging contacts on both the earbud and inside the case are clean and making proper contact.
- Great Value: Many users find the sound quality to be excellent for the price point.
10. Safety Information
- Read this user manual carefully before using the product.
- Do not disassemble or modify the battery, insert foreign objects, or expose it to high temperatures.
- Avoid dropping, crushing, or puncturing the battery.
- Do not expose the product to extreme temperatures (below 0°C or above 45°C).
- Do not use the product during thunderstorms.
- Do not use oil or other volatile liquids to clean the product.
- Avoid using the device at high volume for extended periods to prevent hearing damage.
11. Warranty and Support
Your QCY product is covered by a one-year limited manufacturer warranty from the date of delivery. Please retain your purchase receipt as proof of purchase. For detailed warranty terms, service claims, or technical support, please refer to the warranty card included in your package or contact your authorized dealer.
Certifications:
This device complies with CE, FCC, RoHS, and BQB standards.