EPever DR3210N-DDS

Contents

EPEVER DuoRacer Series MPPT Dual Battery Solar Charge Controller User Manual

Model: DR3210N-DDS (and other models in the DuoRacer series)

This manual provides essential information for the safe and efficient use of your EPEVER MPPT Dual Battery Solar Charge Controller.

1. Introduction

The DuoRacer MPPT charge controller is designed for simultaneously charging two batteries: a main battery (BATT1) and a starter battery (BATT2) within a solar system. It supports various main battery types including Sealed, Gel, Flooded, LiFePO4, and Li-NiCoMn, making it suitable for applications such as RVs, campers, and boats. The controller automatically identifies the starter battery (BATT2) system voltage and initiates charging when conditions are met.

Utilizing an advanced MPPT control algorithm, the controller minimizes power loss and tracking time, ensuring maximum energy harvest from the PV array. This technology can increase energy utilization by 20-30% compared to PWM charging methods.

The device features an AES control signal for car refrigerators, allowing surplus solar power to be directed to the refrigerator, preventing energy waste. It boasts an IP33 protection level for water and dust resistance and includes multiple safety protections such as battery overcharge, over-discharge, and reverse connection protection for both PV and battery, ensuring system safety and longevity.

Key Features:

  • Maximum Power Point Tracking (MPPT) technology with ultra-fast tracking speed (≥99.5% efficiency).
  • Advanced MPPT control algorithm to optimize power point tracking.
  • Wide MPP operation voltage range for improved PV module utilization.
  • Auto-control function for charging power and current limitation (BATT1).
  • High-quality components (ST, TI, Infineon) for extended product life.
  • Digital circuit control with adaptive three-stage charging mode for enhanced BATT1 life.
  • Low-power mode activation when idle or charging conditions are not met (PV < 5V).
  • 100% charging and discharging within the operational environmental temperature range.
  • Optional LED and LCD units for system parameter display and setting.
  • AES control signal for car refrigerators to prevent energy waste.
  • Standard Modbus protocol and RS485 (5V/200mA) communication port for expanded application areas.
Infographic highlighting key features of the EPEVER MPPT Dual Battery Solar Charge Controller
Figure 1.1: Key Features Infographic
This image highlights the controller's benefits, including smart energy management, high efficiency, and suitability for various solar applications like solar cars, backpacks, and boats.

Note on Batteries:

  1. The Main battery (BATT1) is the energy storage battery for household loads in off-grid systems. It supports Sealed, Gel, Flooded, LiFePO4, and Li-NiCoMn batteries. The controller does NOT automatically identify the system voltage for BATT1.
  2. The Starter battery (BATT2), typically found in vehicles, is for powering systems like RVs and boats. It ONLY supports lead-acid batteries, and the controller automatically identifies its system voltage.

⚠ CAUTION: BATT1 and BATT2 must be at the same voltage level.

2. Important Safety Instructions

Please read and reserve this manual for future reference. Adhere to all instructions and warnings carefully before installation and operation.

  • No user-serviceable components are inside the controller. Do NOT disassemble or attempt to repair the controller.
  • Avoid direct sunlight and high temperatures. Do NOT install the controller in locations where water can enter.
  • Install the controller in well-ventilated areas. The heat sink may become very hot during operation.
  • Do not install the controller in humid, salt spray, corrosive, greasy, flammable, explosive, or dusty environments.
  • Appropriate external fast-acting fuses or breakers are recommended.
  • Before installation and adjustment, cut off all PV array connections and disconnect fast-acting fuses or breakers close to the battery.
  • Ensure power connections remain tight to prevent excessive overheating from loose connections.
  • Be extremely careful when installing batteries, especially flooded lead-acid batteries. Wear eye protection and have fresh water available to rinse if contact with battery acid occurs.
  • Keep batteries away from metal objects to prevent short circuits.
  • Ensure good ventilation, as explosive battery gases may be released during charging.
  • For outdoor installations, protect the controller from direct sunlight and rain.
  • Loose or corroded wires can generate high heat, potentially melting insulation or causing fires. Ensure all connections are tight, use cable clamps to secure wires, and prevent them from swaying in mobile applications.

3. Product Components and Appearance

Familiarize yourself with the controller's physical layout and connection points.

Labeled diagram of the EPEVER MPPT Dual Battery Solar Charge Controller
Figure 3.1: Controller Appearance and Components
This diagram identifies the key physical features and connection terminals of the DuoRacer series controller.
Controller Component Descriptions
No. Component Description
1Mounting holeSize Ø5mm for secure installation.
2LCDLiquid Crystal Display for status and settings (refer to Chapter 5).
3Grounding TerminalFor system grounding.
4Remote temperature sensor portConnects to the remote temperature sensor (RTS).
5PV terminalsConnects to the solar panel array.
6BATT1 terminalsConnects to the main battery.
7BATT2 terminalsConnects to the starter battery.
8RS485 Communication portFor communication with external devices (e.g., MT11 remote meter).
9AES (signal) output portFor connecting to car refrigerators with AES signal support.
10Terminal protection coverProtects wiring terminals.

Note: If the remote temperature sensor is not connected or is damaged, the controller will charge BATT1 at a default temperature of 25°C.

4. Installation

4.1 PV Array Requirements and Wire Size

The controller is compatible with various PV modules. The series number of PV modules can be calculated based on the open-circuit voltage (Voc) and maximum power point voltage (Vmpp) of the MPPT controller. All PV modules in a given array are assumed to be identical.

The minimum wire size is determined by the PV short circuit current (Isc). When PV modules are connected in series, the Isc equals each PV module's Isc. When connected in parallel, the Isc equals the sum of the PV modules' Isc. The Isc of the PV array must not exceed the controller's maximum PV input current.

The wiring and installation methods must conform to national and local electrical code requirements. The wire size recommendations are for reference only. For long distances between the PV array/controller or controller/battery, larger wires may be needed to reduce voltage drop. The battery cable size recommendations assume the charge controller is the only device connected to this cable.

4.2 Mounting

The controller requires sufficient airflow for heat dissipation. Ensure a minimum clearance of 150mm from the upper and lower edges for natural thermal convection.

⚠ CAUTION:

  • If installing in a closed enclosure, ensure reliable heat dissipation within the box.
  • Risk of explosion: Never install the controller in a sealed enclosure with flooded batteries or in a confined area where battery gas can accumulate.
  • Risk of electric shock: Disconnect the breaker before wiring, as the PV array may generate a high open-circuit voltage.

Refer to the PDF manual (page 17) for detailed mounting hole dimensions and placement diagrams for your specific model.

4.3 Wiring Steps

Follow these steps carefully to wire the controller. Incorrect wiring can cause damage.

⚠ CAUTION:

  • BATT1 and BATT2 must be at the same voltage level.
  • While wiring, do NOT connect the breaker or fast-acting fuse. Ensure correct electrode polarity.
  • A fast-acting fuse (1.25 to 2 times the rated current of the controller) must be installed on the battery side, no more than 150mm from the battery.
  • If an inverter is connected to the system, connect it directly to the battery.
  1. Step 1: Connect Batteries (BATT1 and BATT2)
    Connect the main battery (BATT1) and starter battery (BATT2) to their respective terminals on the controller. Ensure correct polarity.
  2. Step 2: Connect PV Array
    Connect the PV array to the PV terminals on the controller. Ensure correct polarity.
  3. Step 3: Grounding
    The DuoRacer N series controllers are common-negative. All negative terminals of the PV array and battery can be grounded simultaneously, or any one of the negatives can be grounded. However, the grounding terminal on the controller's shell MUST be grounded to shield electromagnetic interference and prevent electric shock.

    ⚠ WARNING:

    A common-negative controller for common-negative systems is recommended. However, the controller may be damaged if common-negative equipment is used and its positive electrode is grounded in the common-negative system.

  4. Step 4: Connect Remote Temperature Sensor (Optional)
    Connect the remote temperature sensor cable to port 4 on the controller and place the other end close to BATT1.

    ⚠ CAUTION:

    If the remote temperature sensor is not connected, the default temperature for battery charging/discharging is 25°C without temperature compensation.

  5. Step 5: Connect Remote Meter (MT11) and AES Signal (Optional)
    Connect the MT11 remote meter and/or the AES signal cable for refrigerator control. Refer to the MT11 user manual for remote meter operations.
    Wiring diagram for EPEVER solar charge controller with MT11 and AES-ADP
    Figure 4.1: System Wiring Diagram
    This diagram illustrates the connections for PV, Main Battery, Start Battery, MT11 remote meter, and AES-ADP to a refrigerator.

    For DR1106/2106/3106N-DDB/DDS models, the AES port (12V/200mA) and RS485 port (5V/200mA) are independent. The AES output voltage is the battery voltage.

    For DR1206/2206/3206/2210/3210N-DDB/DDS models, the AES port and RS485 port share 5VDC/Max. 200mA power. An optional AES-ADP adapter is necessary to convert the 5V-AES signal to a 12V-AES signal for the refrigerator. Refer to the PDF manual (page 13) for details on the AES-ADP adapter.

  6. Step 6: Power On the Controller
    1. First, turn on the BATT2 safety switch and check the BATT2 charging indicator status.
    2. Then, turn on the BATT1 safety switch and check the BATT1 charging indicator status.
    3. Lastly, connect the PV array circuit breaker.

    ⚠ CAUTION:

    If the controller is not operating properly or the battery indicator shows an abnormality, refer to the "Troubleshooting" section (Chapter 8).

5. Operation and Display Units

The DuoRacer series controllers come with either a Basic (DDB) or Standard (DDS) display unit. This section explains how to interpret the indicators and navigate the display.

5.1 DuoRacer Display Basic (DDB)

The DDB unit uses LED indicators to show the controller's status.

EPEVER MPPT Dual Battery Solar Charge Controller with DDB display
Figure 5.1: Controller with Basic Display (DDB)
The DDB display provides essential status information via LED indicators.
DDB Status Indicators
Indicator Color Status Instruction
MPPGreenOFFNo charging
MPPGreenSlowly flashing (1Hz)Charging, in Boost or Equalize charging stage
MPPGreenOn solidFull, in Float charging stage
TEMPRedOFFBATT1 Temperature normal
TEMPRedFast flashing (4Hz)BATT1 over-temperature or BATT1 low temperature
STATEGreenOn solidConnect to BATT1 and in charging
STATEGreenSlowly flashing (0.2Hz)Connect to BATT1 and no charging
LOWGreenOFFNot connect BATT1
LOWRedOn solidBATT1 over-discharged/Low voltage
LOWRedOFFBATT1 low voltage reconnect
AES SignalGreenOn solidAES signal is ON
AES SignalGreenOFFAES signal is OFF
BATT2 STATEGreenOn solidConnect to BATT2 and in charging
BATT2 STATEGreenSlowly flashing (1Hz)Connect to BATT2 and no charging
BATT2 STATEGreenOFFNot connect BATT2

Battery Type Indicator (DDB)

The DDB display also indicates the selected battery type. The controller cannot identify the system voltage when the battery type is lithium.

DDB Battery Type Indicators
Indicator Color Status Instruction
SEAL (Sealed)GreenOn solid12V system
SEAL (Sealed)GreenFlashing24V system (Note: DR1106/2106/3106N-DDB/DDS models do not support 24V battery)
GEL (Gel)RedOn solid12V system
GEL (Gel)RedFlashing24V system (Note: DR1106/2106/3106N-DDB/DDS models do not support 24V battery)
FLD (Flooded)GreenOn solid12V system
FLD (Flooded)GreenFlashing24V system (Note: DR1106/2106/3106N-DDB/DDS models do not support 24V battery)
LiFePO4RedOn solid12V system
LiFePO4RedFlashing24V system (Note: DR1106/2106/3106N-DDB/DDS models do not support 24V battery)
Li-NiCoMnGreenOn solid12V system
Li-NiCoMnGreenFlashing24V system (Note: DR1106/2106/3106N-DDB/DDS models do not support 24V battery)

Setting Battery Type (DDB)

  1. Press and hold the button for 3 seconds. The green BATT SEL MODE indicator will be solid. This enters the battery setting mode.
  2. Press the button to cycle through and select the desired battery type.
  3. Wait for 5 seconds until the setting indicator turns off. The battery type is successfully set.

5.2 DuoRacer Display Standard (DDS)

The DDS unit features an LCD screen for detailed information. The display is best viewed when the angle between the user's horizontal sight and the screen is within 90 degrees.

EPEVER MPPT Dual Battery Solar Charge Controller with DDS display
Figure 5.2: Controller with Standard Display (DDS)
This image shows the controller, representing the DDS display which provides comprehensive system information on an LCD screen.

Charging Indicator (DDS)

DDS Charging Indicators
Indicator Icon Color Status Instruction
Solar Panel IconGreenOn solidPV charges the battery with a low current
Solar Panel IconGreenOFFNo sunlight, Connection error, or Low PV voltage
Solar Panel IconGreenSlowly flashing (1Hz)Normal charging
Solar Panel IconGreenFast flashing (4Hz)PV overvoltage

Operation Interface Icons (DDS)

DDS Operation Interface Icons
Icon Instruction
Main Battery IconBATT1 battery capacity (0~100%)
Start Battery IconBATT2 battery capacity (0~100%)
Day IconDaytime operation
Night IconNighttime operation
PV Parameters IconDisplay PV array parameters
BATT1 Parameters IconDisplay BATT1 parameters
BATT2 Parameters IconDisplay BATT2 parameters
Temperature IconBATT1 temperature parameters
AES IconAES signal icon
Setting IconSetting icon
Batt. Type IconBattery type icon
Auto Global Browsing IconAuto global browsing icon
Min. IconMinimum voltage icon
Max. IconMaximum voltage icon
Fault IconFault icon

Changing Temperature Units (DDS)

  1. Press the MENU button under the battery temperature interface until the symbol flashes.
  2. Press the DOWN/SET button to select the temperature unit (°C or °F).

Changing Battery Type (DDS)

  1. In the battery type interface, press and hold the MENU button for 5 seconds until the symbol flashes.
  2. Press the DOWN/SET button to select the battery type.
  3. Press the MENU button to confirm the battery type.

⚠ CAUTION:

  • The battery control voltage parameters cannot be modified when the battery is set as a default type. To modify parameters, select "User" as the battery type.
  • Control parameters can only be set via PC software or mobile application.

6. Battery Charging Stages

The controller employs a three-stage battery charging algorithm for the main battery (BATT1): Bulk Charging, Constant Charging (Boost/Equalize), and Float Charging. This method extends battery lifespan.

Refer to the PDF manual (page 8, Figure 1-4) for a visual representation of the Battery Charging Stage Curve, illustrating the voltage and current behavior during Bulk, Constant, and Float charging stages.

6.1 Bulk Charging

In this stage, the battery voltage has not yet reached the constant voltage (Equalize or Boost Charging Voltage). The controller operates in constant current mode, delivering maximum current (MPPT Charging) to the batteries. Once the battery voltage reaches the constant voltage set point, the controller transitions to constant charging mode.

6.2 Constant Charging (Boost & Equalize)

When the battery voltage reaches the constant voltage set point, the controller enters constant charging mode. MPPT charging stops, and the charging current gradually decreases. This stage has two phases: Equalize Charging and Boost Charging. These are not repeated in a single full charge cycle. Equalized charging occurs on the 28th of each month.

  • Boost Charging: The default duration is typically 2 hours. Users can adjust this time. The system switches to float charging when the duration equals the set value.
  • Equalize Charging: Some battery types benefit from equalizing charging to stir electrolytes, balance voltage, and complete chemical reactions. This increases battery voltage above the standard complement voltage, gasifying the electrolyte. If automatically controlled, the equalizing charging time is 120 minutes. Equalize and boost charges are not performed constantly to prevent excessive gas precipitation or battery overheating.

⚠ WARNING: Explosive Risk!

Equalizing flooded batteries produces explosive gases. Ensure good ventilation for the battery box.

⚠ CAUTION: Equipment Damage!

  • Equalization can raise battery voltage to levels that damage sensitive DC loads. Verify that the load's allowable input voltages exceed the equalizing charging voltage.
  • Over-charging and excessive gas precipitation can damage battery plates and cause material shedding. Excessive or prolonged equalized charging can cause damage. Always review battery-specific requirements.

6.3 Float Charging

After constant charging, the controller reduces battery voltage to the float charging preset voltage by lowering the charging current. This weakly charges the battery to maintain a fully charged state. During float charging, loads can draw almost all power from the solar panel. If load power exceeds solar array power, the controller will no longer maintain the battery voltage in this stage. If the battery voltage drops below the boost voltage reconnect voltage, the system exits float charging and returns to bulk charging.

6.4 Starter Battery (BATT2) Charging

The controller trickle charges BATT2 at a 1A constant current. Charging stops when BATT2 reaches its "Full voltage" and exits constant voltage charging mode.

⚠ CAUTION:

  • BATT2 ONLY supports lead-acid battery types. Connect BATT1 first before charging BATT2.
  • Follow the logic: Full Voltage > Return Voltage when modifying voltage points.

BATT2 Start Charging Conditions:

  1. BATT2 starts charging when BATT1 reaches the float charging stage, and BATT2 voltage is lower than the "Charging Return Voltage."
  2. BATT2 starts charging when the battery's total charging current is higher than 3A, and BATT2 voltage is lower than the "Charging Return Voltage."

BATT2 Stop Charging Conditions:

  1. BATT2 stops charging when the PV voltage is no higher than 2V of BATT1.
  2. BATT2 stops charging when BATT1 is not in the float charging stage, and the total charging current for the battery is less than 2.5A.
  3. BATT2 stops charging when BATT2 reaches the "Full Voltage."

⚠ CAUTION:

After BATT2 charging is turned off, it will only be recharged when the start charging conditions are satisfied.

7. Protections

The DuoRacer series controller incorporates multiple protection features to ensure system safety and reliability.

Controller Protection Features
Protection Type Description
PV Over Current/PowerIf the PV array's charging current or power exceeds the controller's rated limits, it will operate at the rated current or power.
PV Short CircuitThe controller will not be damaged by a short circuit in the PV array when not in PV charging state.
PV Reverse PolarityThe controller may not be damaged if PV array polarity is reversed and will operate normally once corrected. NOTE: If PV array is reversed and actual power is 1.5 times rated controller's power, controller will be damaged.
Night Reverse ChargingPrevents the battery from discharging back to the PV module at night.
BATT1 and BATT2 Reverse PolarityThe controller may not be damaged if battery polarity is reversed and will resume normal operation once corrected. NOTE: For lithium batteries, if PV connection is correct but BATT1 or BATT2 polarity is reversed, the controller will be damaged.
BATT1 Over VoltageAutomatically stops battery charging when battery voltage reaches the over voltage disconnect voltage to prevent over-charging.
BATT1 Over DischargeAutomatically stops battery discharging when battery voltage reaches the low voltage disconnect voltage to prevent over-discharging. (Loads connected directly to the battery are not affected).
BATT1 OverheatingDetects battery temperature via external sensor. Stops working if temperature exceeds 65°C and restarts when below 55°C.
BATT1 Low Temperature (Lithium Battery)Stops charging/discharging if temperature is below Low Temperature Protection Threshold (LTPT). Restarts when above LTPT. (LTPT is 0°C by default, settable 10-40°C).
Controller OverheatingStops working if internal temperature exceeds 85°C and restarts when below 75°C.
TVS High Voltage TransientsInternal Transient Voltage Suppressors (TVS) protect against high-voltage surge pulses. For areas with frequent lightning, an external surge arrester is recommended.

8. Troubleshooting

This section provides solutions for common issues you might encounter with your controller.

Common Faults and Solutions
Faults Phenomenon Possible Reasons Troubleshooting
Charging LED indicator off during daytime with proper sunshine on PV modulesPV array disconnectionConfirm that PV wire connections are correct and tight.
Wire connection is correct, but controller is not workingBattery voltage is lower than 8.5VCheck battery voltage; it must be at least 8.5V to activate the controller.
DDS: Red fast flashing, Battery level shows full, battery frame blink, fault icon blinkBATT1 overvoltageCheck if battery voltage is higher than OVD (over-voltage disconnect voltage), then disconnect the PV.
DDB: Red on solid, DDS: Battery level shows empty, battery frame blink, fault icon blinkBATT1 over-dischargedWhen battery voltage is restored to or above LVR (low voltage reconnect voltage), the load will recover.
DDB: Red fast flashing, DDS: Battery level shows current capacity, battery frame blink, fault icon blink, temperature icon blink, temperature value blink, temperature unit blinkBATT1 OverheatingThe controller will automatically turn off. It will resume when temperature declines below 55°C.
DDS: Red Fast flashing and Green fast flashingBATT1 System voltage error1. Check if battery voltage matches controller's working voltage. 2. Change to a suitable battery or reset working voltage.
System voltage alarms (Lead-acid BATT1), Over-discharge alarms (BATT1 set as 24V, actual 12V), Over-voltage alarms (BATT1 set as 12V, actual 24V)Incorrect wiring - connect BATT1 first, then BATT21. Disconnect system, reconnect BATT2 first, then BATT1. 2. BATT1 voltage should be the same as controller's voltage level.

9. Maintenance

Perform the following inspections and maintenance tasks at least twice yearly for optimal controller performance.

  • Ensure the controller is firmly installed in a clean and dry environment.
  • Ensure no obstructions to airflow around the controller. Clean any dirt and fragments from the radiator.
  • Inspect all exposed wires for insulation damage (solarization, frictional wear, dryness, pests). Repair or replace damaged wires as needed.
  • Tighten all terminals. Inspect for loose, broken, or burnt wire connections.
  • Verify that LED or LCD indications are consistent with expected operation. Address any troubleshooting or error indications.
  • Confirm all system components are tightly and correctly grounded.
  • Inspect all terminals for corrosion, insulation damage, high temperature, or burnt/discolored signs. Tighten terminal screws to the suggested torque.
  • Clean dirt, nesting insects, and corrosion promptly.
  • Check the lightning arrester (if installed) for good condition. Replace it if necessary to protect the controller and other equipment.

⚠ WARNING: Risk of Electric Shock!

Ensure all power is turned off before performing any maintenance operations and follow all corresponding inspections.

10. Specifications

10.1 Electrical Parameters

DuoRacer Series Electrical Parameters
Item DR1106N-DDB/DDS DR2106N-DDB/DDS DR3106N-DDB/DDS DR1206N-DDB/DDS DR2206N-DDB/DDS DR3206N-DDB/DDS DR2210N-DDB/DDS DR3210N-DDB/DDS
BATT1 rated voltage12VDC12/24VDC Auto
BATT2 rated voltage12VDC12/24VDC Auto
BATT1 Rated Charge Current10A20A30A10A20A30A20A30A
BATT2 Rated Charge Current1A
Battery Input Voltage Range8.5~16V8.5~32V
Max. PV Open Circuit Voltage60V100V
MPP Voltage Range(Battery Voltage+2V)~36V (for 60V Max PV) / (Battery Voltage+2V)~72V (for 100V Max PV)
Rated Charge Power130W/12V260W/12V390W/12V130W/12V, 260W/24V260W/12V, 520W/24V390W/12V, 780W/24V260W/12V, 520W/24V390W/12V, 780W/24V
Max. conversion efficiency96.3%96.9%97.4%97.4%97.5%98%97.5%98%
Full load efficiency95.5%94.6%94.2%97%96%96%96%96%

10.2 Environmental Parameters

Environmental Parameters
Item DR1106/2106/3106/1206/2206/2210N-DDB/DDS DR3206/3210N-DDB/DDS
Environment temperature (100% input and output)-20°C ~ +50°C (DDS), -30°C ~ +50°C (DDB)-20°C ~ +45°C (DDS), -30°C ~ +45°C (DDB)
Storage temperature-30°C ~ +80°C
Relative humidity≤95%, N.C
EnclosureIP33 (3-protection against solid objects over 2.5mm; 3-protected against sprays to 60° from vertical)
Pollution degreePD2

10.3 Mechanical Parameters

Mechanical Parameters
Item DR1106/1206N-DDB/DDS DR2106/2206/2210N-DDB/DDS DR3106/3206/3210N-DDB/DDS
Dimension (L x W x H)227.2 x 143 x 58.1mm243.7 x 158 x 63mm247.2 x 165 x 68.5mm
Mounting size (L x W)160 x 134mm180 x 149mm180 x 156mm
Mounting hole sizeØ5mm
Terminal12AWG/4mm² (BATT1), 12AWG/4mm² (BATT2)6AWG/16mm² (BATT1), 12AWG/4mm² (BATT2)6AWG/16mm² (BATT1), 12AWG/4mm² (BATT2)
Recommended cable size12AWG/4mm² (BATT1), 12AWG/4mm² (BATT2)10AWG/6mm² (BATT1), 12AWG/4mm² (BATT2)8AWG/10mm² (BATT1), 12AWG/4mm² (BATT2)
Weight0.8kg1.1kg1.4kg

11. Dimension Diagrams

Detailed physical dimensions for various models in the DuoRacer series are provided in the PDF manual (Annex I, pages 38-40). Please refer to the PDF for precise diagrams.

11.1 DR1106/1206N-DDB/DDS (Unit: mm)

Length: 227.2mm, Width: 143mm, Height: 58.1mm. Mounting size: 160x134mm.

11.2 DR2106/2206/2210N-DDB/DDS (Unit: mm)

Length: 243.7mm, Width: 158mm, Height: 63mm. Mounting size: 180x149mm.

11.3 DR3106/3206/3210N-DDB/DDS (Unit: mm)

Length: 247.2mm, Width: 165mm, Height: 68.5mm. Mounting size: 180x156mm.

12. User Tips

Based on general user feedback and common practices for solar charge controllers:

  • Verify Battery Compatibility: Always double-check that your battery type (especially for BATT1) is correctly configured in the controller settings to ensure optimal charging and prevent damage.
  • Monitor Connections: Periodically inspect all wiring connections for tightness and signs of corrosion, especially in mobile applications like RVs, to prevent power loss and overheating.
  • Consider Remote Monitoring: If your model supports it, using the MT11 remote meter can provide convenient access to system parameters and status without needing to access the controller directly.
  • Ventilation is Key: Ensure the controller always has adequate airflow. Overheating can reduce efficiency and lifespan.

13. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official EPEVER website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

Additional Resources:

A detailed user manual in PDF format is available for download. You can find it at: EPEVER MPPT Dual Battery Solar Charge Controller User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.