1. Introduction
The XSDTS k10-2 Smart Door Lock offers advanced keyless entry solutions for your home or apartment. Featuring biometric fingerprint recognition, Bluetooth connectivity via the Tuya Smart App, and traditional mechanical key access, this lock provides enhanced security and convenience. This manual will guide you through the installation, operation, and maintenance of your new smart door lock.
Image: XSDTS Smart Door Lock with Tuya and Bluetooth logos, demonstrating app control and fingerprint unlock capabilities.
2. Safety Information and FCC Compliance
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.
3. Packing List
Unpack the product package and check whether the following accessories are included:
Image: All components included in the XSDTS k10-2 Smart Door Lock package.
- Smart Lock (x1)
- Latch (x1)
- Strike Plate (x1)
- Keys (x2)
- Pin (x1)
- Screws (x6)
- Gusset Plate
- Installation Key
- Pull Bolt
- Lock Body Screw
- Gusset Box
- Lock Body
- Rear Lock
- Rear Lock Handle
- Front Lock
4. Setup and Installation
Follow these steps to install your smart door lock. Ensure you have all components from the packing list before starting.
4.1. Remove the Rear Lock Handle
- Remove the front panel.
- Use the Installation key to align with the hole and press down the spring.
- Remove the rear lock handle.
Image: Steps for removing the rear lock handle using the installation key.
4.2. Installation Steps
-
Step 1: Install the lock body and tighten screws.
Image: Installing the lock body into the door frame and securing it with screws.
-
Step 2: Install the front lock and pass the tail ruler through the square rod hole in the lock body.
Image: Attaching the front lock assembly and aligning the tail ruler.
-
Step 3: Install the rear lock and pass the tail ruler through the rear lock square bar hole. Then, tighten the pull screw.
Image: Attaching the rear lock assembly and securing it.
-
Step 4: Adjust and fasten the rear lock handle. Adjust the horizontal and vertical position of the reverse lock knob according to the horizontal and vertical state of the tail ruler, so that the reverse lock knob and the tail ruler are in a unified state. Align the gap in the rear lock handle with the gap in the lock body. Fasten the rear lock handle. After these steps, the installation is complete.
Image: Final adjustments and fastening of the rear lock handle.
Image: Visual summary of the installation process.
Image: Dimensions for the smart door lock, indicating compatibility with various door types.
5. Operating Instructions
5.1. Fingerprint Recognition
The lock features fast identification (0.1S) and can store up to 20 fingerprints (3 administrators, 17 regular users).
Image: Fingerprint sensor on the smart door knob.
5.2. Mechanical Knob Operation
- When the knob in the door is rotated to open vertically, the lock is in the normally open state. The fingerprint is continuously verified twice within 3 seconds, and the fingerprint unlock is verified once after the lock is closed.
- When the knob in the door is rotated to the horizontal position, it is reversed and locked.
- In anti-lock mode, only the administrator's fingerprint can be matched. The lock will automatically anti-lock after 5 seconds of unlocking.
Image: Visual guide for knob operation and lock states.
5.3. Tuya Smart App Operations
The Tuya Smart App is essential for fingerprint registration and managing your smart lock. If there is no registered user, any fingerprint can unlock the device initially.
- Download the Tuya Smart App from your mobile app market (e.g., App Store, Google Play) or scan the QR code below.
- Open your phone's Bluetooth and Location services, then open the Tuya Smart App.
- In the app, select to add a device manually or click "Add Device" to start connecting.
- Follow the on-screen prompts to connect the device. You may need to touch the device to wake it up for initial Bluetooth search. Once bound, direct connection is possible.
- Enter the homepage to add users and register fingerprints.
Image: QR code to download the Tuya Smart App.
Image: Screenshots of the Tuya Smart App interface for device connection and user management.
5.4. Definition of Lights and Buzzers
- Successful Identification: Green light on, 1 buzzer sound.
- Failed Identification: Red light flashes 3 times, 2 buzzer sounds.
- Charging: Red light on.
- Fully Charged: Green light on.
- Low Power Alarm: Red light flashes 5 times after opening the door.
5.5. Low Power Consumption State
- Not bound to Bluetooth: Device enters sleep state if no touch/knob twist for 15 seconds. Bluetooth cannot be searched. Touch fingerprint or press button to wake up and search for Bluetooth.
- Bound to Bluetooth: Device enters sleep state if no touch/knob twist for 4 seconds. No wake-up needed; mobile phone can directly initiate Bluetooth connection via Tuya Smart App.
5.6. Emergency Unlocking
- Unlock with a key: Use the provided mechanical keys.
- Emergency Power: If the battery is dead, you can power the door lock via the micro-USB port using your fingerprint to unlock.
Image: Methods for emergency unlocking, including mechanical key and USB power.
6. Maintenance
- Battery Management: The lock uses a dry battery. Monitor the low power alarm (red light flashes 5 times) and replace batteries or recharge via USB as needed. The remaining power allows for approximately 50 more unlocks after the alarm.
- Cleaning: Wipe the lock surface and fingerprint sensor with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Key Storage: Always keep at least one mechanical key outside the door in a secure location for emergency access.
7. Troubleshooting
- Lock enters 120-second lock state: This occurs after 5 consecutive recognition errors. The fingerprint will not respond, and an alarm will sound for 10 seconds. The lock can only be unlocked by Bluetooth or by waiting 120 seconds.
- Fingerprint not recognized immediately after registration: Some users have reported a slight delay (minutes to hours) before newly registered fingerprints work consistently. If this occurs, try again after a short period.
- Lock not responding: Check battery level. If low, recharge via micro-USB or use a mechanical key.
- Difficulty connecting via Bluetooth: Ensure your phone's Bluetooth and Location services are enabled. Try waking up the device by touching the fingerprint sensor or pressing a button.
7.1. Restore Factory Settings
To clear all data and reset the lock to factory settings:
- Method 1 (via Tuya App): In the Tuya Smart App, navigate to the device settings and select the option to "Disconnect and wipe data." Confirm the unbinding.
- Method 2 (Local Operation): Repeatedly rotate the knob 5 times within 5 seconds. The blue light of the fingerprint head will stay on, and the buzzer will sound for a long time. Within 10 seconds, touch any fingerprint to clear the data.
Image: Tuya Smart App interface for factory reset via app.
Image: Visual guide for local factory reset operation.
7.2. Aging Mode
To enter Aging Mode: Touch the fingerprint sensor for 10 seconds without entering a fingerprint. The white light will flash 2 times, and the buzzer will sound 3 times. Release your hand, and the device will enter aging mode. To exit, touch the fingerprint head again.
8. Specifications
| Function/Performance | Parameter | Remarks |
|---|---|---|
| Operating Voltage | 3.3-4.2V | Nominal Voltage 3.7V |
| Alarm Voltage | 3.5 ± 0.1V | (1) Low battery detection, local voice prompts (2) Unlock more than 50 times after low voltage alarm |
| Deep Sleep Power Consumption | ≤ 30uA | (1) Measurement method: Long standby power consumption credit |
| Static Power Consumption | ≤ 50 uA | |
| Dynamic Power Consumption | ≤ 200 mA | |
| Working Temperature | -25°C ~ +70°C | |
| Storage Temperature | -40°C ~ +85°C | Complies with GA374-2019 Standards |
| Humidity Requirements | < 93% RH | |
| ESD Protection | Contact +/- 8kV, air +/- 15kV | |
| Fingerprint Capacity | 20 | (3 administrators, 17 regular users) |
| Product Material | Aluminium Alloy + Stainless Steel | |
| Power Supply | DRY BATTERY (Ternary lithium battery) | |
| Applicable Door Thickness | 35-75mm | |
| Unlock Method | App, Bluetooth, Mechanical Keys, Card, Password, Fingerprint | |
| Suitable Door Type | Steel Door, Wooden Door, Brass Door, Stainless Steel Door | Domestic and foreign wooden door/office door/extremely narrow door/ecological door |
| Connectivity | Bluetooth | |
| Smart Home Platform | Tuya | |
| Protection Level | No Waterproof | |
| Special Features | Built-in Doorbell |
9. User Tips
- Initial Fingerprint Delay: Some users have noted that newly registered fingerprints might not work immediately. If this happens, wait a few minutes or hours and try again.
- USB-C Charging: The lock supports USB-C charging for convenience, which is a great feature for emergency power.
- Home Assistant Integration: While the lock works with Tuya, direct integration with Home Assistant may require additional setup or a Tuya gateway.
- Door Compatibility: The lock has been reported to work correctly on various door types, including metal doors.
10. Warranty and Support
For any issues, questions, or support needs, please contact the seller or manufacturer directly. Refer to the official product page or your purchase documentation for specific warranty details.
A detailed user manual in PDF format is available for download: View User Manual (PDF)