1. Important Safety Information
WARNING! Failure to follow all warnings and safety instructions can cause your product to malfunction, resulting in an accident, severe personal injuries or even death to the rider.
- Read this manual thoroughly before using your suspension seatpost.
- Use only genuine SR SUNTOUR parts. The use of aftermarket replacement and spare parts voids the warranty of your seatpost and might cause failure. This could result in an accident, injury or even death.
- These instructions contain important information about the correct installation, service and maintenance of your suspension seatpost. Common mechanical knowledge may not be sufficient. Your suspension seatpost should only be installed, serviced and/or maintained by a trained and qualified bicycle mechanic with specialized tools.
- If you are going to use your seatpost in combination with a child seat, we strongly recommend using the SR SUNTOUR neoprene protection cover to prevent your child's finger from being accidentally pinched.
- Study all other owner's manuals provided with your bike and make yourself familiar with the components mounted to your bike.
Before Every Ride
WARNING! Avoid serious personal injury or even death. Do not ride the bicycle if any of the following criteria is not met! Correct any condition before you ride.
- Inspect your bicycle and suspension system including the handlebars, pedals, crank arms, seat post, saddle, etc. for any cracks, dents, bent or tarnished parts. Also search for any oil leaking out of your shocks. Be sure to check hidden areas on the underside of your bike. If any condition exists, consult a trained and qualified bicycle mechanic to determine the cause and make any necessary correction.
- Make sure your seatpost is fastened with the proper torque value according to the frame's seat-clamp's specifications. If you are using a quick release seat-clamp, make sure it is closed properly. An improperly tightened seat-clamp increases the risk that your seatpost might twist while riding. This implies the risk of an accident and fatal injuries. Please inspect by view and twisting of the saddle the seatpost for any unusual movement!
- Make sure the bolts which are securing the saddle are fastened with the proper torque value of 15-18Nm. A loose saddle could provoke an accident and/or fatal injuries.
2. Setup
Seatpost Installation
WARNING! We strongly recommend that your suspension seatpost is installed and set up by a qualified and trained bicycle mechanic. Improper installation can result in failure of the product, accident, injuries or even death. If you are going to install the suspension seatpost by your own, the installation should be inspected by a trained and qualified bicycle mechanic. The inspection needs to be confirmed by the dealer by signing this owner's manual on the last page along with the dealer's official stamp.
- Remove Old Seatpost: Remove your existing seatpost from the bicycle frame.
- Clean Seat Tube: Clean the inside of the seat tube to make sure no old grease or dirt remains inside. Ensure the seat-tube has no burrs which could scratch the new seatpost. If burrs are found, remove them so the seatpost can slide in smoothly.
- Install New Seatpost: Install your SR SUNTOUR NCX seatpost and insert it past the "MIN INSERT" mark. This mark must be completely below the top of the seat-tube. When correctly installed, no part of the "MIN INSERT" mark should be visible.
Saddle Installation
- Unscrew Fixing Bolts: Unscrew the two fixing bolts on both sides of the seatpost clamp using a 5mm Allen wrench. Unscrew them until the rail of the saddle can fit between the two halves of the clamp.
- Insert Saddle Rail: Install the saddle by inserting one rail into the clamp from one side.
- Secure Saddle: Press the saddle down firmly until you hear an audible "click" noise, indicating it is properly seated.
- Adjust Saddle Position: Adjust the saddle so that it is centered and its top surface is horizontal (recommended).
- Tighten Fixing Bolts: Tighten the fixing bolts using a 5mm Allen wrench. The suggested tightening torque is 15-18Nm.

Image: Close-up of the saddle clamp mechanism, indicating 7mm rail compatibility and a torque specification of 15-16Nm.
3. Operating
Preload Adjustment
WARNING! Proper preload adjustment is critical for the safe functioning of the SUSPENSION seatpost. Repeated bottoming- or topping-out under use can lead to a structural failure of the suspension seatpost, resulting in accidents and/or injuries.
- Check Adjustment: With somebody's support, sit on the bike with your hands and feet positioned normally. Have the supporter confirm that the seatpost is approximately 1/3 compressed.
- Adjust Compression: If the compression is not within the 1/3 range, remove the seatpost from the bicycle frame.
- Increase Preload: To increase the preload, use a 6mm Allen key and turn the adjuster clockwise.
- Decrease Preload: To decrease the preload, turn the adjuster counter-clockwise. Ensure to leave a minimum of 10mm of exposed threads visible at the bottom of the seatpost.
WARNING! Do not turn the adjuster bolt counter-clockwise beyond the initial position at delivery. In this original position, around 10mm of the seatpost thread should be visible.
Note: If the preload adjustment does not achieve the desired range, you may need an optional softer or harder spring from an authorized SR SUNTOUR dealer. If spring exchange still doesn't work, the seatpost might not be compatible with your bike/weight/use/terrain setup. Refer to the full PDF manual for more details on spring options (typically found on page 6).
4. Maintenance
Regular inspection and cleaning are crucial for the longevity and safe operation of your SR SUNTOUR NCX seatpost. Please refer to the "Before Every Ride" section for a detailed checklist of inspections to perform regularly. Keep the seatpost clean from dirt and debris, especially around the moving parts and seals.
5. Troubleshooting
If you experience any issues with your SR SUNTOUR NCX seatpost that cannot be resolved by following the setup or operating instructions, it is recommended to consult a trained and qualified bicycle mechanic. Do not attempt complex repairs yourself, as this may void your warranty and could lead to unsafe operation.
6. Specifications
| Feature | Specification |
|---|---|
| Type | Bicycle Seat Post |
| Material | Aluminum |
| Origin | TW (Origin) |
| Total Length | 350mm |
| Travel | 100mm |
| Available Diameters | 27.2mm, 28.6mm, 30.0mm, 30.4mm, 30.9mm, 31.6mm, 33.9mm |
| Weight (27.2mm model) | Approx. 798g |
| Saddle Rail Compatibility | 7mm Rails Only |
| Saddle Bolt Torque | 15-18Nm |
| Hign-concerned Chemical | None |

Image: Dimensional diagram showing 350mm total length, 100mm travel, and various diameter options.

Image: SR SUNTOUR NCX Suspension Seatpost (27.2mm) with a weight of 798g.
7. User Tips
- Spring Hardness: Many users inquire about the appropriate spring hardness for their body weight. The SR SUNTOUR NCX seatpost may come with different spring options (e.g., for riders under 65kg, up to 100kg, or even 120kg). If you are unsure which spring is suitable for your weight, please consult the seller or manufacturer's specifications for spring recommendations.
- Adapter Use: Ensure you select the correct diameter for your bike's seat tube. If using an adapter, confirm it is compatible and securely fitted to avoid movement or damage.
8. Warranty & Support
For warranty claims, technical support, or further assistance, please contact your original point of purchase or an authorized SR SUNTOUR dealer. Keep your proof of purchase for any warranty-related inquiries.
A detailed user manual in PDF format may be available for download. Please refer to the official product page or contact customer support for the link: SR SUNTOUR NCX User Manual (PDF)