1. Introduction
Thank you for choosing the MASTFUYI FY168S Large Screen Charging Multimeter. This intelligent multimeter is designed for efficient and accurate electrical measurements, featuring True RMS, auto-ranging, and a variety of functions including AC/DC voltage and current, resistance, capacitance, non-contact voltage (NCV) detection, diode testing, and temperature measurement. This manual provides essential information for safe and effective use of your device.

Image 1: MASTFUYI FY168S Multimeter Overview
2. Safety Information
WARNING: Improper use might cause electric shock or damage to the meter. Always follow safety rules and measures.
- Always wear appropriate personal protective equipment to avoid electric shock.
- Do not misuse the meter. Ensure the correct function and measuring range are selected for each test.
- Before use, inspect the meter and test leads for any damage to insulation or exposed metal wires. Do not use if damaged.
- Do not exceed the maximum input values for any measuring range.
- Keep fingers behind the test lead protectors when connected to a measuring circuit.
- If the measured voltage exceeds 60V DC or 30V AC (RMS), exercise extreme caution.
- Do not measure resistance, capacitance, or diodes on energized lines.
- Before changing the testing function, remove the test leads from the measuring circuit.
- Do not test capacitance before the capacitor is fully discharged.
- Do not use the meter in explosive gas, steam, or dusty environments.
- If any abnormality or malfunction occurs, stop using the meter immediately.
- Ensure the meter's bottom shell and battery cover are completely closed before use.
This meter complies with IEC-61010-1 standard, CAT III 600V over-voltage standard, and is CE certified.
3. Product Overview
3.1. Part Names
- V-Alert Sensor Area: For non-contact voltage detection.
- Flashlight: Illuminates the test area.
- Display Screen: Large color display for readings and indicators.
- Function Switching Buttons: For selecting measurement modes.
- Auto Mode: Automatically identifies AC/DC voltage, resistance, and continuity.
- Voltage Sensing (V-Alert) / Live Wire Check: For non-contact voltage and live wire detection.
- Flashlight Switching: Button to turn the flashlight ON/OFF.
- Capacitance Mode Button: For capacitance measurements.
- Diode Mode Button: For diode testing.
- Power Button: To power ON/OFF the device.
- Input Terminal: For connecting test leads.

Image 2: MASTFUYI Multimeter Functions Diagram
3.2. Button Descriptions
- Power Button: Long press for 1 second to Power ON/OFF. Short press to enable/disable auto shutdown.
- V-Alert Sensing/Live Wire Check Button: Short press to switch between low sensitivity, high sensitivity, and live wire check modes for voltage sensing.
- Auto Mode Button: Short press to switch to auto mode.
- SEL Function Switching Button: Short press to cycle through DC voltage, AC voltage, VFC (Variable Frequency Voltage), resistance, continuity, frequency, and duty cycle modes.
- Capacitance Mode Button: Short press to enter capacitance mode.
- Diode Mode Button: Short press to enter diode mode.
- Temperature Mode/Flashlight Button: Long press for 1 second to turn the flashlight ON/OFF. Short press to switch between Fahrenheit and Celsius temperature measurement modes.
3.3. Display Symbols
| Symbol | Explanation |
|---|---|
| AUTO | Automatic mode |
| DC | DC Voltage |
| AC | AC Voltage |
| V-Alert | Voltage Sensing (Non-Contact Voltage) |
| Ω | Resistance (Megohm, Kilohm, Ohm) |
| ))) | Continuity |
| --|-- | Diode mode |
| μF, mF, nF | Capacitance (Microfarad, Millifarad, Nanofarad) |
| mA | Milliamp (Current) |
| Hz, KHz | Frequency (Hertz, Kilohertz) |
| °C/°F | Celsius/Fahrenheit (Temperature) |
| LIVE | Live wire check |
| Battery Icon | Low battery indication |
| OL / -OL | Over-range display |
| Auto Power Off Icon | Automatic Power off function indication |
4. Setup
4.1. Unboxing
Upon receiving your multimeter, carefully unbox all components. The package typically includes the multimeter, test leads, a USB-Type C charging cable, and a user manual. The FY168S model also comes with a soft silicone protective cover for enhanced safety and durability.
Video 1: Unboxing and initial overview of the MASTFUYI FY168S Multimeter and accessories.
4.2. Charging the Battery
The FY168S is equipped with a built-in 400mAh lithium-ion battery. Before first use, or when the low battery indicator appears on the LCD, charge the device using the provided USB-Type C cable.
- Remove the rubber cover from the USB-Type C port located on the side of the multimeter.
- Connect the USB-Type C cable to the multimeter and the other end to a USB power source (e.g., wall adapter, computer USB port).
- During charging, a red indicator light will illuminate. It will turn green once fully charged.
- The meter is not allowed to be turned on and used during charging.

Image 3: USB-Type C Charging for the Multimeter
4.3. Attaching the Protective Cover
The FY168S model comes with a soft silicone protective cover. Carefully slide the multimeter into the cover to safeguard it against drops and enhance durability.

Image 4: Multimeter with Soft Silicone Protective Cover
5. Operating Instructions
General Steps:
- Press the Power button for 1 second to turn on the multimeter. It will typically enter AUTO mode.
- Connect the test leads to the appropriate input terminals for your measurement.
- Select the desired measurement mode using the function buttons or rely on AUTO mode.
- Perform the measurement and read the value on the display.
- Disconnect the test leads from the circuit when measurement is complete.
5.1. Auto Mode
In AUTO mode, the multimeter automatically identifies and measures AC/DC voltage, resistance, and continuity. This is ideal for quick checks when the type of measurement is unknown.
5.2. Specific Measurements
For specific measurements, you can either rely on AUTO mode (for voltage, resistance, continuity) or manually select the function using the SEL button.
- DC Voltage: Connect the test leads to the circuit. The meter will display the DC voltage. (Refer to Video 1, segment 0:14 for demonstration).
- AC Voltage: Connect the test leads to the AC source. The meter will display the AC voltage. (Refer to Video 1, segment 0:17 for demonstration).
- DC Current: Connect the test leads in series with the DC circuit. The meter will display the DC current. (Refer to Video 1, segment 0:24 for demonstration).
- AC Current: Connect the test leads in series with the AC circuit. The meter will display the AC current. (Refer to Video 1, segment 0:28 for demonstration).
- Resistance (Ω): Connect the test leads across the component. The meter will display the resistance. (Refer to Video 1, segment 0:32 for demonstration).
- Capacitance (F): Ensure the capacitor is fully discharged before testing. Connect the test leads across the capacitor. The meter will display the capacitance. (Refer to Video 1, segment 0:36 for demonstration).
- Diode: Connect the test leads across the diode. The meter will display the forward voltage drop. (Refer to Video 1, segment 0:41 for demonstration).
- Live Wire Check: Insert the red test lead into the live terminal of an outlet. The meter will indicate a live wire with an audible alarm and red backlight. (Refer to Video 1, segment 0:45 for demonstration).
- NCV (Non-Contact Voltage) / V-Alert: Hold the top of the meter close to an AC power source. The meter will sound an alarm and change backlight color when AC voltage is sensed. Short press the V-Alert button to switch between low (LO) and high (HI) sensitivity.

Image 5: NCV V-Alert Function Explanation (Low and High Sensitivity)
- Flashlight: Short press the Temperature/Flashlight button to turn the flashlight ON/OFF. (Refer to Video 1, segment 0:51 for demonstration).
- Temperature: Connect a K-type thermocouple (if included or purchased separately) to the input terminals. Short press the Temperature/Flashlight button to switch between Celsius and Fahrenheit. (Refer to Video 1, segment 1:19 for demonstration).
6. Maintenance
6.1. General Maintenance
- Do not operate the product near hot, wet, flammable, explosive, or magnetic environments.
- Clean the product with a damp cloth and mild detergent. Do not use abrasives or solvents.
- Remove input signals before cleaning the product.
- If the product will not be used for a long time, remove the batteries to prevent possible battery leakage.
6.2. Battery Charging
When the low battery symbol appears on the display, the battery needs to be charged. Follow the charging instructions in Section 4.2.
7. Troubleshooting
This section addresses common issues you might encounter with your multimeter.
- No Display / Device Not Turning On: Ensure the battery is charged. If the battery is low, charge it as per Section 4.2.
- "OL" or "-OL" on Display: This indicates an over-range condition. The measured value exceeds the selected range. Switch to a higher range or ensure the component is within the meter's capabilities.
- Inaccurate Readings: Check that the test leads are securely connected and not damaged. Ensure the correct measurement mode is selected. Verify that the component being tested is not energized when measuring resistance, capacitance, or diodes.
- No NCV/V-Alert Response: Ensure the NCV function is activated and the sensor area is directly over the AC source. Check sensitivity settings (LO/HI).
- Device Freezes or Behaves Erratically: Turn off the device and then turn it back on. If the issue persists, ensure the battery is fully charged.
If you experience persistent issues not covered here, please contact customer support.
8. Specifications (FY168S)
Test conditions: environmental temperature 18°C to 28°C, relative humidity <80%RH.
| Function | Range | Resolution | Accuracy |
|---|---|---|---|
| General | |||
| Display Type | Digital Display (Color Screen) | ||
| Max Display Value | 6000 counts | ||
| Operating Mode | Auto range | ||
| Sampling Time | Approx. 0.4 seconds | ||
| Auto Power Off | 15 minutes (no signal input) | ||
| Battery | 3.7V Li-ion battery (400mAh) | ||
| Operating Altitude | 2000m | ||
| Dimensions | 146 x 44 x 25.2 mm | ||
| Weight | 95g (with sheath) | ||
| Certifications | CE, FCC | ||
| Measurement Functions | |||
| DC Voltage | 0.005V - 620V | 0.001V | ±(0.8% + 3 counts) |
| AC Voltage | 0.005V - 620V | 0.001V | ±(1.2% + 5 counts) |
| DC Current | 1.0mA - 610mA | 0.1mA | ±(1.5% + 3 counts) |
| AC Current | 1.0mA - 610mA (40-1000Hz) | 0.1mA | ±(1.5% + 3 counts) |
| Resistance | 0.0Ω - 60.00MΩ | 0.1Ω - 0.01MΩ | ±(1.2% + 3 counts) to ±(2.0% + 10 counts) |
| Capacitance | 0.5μF - 60.00mF | 0.001μF - 0.01mF | ±(3.5% + 8 counts) to ±(4.5% + 10 counts) |
| Frequency | 0Hz - 9999Hz | 0.1Hz | ±(2.0% + 10 counts) |
| Temperature | -50°C to 1000°C (-58°F to 1832°F) | 1°C (1°F) | ±(2.0% + 3°C/°F) |
| NCV Sensing | Low (LO) / High (HI) sensitivity indication with visual and audible alerts. | ||
Note: The FY168S features a color display with backlight always on, unlike the FY167 and FY168 models which have ordinary LCDs where the backlight can be turned on/off. The FY167 and FY168 also have a voltage alert that turns the screen red when measured voltage exceeds 90V, a feature not explicitly stated for FY168S but implied by NCV.

Image 6: Comparison of FY167, FY168, and FY168S displays and features.
9. User Tips
- Start with Auto-Ranging: For unknown voltage or resistance values, begin with the auto-ranging feature to prevent damage to the meter and ensure accurate initial readings.
- Secure Connections: Always ensure your test leads are firmly plugged into the correct input terminals and make good contact with the circuit points you are testing. Loose connections can lead to inaccurate readings or safety hazards.
- Utilize NCV for Safety: Before touching any wires or components, use the NCV (Non-Contact Voltage) function to quickly check for the presence of AC voltage. This is a crucial safety step.
- Discharge Capacitors: Always discharge capacitors before measuring their capacitance or working on circuits containing them to avoid electric shock and damage to the meter.
- Read the Display Carefully: Pay attention to units (V, mV, A, mA, Ω, kΩ, MΩ, F, nF, μF, mF, Hz, KHz, °C, °F) and any warning indicators like "OL" or the low battery symbol.
10. Warranty and Support
For detailed warranty information, technical support, or service inquiries, please contact the seller or refer to the official product documentation. You can find the full user manual in PDF format for more in-depth information: