1. Introduction
The EJEAS V6 PRO Helmet Intercom System is a performance-stable Bluetooth intercom designed for motorcycle riders. This system provides a maximum talking distance of 800 meters in outdoor environments, typically ranging from 300 to 800 meters. It also functions as a high-performance Bluetooth headset with a range of 10 meters.
Key features include automatic call reception for convenience and safety, a waterproof design, and HD-Voice technology, all built with a screw-less ultrasonic structure for durability. It is specifically designed to enhance safety and communication for motorcycle riders.
2. Product Overview
The EJEAS V6 PRO system consists of a main intercom unit (not included with this headset) and a wired microphone speaker headset. The main intercom unit features several buttons and interfaces for control and connectivity.
Main Intercom Unit Controls and Interfaces

Image: EJEAS V6 Pro Intercom Unit with Headset and Clip. This image shows the main intercom unit, the wired headset with microphone, and the mounting clip.
- MOTOR/A button: Used for power on/off and pairing with 'A' device.
- B button: Used for pairing with 'B' device.
- C button: Used for pairing with 'C' device.
- D button: Used for pairing with 'D' device.
- E button: Used for pairing with 'E' device.
- Phone button: Controls phone calls (answer, refuse, redial) and music playback.
- Volume +: Increases volume and selects next music track.
- Volume -: Decreases volume and selects previous music track.
- Antenna: For wireless communication.
- Earphone interface / USB charger interface: Connects the headset and is used for charging the intercom unit.
Headset Components

Image: EJEAS Vnetphone Headset with Microphone and 3.5mm Jack. This image displays the two speaker pads, the flexible microphone, and the 3.5mm audio jack connector.
- Speakers: Two flat speakers designed to fit inside a helmet.
- Microphone: A flexible boom microphone with a foam cover for clear voice capture.
- 3.5mm Audio Jack: Connects the headset to the main intercom unit.
3. Setup and Installation
Proper installation ensures optimal performance and comfort. Follow these steps to install the headset and mounting clip on your helmet.
3.1 Mounting the Intercom Clip
- Identify a suitable location on the left side of your helmet, near the bottom edge, where the intercom unit can be easily accessed.
- Secure the mounting clip to the helmet. The clip can be attached by sliding it onto the helmet's edge or by using screws if your helmet design allows for it. Ensure it is firmly in place.

Image: EJEAS Vnetphone Intercom Mounting Clip. This shows the plastic clip with screw holes for secure attachment.

Image: Intercom Mounting Clip Installed on Helmet. The clip is shown securely attached to the side of a motorcycle helmet.
3.2 Installing the Headset Speakers and Microphone
- Open the helmet's inner lining to access the ear pockets.
- Place one speaker into each ear pocket, ensuring they are positioned comfortably over your ears. Use the provided adhesive pads if necessary to secure them.
- Route the microphone towards the front of the helmet, positioning it near your mouth for optimal voice pickup. Ensure the cable is tucked away neatly within the helmet lining.
- Connect the 3.5mm audio jack of the headset to the corresponding earphone interface on the main intercom unit. Ensure the jack is fully inserted to prevent water ingress, especially in rainy conditions.

Image: Headset Speakers Installed Inside Helmet. This image shows the flat speakers and wiring neatly placed within the helmet's padding.
3.3 Compatibility Note
This headset is designed for the EJEAS V6 Pro and Vnetphone V4 intercom units. Please note that it is NOT compatible with the EJEAS V6 Pro+ model due to different clip interfaces and connection types.

Image: EJEAS V6 Pro vs V6 Pro+ Compatibility Diagram. This diagram visually distinguishes between the compatible V6 Pro and incompatible V6 Pro+ models based on their clip interface and mounting clip design.
4. Operation
4.1 Power On/Off
- Power On: Long press the MOTOR button for approximately 2 seconds until the main device light flashes.
- Power Off: Press the Power off button (MOTOR button).
4.2 Connecting with Phone (GPS/MP3)
- Long press the Phone button for 5 seconds until the red and blue lights flash alternately.
- On your phone, enable Bluetooth and search for the V6 device.
- Select V6 to connect. Once successfully paired, the intercom's blue light will flash.
- Note: If your GPS/MP3 device supports Bluetooth, the pairing process is the same as with a phone.
4.3 Last Number Redial
After connecting to your phone, long press the Phone button for 3 seconds. The device will automatically dial the last outgoing call number from your phone.
4.4 Receiving and Refusing Calls
- Receiving a Call: When a call comes in, if no operation is performed for 5 seconds, the device will automatically answer the call.
- Refusing a Call: When a call comes in, press the Phone button to end the call.
4.5 Music Playback
- Play/Suspend Music: Short press the Phone button. This function is 95% compatible with cellphone music players.
- Choose Music (Previous/Next):
- Previous Music: Long press Volume - for 2 seconds.
- Next Music: Long press Volume + for 2 seconds.
4.6 Volume Control
- Add Volume: Press Volume + button.
- Down Volume: Press Volume - button.
4.7 Charging Tip
When the intercom unit is charging, the red indicator light will be continuously on. Once fully charged, the red light will turn off.
4.8 Clear Pairing (Restore Factory Settings)
To clear all pairing records and restore factory settings, press the Phone button and the B button simultaneously. The indicator light will flash red three times and then blue once.
4.9 Intercom Operation
The V6 system supports up to six riders, with two riders able to talk simultaneously. One main device can be paired with up to five sub-devices (A, B, C, D, E). The main device can select one sub-device to communicate with at a time.

Image: EJEAS V6 Pro Intercom Pairing Diagram. This diagram illustrates how a main intercom unit can connect to multiple sub-units (A, B, C, D, E) for group communication.
Pairing with Sub-Devices (A, B, C, D, E)
- Pairing with 'A' Device: Long press the MOTOR buttons on both the main device and the 'A' device for about 5 seconds simultaneously. Both devices' red and blue lights will flash. Once they find each other, one will automatically initiate a pairing connection, and the blue light will flash quickly. After a successful connection, the blue lights will flash slowly simultaneously, indicating normal communication. To pair the next sub-device, first press the MOTOR button to disconnect.
- Pairing with 'B' Device: Long press the B buttons on both the main device and the 'B' device for about 5 seconds simultaneously. Both devices' red and blue lights will flash. After they find each other, one will automatically initiate a pairing connection, and the blue light will flash quickly. After a successful connection, the blue lights will flash slowly simultaneously, indicating normal communication. To pair the next sub-device, first press the B button to disconnect.
- Pairing with 'C', 'D', and 'E' Devices: The pairing method for 'C', 'D', and 'E' devices is the same as above, using their respective C, D, and E buttons on the main device.
Note: Once paired, you do not need to pair again for subsequent uses. Simply click the corresponding MOTOR/B/C/D/E button on the main device to connect and talk.
4.10 EUC Remote Controller (Optional)
If you have an optional EUC Remote Controller, refer to the following for button functions and pairing instructions.

Image: EUC Remote Controller Button Layout. This diagram shows the various buttons on the EUC remote controller, including Button FM, Button C, Button B, Button A, Phone Button, Volume +, and Volume -.
EUC Remote Controller Button Functions
| Button | Action | Function |
|---|---|---|
| Volume - | Short press | Volume - |
| Long press | Previous song when music is playing | |
| Double click | None | |
| Phone Button | Short press | Answer call / On call, hang up / Music play/pause / Connect last connected phone |
| Long press | Call rejection / Voice assistant | |
| Double click | Last number redial | |
| Volume + | Short press | Volume + |
| Long press | Next song when music is playing | |
| Double click | None | |
| Button A | Short press | Intercom A pairing |
| Long press | Disconnecting the intercom | |
| Double click | Intercom D pairing | |
| Button B | Short press | Intercom B pairing |
| Long press | Disconnecting the intercom | |
| Double click | Intercom E pairing | |
| Button C | Short press | Intercom C pairing |
| Long press | Disconnecting the intercom | |
| Volume - + Button FM | Super Long Press | Clear EUC handle pairing records |
EUC Pairing Instructions
- Clear EUC Pairing Record: Long press both the <Button FM> and <Volume -> buttons on the EUC for 5 seconds. The red and blue lights will be on simultaneously.
- Enter Handle Pairing Mode: Long press both the <Phone Button> and <Button E> on the EUC for 5 seconds. The red and blue lights will flash alternately and quickly.
- Connect: Click any button on the EUC.
Pairing Successfully: You will hear a "Du" sound. If the EUC cannot be successfully paired within 2 minutes, it will automatically exit the pairing mode.
4.11 Restore Default Settings (Intercom Unit)
Press and hold both the <B button> and <Phone button> for about 2 seconds. The red light will flash 3 times quickly to delete the pairing record, and then the intercom will automatically power on again. You will hear "Di, Di, Di" indicating the reset.
5. Mobile App (SafeRiding)
The SafeRiding mobile application provides additional features for your intercom system, including intercom group management, music control, FM control, switching on/off, authenticity checks, and other functions.

Image: SafeRiding Mobile App Setup Diagram. This diagram illustrates the steps to download, install, and connect the SafeRiding app to the intercom unit for enhanced control.
- Download and Install: Download and install the SafeRiding mobile APP for the first time. QR codes for iOS and Android are typically provided in the product packaging or official website.
- Enter Pairing Mode: Press and hold the <Phone Button> on the intercom unit for approximately 5 seconds until the red and blue lights flash alternately and quickly.
- Connect via App: Open the SafeRiding APP. Click on the Bluetooth icon in the top right corner. The interface will show the name of the intercom device. Select the intercom device to be connected and click to connect.
Note: For iOS systems, you may need to enter the phone's Bluetooth settings (Settings -> Bluetooth) to connect the audio Bluetooth.
For subsequent uses, simply open the APP, click the Bluetooth icon, and select your Intercom from the paired devices list to connect.
6. Precautions for Use
- Installation: Ensure correct installation. When riding in rainy conditions, make sure the headphone jack is fully inserted into the device to prevent water ingress.
- Battery Life: To ensure optimal battery life, please use the standard charger provided or recommended by the manufacturer.
- Riding Safety: It is not recommended to listen to music while riding, as it may distract you.
- Device Operation: Avoid manually operating the device buttons while riding to maintain focus on safety.
- Communication Distance: For best communication distance, it is recommended to use the device in open areas.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | EJEAS |
| Model Name | EJEAS V6 Pro Microphone (Headset) |
| Item Type | Helmet Headset |
| Connection Mode | Wire (3.5mm jack) |
| Special Features | Noise Reduction |
| Applicable Helmet Type | MODULAR, MOTOCROSS, Open face, Full Face, Flip Up Helmet |
| Battery Included | Yes (refers to the main intercom unit, not the passive headset) |
| High-concerned Chemical | None |
| Support Intercom (Headset) | No (This headset is an accessory for an intercom unit, not an intercom unit itself) |
| Maximum Intercom Distance | <500m (Capability of the connected intercom unit) |
| Maximum Number of Speakers | 2 (Capability of the connected intercom unit) |
| Item Weight | 50g |
| Item Dimensions (L x W x H) | 7.8cm x 3.2cm x 2cm |
| External Testing Certification | CE |
| Certification | CE |
| Origin | Mainland China |
8. User Tips
- Easy Installation: Users report the headset is very easy to install and assemble within the helmet.
- Check Connections: Before use, carefully check that both headset speakers are working and that the 3.5mm plug is fully and securely connected to the intercom unit. Issues can sometimes arise from loose connections.
- Value for Money: Many users find this product offers great value, especially for maintaining communication while riding.
- No Charging Cable for Headset: The headset itself is passive and does not require a charging cable; power is supplied by the intercom unit.
9. Frequently Asked Questions (FAQ)
- Q: Is this headset used for communication between rider and passenger?
- A: Yes, when connected to a compatible EJEAS V6 Pro or Vnetphone V4 intercom unit, this headset allows for communication between riders or between a rider and passenger, depending on the intercom unit's capabilities.
- Q: Is this headset compatible with the EJEAS V6 Pro+?
- A: No, this headset is specifically designed for the EJEAS V6 Pro and Vnetphone V4 intercoms and is not compatible with the EJEAS V6 Pro+ due to differences in the connection interface.
- Q: How does the mini jack connection work?
- A: The headset connects to the main intercom unit via a standard 3.5mm audio jack. Simply plug the jack into the designated earphone interface on your compatible intercom unit.
- Q: Will this headset work with my Lexin LX-R6 intercom?
- A: This headset uses a standard 3.5mm jack. If your Lexin LX-R6 intercom unit has a compatible 3.5mm earphone interface, it may work. However, we cannot guarantee full compatibility with third-party intercoms. Please check your intercom's specifications for 3.5mm headset support.
10. Warranty and Support
For warranty information, technical support, or further assistance, please refer to the official EJEAS website or contact your retailer. A detailed user manual in PDF format may also be available for download from the manufacturer's website for comprehensive information.
You can view the user manual PDF here.