EPever EPIPDB-COM

Contents

EPEVER EPIPDB-COM PWM Dual Battery Solar Controller

User Manual for Models EPIPDB-COM-10 and EPIPDB-COM-20

1. Introduction

This manual provides essential information for the installation, operation, and troubleshooting of your EPEVER EPIPDB-COM PWM Dual Battery Solar Controller. This controller is designed to manage solar charging for two independent battery banks, ensuring efficient power distribution and protection.

Front view of the EPEVER EPIPDB-COM PWM Dual Battery Solar Controller, showing controls and terminals.
Figure 1: EPEVER EPIPDB-COM PWM Dual Battery Solar Controller

2. Safety Precautions

WARNING:

  • Do not install the controller in humid, salt spray, corrosion, greasy, flammable, explosive, dust accumulative, or other severe environments.
  • Using a common-negative controller for common-negative systems, such as an RV system, is recommended. The controller may be damaged if a common-positive controller is used and the positive electrode is grounded in the common-negative system.

3. Product Overview

The EPIPDB-COM controller features a compact design with clear indicators and connection points for easy setup and monitoring. It includes a remote temperature sensor input and a remote meter connection for enhanced functionality.

Detailed view of the EPIPDB-COM controller's front panel, highlighting the remote temperature sensor, battery 1 and 2 connections, PV array connections, and remote meter connection points.
Figure 2: Controller Components and Connections

3.1. Key Features

  • PWM charging technology.
  • Dual battery charging capability.
  • Automatic 12V/24V system voltage detection.
  • Comprehensive electronic protection functions.
  • Optional remote temperature sensor and remote meter connection.

3.2. Protection Features

The controller incorporates multiple protection mechanisms to ensure safe and reliable operation:

Diagram showing protection features of the solar controller: over charging, short-circuit, reverse polarity, and reverse current to PV.
Figure 3: Controller Protection Features
  • Over charging protection
  • Short-circuit protection
  • Reverse polarity protection
  • Reverse current to PV protection

4. Installation and Wiring

Before installation, please watch the unboxing video to familiarize yourself with the product and its components.

Video 1: Unboxing and Physical Overview of 10A and 20A Models

4.1. Connection Sequence

Connect the components in the following order (1-6 as indicated in the diagram):

Connection diagram for the EPEVER EPIPDB-COM PWM Dual Battery Solar Controller, illustrating connections to solar panel and two batteries.
Figure 4: Connection Diagram
Icon Function
Battery 1 icon 1 Connect with battery #1.
Battery 2 icon 2 Connect with battery #2.
PV array icon PV Array Connect with the PV array.
Remote temp. sensor (Optional) Remotely measure the battery temperature to regulate the battery voltage.
Remote meter connection Connect with a remote meter.

Grounding: EPIPDB-COM series are common-negative controllers. Negative terminals of the PV array and batteries can be grounded simultaneously, or any negative terminal can be grounded. The grounding terminal on the controller shell must be grounded to shield electromagnetic interference and avoid electric shock.

5. Operation and Mode Setting

The controller uses three LEDs to indicate different specifications. To set a parameter, press the button for 5 seconds until the number flashes. Then, choose the desired number and release the button to save the setting.

5.1. Battery Type Setting (1st LED)

1st LED Battery Type
1 Sealed battery
2 Gel battery
3 Flooded battery

5.2. Charging Priority Setting (2nd LED)

Set the charging percentage for battery #1. The controller will automatically calculate the remaining percentage for battery #2.

2nd LED Battery #1 Charging Percentage Battery #2 Charging Percentage
00%100%
110%90%
220%80%
330%70%
440%60%
550%50%
660%40%
770%30%
880%20%
990% (pre-set)10%

Note: During normal charging, the controller charges batteries per the set percentage. If one battery is fully charged, more current will be diverted to the other battery. The controller automatically returns to the setting percentage when battery #1 is low voltage. If only one battery is detected, all charging current will go to that battery.

5.3. Charging Frequency Setting (3rd LED)

3rd LED PWM Charging Frequency
025Hz (pre-set)
150Hz
2100Hz

6. Troubleshooting

Refer to the table below for common issues indicated by the LED status and their corresponding solutions.

No. LED Status Troubleshooting
1 LED blinking Short circuit. Please check whether the PV and battery connection is correct.
2 LED slowly flashing Fully charged
3 LED ON In charging
4 LED frequent flashing No charging or any battery is detected.
5 LED OFF No battery or system over voltage.

7. Technical Specifications

Parameter EPIPDB-COM-10 EPIPDB-COM-20
Nominal system voltage12/24VDC Auto
Rated charge current10A20A
Battery TypeSealed; Gel; Flooded
Equalize charging voltageSealed: 14.6V; Gel: No; Flooded: 14.8V
Boost charging voltageSealed: 14.4V; Gel: 14.2V; Flooded: 14.6V
Float charging voltageSealed/Gel/Flooded: 13.8V
Maximum solar voltage30V (12V System); 55V (24V System)
Battery voltage range8 ~ 15V
Boost time120 minutes
Self-consumption4mA at night; 10mA at charging
Communication port8-PIN RJ-45
Temp. compensation-5mV/°C/2V
Terminals4mm²
Environment temperature-35°C ~ +55°C
Net weight250g

Note: The above parameters are measured for a 12V system. For a 24V system, please double the values where applicable.

8. Mechanical Drawing

The following diagram provides the mechanical dimensions of the EPIPDB-COM controller.

Top and bottom views of the EPIPDB-COM controller, showing the heat sink fins and a table of LED indicators for battery type and PWM frequency.
Figure 5: Mechanical Dimensions (mm/inches)

9. User Tips

  • Ensure you select the correct current rating (10A or 20A) for your specific solar and battery setup to prevent overloading and ensure optimal performance.
  • Regularly check all wiring connections for tightness and corrosion to maintain efficient power transfer and prevent potential issues.

10. Warranty and Support

For detailed warranty information, technical support, or further inquiries, please refer to the official EPEVER documentation or contact your vendor. A comprehensive user manual in PDF format is available for download: EPIPDB-COM User Manual (PDF).

Manufactured by HUIZHOU EPEVER TECHNOLOGY CO., LTD.

© 2023 EPEVER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.