Introduction
The SUNSHINE SS-601G is a heat-free mobile phone and tablet screen removal tool designed for safe and non-destructive disassembly. It utilizes a strong suction cup and screw tension design to separate screens without damaging cables or cameras, making it an essential tool for device repair.
Safety Information
- Always wear appropriate protective gloves when handling electronic devices and tools.
- Ensure the device is powered off before attempting any disassembly.
- Handle sharp tools and alcohol with care to prevent injury or damage.
- Keep the tool and any liquids away from children.
- Do not apply excessive force, as this may damage the device.
Package Contents
The package typically includes:
- 1 x SUNSHINE SS-601G LCD Screen Separator Unit
- (Additional accessories may vary based on specific purchase)
Specifications
| Attribute | Value |
|---|---|
| Model Number | SUNSHINE SS-601G |
| Type | Combination |
| Application | Computer Tool Kit |
| Size | 220*70*76mm |
| Origin | Mainland China |
| DIY Supplies | Electrical |
| Package | Case |
For detailed dimensions, refer to the diagram below:
Setup and Operation
This section provides step-by-step instructions for using the SUNSHINE SS-601G LCD Screen Separator. A video demonstration is also available below for visual guidance.
Video Guide: Screen Removal Demonstration
Step-by-Step Instructions:
-
Pre-heat the Phone (Optional, but Recommended for Strong Adhesives): Place the phone at approximately 80°C for about 3 minutes. This helps soften the adhesive holding the screen. Note: The SS-601G tool itself is heat-free, but pre-heating the device is a common practice for easier screen separation.
Figure 2: Phone placed on a heating pad for pre-heating. -
Apply Alcohol: Drip a small amount of 95%+ alcohol around the edge of the screen. Pay close attention to the LCD screen to avoid alcohol infiltration, which can cause damage.
Figure 3: Applying alcohol to the edges of the phone screen. -
Position the Phone in the Fixture: Place the phone into the SS-601G fixture. Ensure it is centered and stable.
Figure 4: Phone secured within the SS-601G fixture. -
Secure the Suction Cup: Move the suction cup to the proper position over the screen and make it hold the screen tightly. After fixing the phone, use the suction cup to absorb the screen.
Figure 5: Suction cup engaged with the phone screen. -
Begin Separation: Slowly unscrew the tension screw so that the suction cup pulls the screen upwards, separating it from the back cover. Pay attention to the screen slits as it begins to open.
Figure 6: Initial separation of the screen from the device body. -
Monitor Separation: Continue to unscrew the tension screw until the other side of the screen is opened. Observe the separation carefully to avoid damage.
Figure 7: Observing the screen separation process. -
Soften Glue (if needed): Alcohol can be added during the separation process to further soften stubborn glue.
Figure 8: Applying additional alcohol to aid in glue softening. -
Stop at Camera Vicinity: The back cover should be separated to the vicinity of the camera. There is a protective groove at the camera position to prevent damage.
Figure 9: Screen separation reaching the camera area, highlighting the protective groove. -
Release Suction Cup: When stopping the separation, be sure to loosen the tension screw before releasing the suction cup to prevent sudden detachment.
Figure 10: Loosening the tension screw to safely release the suction cup. -
Complete Separation: Gradually separate the remaining positions of the screen from the device.
Figure 11: Completing the screen separation process. -
Removal Completed: The screen or back cover removal is now completed.
Figure 12: Screen successfully removed from the device.
User Tips
- Practice Makes Perfect: Screen removal requires experience. It is recommended to practice on a non-essential device first if you are new to phone repair.
- Secure Clamping: Always ensure the phone is securely fixed in the clamp before engaging the suction cup to prevent slipping.
- Suction Cup Adhesion: For screens with cracks, applying a clear screen protector film over the cracked area can help improve the suction cup's grip. Ensure the suction cup is clean and free of debris.
- Gradual Tension: Apply tension slowly and gradually. Rushing the process can lead to damage to the screen or internal components.
- Alcohol Application: Be precise when applying alcohol to the edges to avoid it seeping into the LCD or other sensitive parts.
- Camera Groove: The tool features a protective groove for the camera. While designed for iPhone, some users suggest a wider groove could improve compatibility with other models.
Maintenance
- Cleaning: After each use, clean the tool, especially the suction cup and clamping surfaces, to remove any adhesive residue or dust. Use a soft cloth and a small amount of alcohol if necessary.
- Storage: Store the SS-601G in a dry, clean environment, away from direct sunlight and extreme temperatures.
- Inspection: Periodically inspect the screws and moving parts for any signs of wear or damage. Tighten any loose screws as needed.
Troubleshooting
- Suction cup not holding:
- Ensure the screen surface and suction cup are clean and dry.
- Check for severe cracks on the screen that might prevent a seal. Consider using a screen protector film over cracks to create a better seal.
- Apply firm, even pressure when engaging the suction cup.
- Phone slipping from clamp:
- Verify the phone is properly seated and the clamping screws are tightened sufficiently.
- Avoid sudden movements or excessive force during the separation process.
- Screen not separating easily:
- Re-apply alcohol to the edges to further soften the adhesive.
- Ensure the device was adequately pre-heated (if applicable for the device model).
- Increase tension gradually, but do not force it.
Warranty and Support
For specific warranty information, please refer to the documentation provided at the time of purchase or contact the seller directly. A detailed user manual in PDF format is also available for download: