EPever TRIRON N Series

Contents

TRIRON N Series Modular MPPT Solar Charge Controller

User Manual

1. Introduction

1.1 Overview

The TRIRON N series controllers are modular-designed products based on six MPPT solar controller models. The main unit (Power Module) (TRIRON-N) is a solar controller which can be integrated with different display and interface modules to meet a variety of functional requirements. The TRIRON N series controllers can automatically identify and load the drivers of various modules. There are three display modules (Basic 1(DB1), Standard1 (DS1) and Standard2(DS2)) and four interface modules (USB COM Slave (UCS), Relay COM Slave (RCS), Relay COM Master(RCM) and Dual USB1(USB1)). Users can choose any combination of these modules according to their needs.

With the advanced MPPT control algorithm, TRIRON N series controllers can minimize the maximum power point loss rate and loss time, quickly track the maximum power point of the PV array and obtain the maximum energy from solar modules under any conditions; and can increase the ratio of energy utilization in the solar system by 10%-30% compared with a PWM charging method. With the adaptive three-stage charging mode based on a digital control circuit, TRIRON N series controllers can effectively prolong the lifecycle of batteries, significantly improve the system performance and support all-around electronic protection functions, including overcharging and over-discharging protection to minimize damages to components of the system caused by incorrect installation or system failure at the utmost, and effectively ensure safer and more reliable operation of the solar power supply system for a longer service time. This modular solar controller can be widely used for different applications, e.g., communication base stations, household systems, street lighting systems and field monitoring, etc.

1.2 Characteristics

The TRIRON N series controllers offer the following features:

  • Identify and load the drivers of various modules automatically.
  • Support the hot swapping function without any damage for each module.
  • Modular design for easy combination and replacement.
  • Advanced MPPT control algorithm to minimize the maximum power point loss rate and loss time.
  • Advanced MPPT technology, with efficiency no less than 99.5%.
  • High quality components, perfecting system performance, with maximum conversion efficiency of 98%.
  • Ultra-fast tracking speed and guaranteed tracking efficiency.
  • Automatic limitation of the charging power and current.
  • Wide MPP operating voltage range.
  • Multiple load work modes.
  • Compatible with lead-acid and lithium-ion batteries.
  • Battery temperature compensation function.
  • Real-time energy statistics function.
  • Overheating power reduction function.
  • LCD and indicators to display operating data and status of the system.
  • User-friendly buttons for comfortable and convenient operation.
  • Master and slave RS485 communication modules design, reading the load or inverter operating data.
  • Control the inverter switch through the relay interface.
  • Provide 5VDC power through the dual USB output interface to charge electronic devices.
Front view of the Epever TRIRON N Series MPPT Solar Charge Controller.
Front view of the Epever TRIRON N Series MPPT Solar Charge Controller. This image shows the main unit with its display, buttons, USB ports, RS485 port, and terminal connections.

1.3 Module Types

The TRIRON N series controllers are modular, allowing for various configurations. The main Power Module can operate independently. If display or interface modules are installed, they are powered by the Power Module.

1.3.1 Power Modules

Power Modules control PV battery charging and load discharging. They can operate without any display or interface modules. The following table outlines the different power module models:

ModelSystem VoltageMax. PV Open Circuit VoltageRated Charge/Discharge Current
TRIRON1206N12/24VDC60V10A
TRIRON2206N12/24VDC60V20A
TRIRON1210N12/24VDC100V10A
TRIRON2210N12/24VDC100V20A
TRIRON3210N12/24VDC100V30A
TRIRON4210N12/24VDC100V40A
TRIRON4215N12/24VDC150V40A

1.3.2 Display Modules

Display modules provide visual feedback and control options for the system.

ModuleDescription
Display Basic1 (DB1)LED Indicators: PV & battery working status. Button: When the working mode is Manual Control, the load is ON/OFF via the button.
Display Standard 1 (DS1)LED Indicators: PV & load working status. Buttons: View or set the parameters. LCD: PV display: voltage/current/generated energy. Battery display: voltage/current/temperature. Load: Display current/load working mode when the controller communicates with the PC or APP. Display voltage/current/power consumption when the controller communicates with the inverter.
Display Standard 2 (DS2)Indicators: PV & battery & load working status. Buttons: View or set the parameters. LCD: PV display voltage/current/generated energy/Power. Battery display voltage/current/temperature/capacity. Load: Display voltage/current/power/load working mode when the controller communicates with the PC or APP. Display voltage/current/power power consumption when the controller communicates with the inverter.
No Display Cover (DCV)No indicator or display.

1.3.3 Interface Modules

Interface modules provide communication and additional functionality.

ModuleFunction
USB COM Slave (UCS)RS485 interface: Connect to PC or phone. View or change the controller parameters. USB interface: Supplies 5VDC for electronic equipment. NOTE: USB interface is output when the load is ON.
Relay COM Master (RCM)RS485 interface: Connect to inverter. View the inverter parameters via the LCD. Relay interface: Remotely control the inverter ON/OFF. Accessory: 3.81-2P terminal.
Relay COM Slave (RCS)RS485 interface: Connect to PC or phone. View or change the controller parameters. Relay interface: Remotely control the inverter ON/OFF. Accessory: 3.81-2P terminal.
Double USB (USB1)Supplies 5VDC for electronic equipment. NOTE: USB interface is output when the load is ON.
No COM Cover (CCV)No interface.

1.4 Designations of Controller Models

The model designation provides information about the controller's configuration:

Diagram illustrating the model designation structure for TRIRON N series controllers.
Diagram illustrating the model designation structure for TRIRON N series controllers. This image shows how the model name breaks down into Power Module, Display Module, and Interface Module components, along with system voltage, current, and PV open circuit voltage.

1.5 Accessories (optional)

Various optional accessories can enhance the functionality of your TRIRON N series controller:

AccessoryDescription
Remote Temperature Sensor (RTS300R47K3.81A)Acquisition of battery temperature for undertaking temperature compensation of control parameters. Standard cable length is 3m (customizable). Connects to the 4th port on the controller. NOTE: If the temperature sensor is short-circuited or damaged, the controller will charge or discharge at the default temperature of 25°C.
USB to RS485 cable (CC-USB-RS485-150U)Used to monitor each controller on the network using Solar Station PC software. Cable length is 1.5m. Connects to the RS-485 Port on the controller.
OTG cable (OTG-12CM)Used to connect a mobile communication cable for real-time monitoring and parameter modification via mobile APP software.
Remote Meter (MT50)Displays various operating data and system faults on a backlit LCD screen. Features easy-to-operate buttons and readable numeric display.
WIFI Serial Adapter (eBox-WIFI-01)After connecting to the controller via a standard Ethernet cable, the operating status and parameters can be monitored by mobile APP software via WIFI signals.
RS485 to Bluetooth Adapter (eBox-BLE-01)After connecting to the controller via a standard Ethernet cable, the operating status and parameters can be monitored by mobile APP software via Bluetooth signals.
Logger (eLOG01)After connecting to the controller via an RS485 communication cable, it can record operating data or monitor real-time operating status via PC software.

NOTE: For detailed setting and operation of accessories, please refer to their respective instructions.

Wiring diagram showing the TRIRON N series controller connected to solar panels, battery, load, and various optional accessories like MT50 remote meter, eBox-WIFI-01, eBox-BLE-01, and a PC/phone via USB/RS485.
Wiring diagram showing the TRIRON N series controller connected to solar panels, battery, load, and various optional accessories like MT50 remote meter, eBox-WIFI-01, eBox-BLE-01, and a PC/phone via USB/RS485. This diagram illustrates the various connection points and compatible devices.

2. Important Safety Instructions

Please save this manual for future review. This manual contains safety, installation, and operation information for the Maximum Power Point Tracking (MPPT) TRIRON N series controller.

General Safety Information

  • Read carefully all instructions and warnings in the manual before installation.
  • No user serviceable components inside the controller. DO NOT disassemble or attempt to repair the controller.
  • Mount the controller indoors. Prevent exposure to the elements and do not allow water to enter the controller.
  • Install the controller in a well-ventilated place. The controller's heat sink may become very hot during operation.
  • It is suggested to install appropriate external fuses/breakers.
  • Make sure to switch off all PV array connections and the battery fuse/breakers before controller installation and adjustment.
  • Power connections must remain tight to avoid excessive heating from loose connections.

3. Setup and Installation

3.1 General Installation Notes

  • Please read the entire installation instructions to get familiar with the installation steps before installation.
  • Be very careful when installing the batteries, especially flooded lead-acid battery. Please wear eye protection, and have fresh water available to wash and clean any contact with battery acid.
  • Keep the battery away from any metal objects, which may cause short circuit of the battery.
  • Explosive battery gases may come out from the battery during charging, so make sure ventilation condition is good.
  • Ventilation is highly recommended if mounted in an enclosure. Never install the controller in a sealed enclosure with flooded batteries! Battery fumes from vented batteries will corrode and destroy the controller circuits.
  • Loose power connections and corroded wires may result in high heat that can melt wire insulation, burn surrounding materials, or even cause fire. Ensure tight connections and use cable clamps to secure cables and prevent them from swaying in mobile applications.
  • Lead-acid battery and lithium battery are recommended, other kinds please refer to the battery manufacturer.
  • Battery connection may be wired to one battery or a bank of batteries. The following instructions refer to a singular battery, but it is implied that the battery connection can be made to either one battery or a group of batteries in a battery bank.
  • Multiple same models of controllers can be installed in parallel on the same battery bank to achieve higher charging current. Each controller must have its own solar module(s).
  • Select the system cables according to 5A/mm² or less current density in accordance with Article 690 of the National Electrical Code, NFPA 70.

3.2 PV Array Requirements

As the core component of PV system, controller could be suitable for various types of PV modules and maximize converting solar energy into electrical energy. According to the open circuit voltage (Voc) and the maximum power point voltage (Vmpp) of the MPPT controller, the series number of different types PV modules can be calculated. The table in the full user manual is for reference only.

3.3 Wire Size

Detailed information on appropriate wire sizing for your installation can be found in the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

3.4 Mounting

Instructions for mounting the controller are provided in the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

3.5 Installing the Modules

Guidance on how to install the various modules (display, interface) is detailed in the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

4. Operating Instructions

4.1 Display Module Operation

The display modules (DB1, DS1, DS2) provide visual information and allow for parameter adjustments. Refer to the 'Module Types' section above for a summary of each display's capabilities. Detailed operation instructions for each display module, including button functions and LCD navigation, are available in the full PDF user manual.

Close-up view of the controller's display module with buttons (PV/+, BATT/-, LOAD/-, SET, U/ESC).
Close-up view of the controller's display module with buttons (PV/+, BATT/-, LOAD/-, SET, U/ESC). This image highlights the user interface for interacting with the controller.
Display screens of the TRIRON N series controller showing various parameters like voltage, current, power, energy, and battery type.
Display screens of the TRIRON N series controller showing various parameters like voltage, current, power, energy, and battery type. This image demonstrates the range of information available to the user.

4.2 Interface Module Operation

Interface modules like USB COM Slave, Relay COM Master, Relay COM Slave, and Double USB provide connectivity for monitoring, control, and charging external devices. Refer to the 'Module Types' section for a summary of each interface's functions. Detailed usage instructions for each interface module are available in the full PDF user manual.

Close-up view of the controller's USB ports (5V Max. 2.2A) and RS485 SLAVE port.
Close-up view of the controller's USB ports (5V Max. 2.2A) and RS485 SLAVE port. This image shows the physical connections for data communication and device charging.

4.3 Setting Control Parameters

The controller allows for various parameters to be set, including battery types and load working modes. Detailed instructions on how to access and modify these settings are provided in the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

4.4 Load Working Modes

The controller supports multiple load working modes. Information on configuring and understanding these modes, including LCD and RS485 communication settings, can be found in the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

5. Maintenance

Regular maintenance is crucial for the longevity and optimal performance of your solar charge controller. Detailed maintenance procedures, including inspection points and cleaning instructions, are outlined in the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

6. Troubleshooting

This section provides guidance on identifying and resolving common issues that may arise with your TRIRON N series controller. For a comprehensive troubleshooting guide, including error codes and solutions, please refer to the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

7. Specifications

The Epever TRIRON N Series MPPT Solar Charge Controller features:

  • Brand Name: EPever
  • Model Numbers: TRIRON2210N, TRIRON3210N, TRIRON4210N (and others in the series)
  • Maximum Current: 20A, 30A, 40A (depending on model)
  • Application: Charger Controller, Voltage Controller, Solar System Controller, Solar Working Station, Lighting Controller
  • Is Smart Device: Yes
  • is_customized: Yes
  • Origin: Mainland China
  • Certification: CE

For detailed technical specifications, including electrical parameters, environmental conditions, and physical dimensions, please consult the full PDF user manual available at Epever TRIRON N Series User Manual (PDF).

8. User Tips

To ensure optimal performance and longevity of your TRIRON N Series MPPT Solar Charge Controller, consider the following general tips:

  • Always ensure proper ventilation around the controller to prevent overheating, especially during high-load operation.
  • Double-check all wiring connections for tightness and correct polarity before powering on the system. Loose connections can lead to performance issues or safety hazards.
  • Regularly monitor the display for system status and any error indicators. Understanding the display information can help in early detection of potential problems.
  • If using optional communication modules, ensure the software (PC or mobile app) is up-to-date for the best compatibility and features.
  • For specific battery types, ensure the correct battery parameters are set in the controller to optimize charging and extend battery life.

For more specific user tips and community-shared advice, refer to the comprehensive user manual or online forums dedicated to Epever products.

9. Warranty and Support

For information regarding product warranty, technical support, and service, please refer to the official Epever documentation or contact your point of purchase. The full user manual contains important details regarding product guarantees and how to obtain assistance.

A comprehensive PDF version of this user manual, including detailed diagrams, tables, and advanced instructions, is available for download: Epever TRIRON N Series User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.