LYZRC L900 PRO SE

Contents

LYZRC L900 PRO SE GPS Drone User Manual

Model: L900 PRO SE | Brand: LYZRC

LYZRC L900 PRO SE drone with remote control and different color options

The LYZRC L900 PRO SE drone, showcasing its design, remote control, and available color variations.

1. Introduction and Safety Precautions

This manual provides essential instructions for the safe operation and maintenance of your LYZRC L900 PRO SE GPS Drone. Please read it thoroughly before your first flight.

Safety Precautions:

  • To ensure electromagnetic environment requirements of aviation radio stations, it is prohibited to use model remote controllers within a 5000M radius of an airport runway's center point. During periods when state departments issue radio control orders, the use of model remote controllers must be stopped.
  • Fly in warm, clear, windless weather. Avoid severe weather conditions such as overheating, strong wind, or rainstorms.
  • Choose an open indoor or outdoor area, keeping a safe distance from people, pets, empty overhead wires, and other obstacles. Ensure no other device uses the same frequency. Do not let the aircraft out of sight.
  • After the aircraft starts, do not contact high-speed rotating parts (gears, rotors, etc.) to avoid injury.
  • During and after use, the battery and motor will generate high temperatures. Avoid touching them to prevent scalding.
  • Do not look directly at the LED light beam to avoid affecting your eyes.

Warm Tip: Beginners are advised to practice flying at low altitude in an open, unmanned place for about 3 days to become familiar with flying before attempting high-altitude flights.

2. Setup

2.1 Flight Environment

Select an appropriate environment for flying your drone. Avoid areas with obstacles, crowds, or extreme weather conditions.

Diagrams illustrating suitable and unsuitable flight environments

Visual guide for selecting safe indoor and outdoor flight environments, avoiding obstacles and adverse weather.

  • Indoor: Spacious space away from obstacles, crowds, or pets is preferred.
  • Outdoor: Sunny, windy, and clear weather are preferred.
  • Keep the UAV in line of sight and away from obstacles, high-voltage cables, trees, and personnel during flight.
  • Do not fly in extreme environments such as heat, cold, strong wind, or heavy rain.

2.2 Remote Control Handle/Mobile Phone Rack Setup

Prepare your remote control for use by setting up the mobile phone rack.

  1. Lift the mobile phone rack in the middle of the remote controller upward.
  2. Stretch it upward to place your mobile phone securely.
  3. Pull the bottom handle of the remote control down from the middle position and rotate it into place.
Step-by-step diagrams showing how to lift and extend the mobile phone rack on the remote control

Visual instructions for deploying the mobile phone rack on the remote control.

2.3 Charging the Controller

Ensure your remote controller is fully charged before use.

  1. Insert the charging plug of the charging wire into the charging socket of the remote controller.
  2. Connect the USB charger plug to a computer or mobile phone charger.
  3. The charging indicator lights up during charging and turns off when fully charged.

Charging time is approximately 60 minutes. If the charge indicator does not change, the battery is already full.

Diagram showing how to charge the remote controller using a USB cable

Illustration of connecting the USB charging cable to the remote controller.

2.4 Charging Drone Lithium Battery

Charge the drone's battery for optimal flight performance.

  1. To remove the UAV battery, press on both sides as shown in the diagram and pull it upward.
  2. Plug the USB Android head into the battery and connect the USB charger to a computer or mobile phone charger.
  3. The Android headlight on the battery lights up during charging and the red light goes out when fully charged.

Charging time is approximately 90 minutes. If the Android headlight is not on when plugged in, no recharging is required.

Diagram illustrating how to remove the UAV battery

Instructions for removing the drone battery.

Diagram showing how to charge the drone's lithium battery

Instructions for charging the drone's lithium battery.

2.5 Pre-flight Environmental Requirements

Always check your flight environment before taking off.

  • Choose an open indoor or outdoor environment without rain, snow, or wind force exceeding Level 4.
  • Stay away from people, trees, electric wires, tall buildings, airports, and signal transmission towers.

3. Operating Instructions

3.1 Remote Control Function Key Description

Familiarize yourself with the remote control layout and functions.

Detailed diagram of the remote control with labels for all function keys and their names

Labeled diagram of the remote control, showing all buttons and their functions.

Note: When GPS needs to be turned off (e.g., for indoor flight), press and hold the GPS key for 3 seconds. The remote controller will emit a 'drop' sound, and the display will show 'GPS ON'. Then press the unlocking key to start the aircraft.

  • Aerial: Antenna.
  • Mobile phone rack: Holds your smartphone.
  • One key return: Initiates automatic return to home.
  • GPS switch: Toggles GPS mode.
  • Left joystick: Controls throttle and yaw.
  • Power switch: Turns the remote control on/off.
  • Liquid crystal display: Shows flight information.
  • Geomagnetic calibration: Initiates geomagnetic calibration.
  • Gyroscope calibration: Initiates gyroscope calibration.
  • Right control lever: Controls pitch and roll.
  • Unlock: Unlocks the motors for flight.
  • Power indicator: Shows battery level.
  • Headless indicator: Shows headless mode status.
  • GPS indicator: Shows GPS signal status.
  • Charging indicator: Shows charging status.
  • Velocity conversion: Adjusts flight speed.
  • Photo/video: Captures photos or starts/stops video recording.
  • Camera adjustment: Adjusts camera angle.
  • Headless mode: Toggles headless mode.
  • Long press left and right hand switch: Switches between left-handed and right-handed throttle modes.

3.2 Drone to Frequency

  1. Place the drone on horizontal ground and turn on its power, then turn on the remote control. Both lights will flash quickly.
  2. Push the left joystick of the remote control up and then pull it down. The drone's front and rear lights will change from consistent slow flash to alternating slow flash, indicating successful frequency pairing.
  3. After calibration, the headlight flashes slowly and then stays on, indicating it has entered the star search state.

3.3 Gyroscope Calibration

Calibrate the gyroscope for stable flight.

  1. Place the UAV in a horizontal position.
  2. Press and hold the "gyroscope calibration" button on the remote controller for 3 seconds.
  3. The UAV light will flash slowly, and the remote controller will emit a "Di" sound, indicating successful calibration.
Diagram showing the drone and remote control for gyroscope calibration

Visual guide for performing gyroscope calibration.

3.4 Geomagnetic Calibration

Perform geomagnetic calibration to prevent interference from other electronic devices.

  1. Press the remote control button for 3 seconds. The remote control will emit a "Di" sound, and the drone light will change from slow to fast flashing.
  2. Hold the UAV in your hand and slowly rotate it clockwise for 3 turns in the horizontal direction. The UAV's indicator light will change from flash to slow flash, and the remote controller will emit a "Di" sound.
  3. Then, rotate the nose slowly clockwise for 3 turns downward in the vertical direction. The red indicator light on the rear of the UAV will flash slowly and then become normally on, and the remote controller will emit a "Di" sound, indicating successful calibration.
Diagrams illustrating the steps for geomagnetic calibration (horizontal rotation, vertical rotation)

Diagrams showing the horizontal and vertical rotation steps for geomagnetic calibration.

3.5 Search for GPS Signals

After successful calibration, acquire GPS signals for stable outdoor flight.

  1. After calibration, the green indicator light in front of the UAV flashes slowly, and the red indicator light in the rear is always on.
  2. Place the UAV in a horizontal position for about 30 seconds. The green indicator light will change from slow flash to constant light, and the remote controller will emit a "Di" sound, indicating successful star search.
  3. Press and hold the "unlock button" of the remote controller to fly.

Special note: For calibration, place the UAV horizontally in a wide outdoor place. The green light in front of the aircraft flashes slowly, wait for about 30 seconds for the green light in front of the UAV fuselage to become normally on, and send out "Di" to indicate that the star Search is successful. Take the drone to an open area for calibration. New customers must calibrate once, as longitude and latitude vary by region.

3.6 UAV Unlock and Flight

Once GPS is acquired, unlock the drone for flight.

  1. When the drone has successfully positioned itself outdoors, press and hold the "unlock" button on the remote control.
  2. The four propellers will rotate at the same speed, indicating successful unlocking. The UAV is now ready to operate and fly normally.

3.7 Speed Gear Adjustment

Adjust the drone's speed during flight using the knob on the remote control.

  • The default take-off speed is slow gear.
  • Rotate the speed knob to the right: two 'drops' indicate second gear, three 'drops' indicate third gear (high-speed mode).
  • Rotate the speed knob to the left: indicates second gear and then first gear (low-speed).

3.8 Camera Angle Adjustment

Adjust the camera angle during UAV flight using the camera adjustment knob on the remote control.

  • Rotating the knob right decreases the camera angle.
  • Rotating the knob left increases the camera angle.
Diagram showing the camera angle adjustment knob on the remote control

Location of the camera angle adjustment knob on the remote control.

3.9 Headless Mode

Headless mode simplifies flight control by ignoring the drone's orientation.

  1. Place the UAV directly in front of the remote controller, with the nose facing forward. Calibrate and take off horizontally after frequency alignment.
  2. Press the headless mode button during flight. The remote controller will emit three 'drops', and the UAV's front indicator lights will flash slowly, indicating headless mode is active.
  3. To exit headless mode, press the headless mode button again.

In headless mode, the drone will move relative to the operator's orientation, regardless of the drone's actual front direction.

3.10 One-Press for Return

Use the one-press return function for automatic landing.

  1. When the drone is flying, press this function button on the remote control.
  2. The drone will automatically rise or fall to a height of 50 meters, return straight, and land at the take-off location.

Special suggestion: If the LED light in front of the drone flashes slowly during flight, it indicates insufficient power. If the drone's power is insufficient or it loses signal, it will automatically enter return mode and fly back along its original route.

Diagram showing the one-press return function button on the remote control and the drone's return path

Illustration of the one-press return button and the drone's automated return path.

3.11 Remote Controller Video/Picture Shooting Instructions

Capture aerial footage using the remote control.

  • Gently press the video key to take photos.
  • Long press the video key to record video.
Diagrams showing remote control joystick manipulations for drone movement

Visual guide for remote control joystick movements and their corresponding drone actions.

4. Maintenance

4.1 Blade Replacement

Proper blade replacement is crucial for stable flight.

  1. Ensure the replacement blade corresponds to its relative position on the drone. Fan blade A must be installed at position A, and fan blade B at position B. Incorrect replacement can lead to loss of control.
  2. When flying, fan blade A rotates clockwise, and fan blade B rotates counterclockwise.
Exploded view diagram of the drone showing main components like boom, electric machine, subject, fan blades, bottom power switch, and Wifi camera

Diagram illustrating drone components and blade positions (A and B).

4.2 Accessories Overview

The drone package includes various accessories for operation and maintenance.

Diagram showing various accessories included with the drone: upper cover, lower lid, paddle A/B, motor A/B, circuit board, battery, USB charging cable, remote control

Visual representation of the drone's accessories, including covers, blades, motors, circuit board, battery, charging cable, and remote control.

5. Troubleshooting

Refer to this guide for common issues and their resolutions.

Problems Causes Resolutions
Drone indicator is flashing while not responding 1. Unsuccessful Drone GPS search
2. Low power of Drone
1. Move the Drone to an empty place to perform search again
2. Charging the battery
Drone blades turn but can't fly 1. Low battery
2. Blade deformation
1. Charging the battery
2. Replacement of blade
The drone was badly shaken Blade deformation Replacement of blade
Can't keep the drone steady after fine-tuning 1. Blade deformation
2. Poor motor
1. Replacement of blade
2. Replacement of motor
After impact, uncontrolled flying of Drone when starting again Triaxial acceleration sensor overbalances due to impact Make the Drone standstill for 5-10 seconds

5.1 GPS Troubleshooting Videos

If you are experiencing issues with GPS signal acquisition, please refer to these official videos:

Video 1: L900 PRO SE GPS Troubleshooting Guide (Part 1)

Video 2: L900 PRO SE GPS Troubleshooting Guide (Part 2)

6. Specifications

Key technical specifications for the LYZRC L900 PRO SE drone:

Attribute Value
Drone ModelL900 PRO SE
GPSYes
Motor TypeBrushless Motor (1503 Brushless Motor)
Obstacle Avoidance TypesNo support
Remote Control DistanceAbout 1200M
Image Transmission DistanceAbout 300M-600M
Flight AltitudeAbout 120M
Drone Battery Capacity7.4V/2200mAh
Remote Control Battery3.7V/350mAh
Flight TimeAbout 18min
Video Maximum Resolution1080i/P (1920*1080)
Photo Resolution4K/6K/8K (set in APP)
FPS25fps
SD Card SupportedNo
Drone Weight220g
APP NameRX Drone
Aircraft Operating Frequency2.4 GHz
Camera Mount TypeFixed Camera Mount
FPV OperationYes
ConnectivityAPP Controller, Remote Control, WIFI
Sensor Size1/3.13 inches, 1/4 inches
Camera IntegrationCamera Included
Camera Features1080p HD Video Recording
Aerial PhotographyYes
Max Wind Speed Resistance< 10 KM/H
Max Takeoff Weight<1kg

7. User Tips

  • Beginner Practice: It is suggested that beginners practice flying at low altitude in an open and unmanned place for about 3 days to become familiar with flying before attempting high-altitude flights.
  • Propeller Check: Always verify that the letter/number on the propeller matches that on the drone arm before flight.
  • Battery Insulation: Ensure the insulation sticker on the drone's built-in battery has been removed before first use.
  • Camera Delay: The camera may experience some delay, which is common for learning to pilot.
  • Brazilian Users (Anatel): If importing to Brazil, be aware that the drone may be held by customs for Anatel analysis. You may need to open a commitment petition with Anatel to obtain approval. There are online resources (e.g., YouTube videos) that explain this process. Patience is required as the process can be slow.

8. Warranty and Support

For detailed instructions, warranty information, and further support, please refer to the official user manual PDF provided by LYZRC.

You can access the comprehensive user manual in PDF format here: LYZRC L900 PRO SE User Manual (PDF).

If you encounter issues not covered in this manual or require technical assistance, please contact LYZRC Official Store customer service.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.