QIACHIP KR2201GS-4

Contents

QIACHIP RF 433MHz Wireless Smart Switch User Manual

Models: KR2201G, KR2201GS

Safety Warnings

  • This device is for indoor use only.
  • This device should not be exposed to dripping or any dangerous sources.
  • This device should only be installed by adults.
  • Do not install near any heat sources.
  • Do not use this device with dimmers.
  • Do not use this device in a fully enclosed fixture.
  • Pay attention to electricity and do not use it in humid places.
  • If the unit is heavier than the replacement unit, it may reduce the stability of some fixtures and affect the contacts.

Product Overview

The QIACHIP RF 433MHz Wireless Smart Switch is designed to provide convenient control over lighting and other home appliances. It can be operated via a wireless remote control or an external wall switch, offering flexible control options for various scenarios.

Product overview showing the smart switch module, a remote control, and wall panels, with voltage and frequency details.
Figure 1: QIACHIP Smart Switch System Overview

The compact design allows for easy integration into various wiring boxes, making it suitable for adding new wall switches, replacing hard-to-reach switches, or implementing multi-way switching solutions.

Features of the smart switch, highlighting its small and compact size suitable for various mounting boxes, and excellent heat dissipation. Notes that it only works with mechanical rocker switches, not electronic ones, and does not support 2.4G network.
Figure 2: Compact Design and Heat Dissipation

Specifications

FeatureSpecification
Brand NameQIACHIP
Model NumberKR2201GS-4 (also KR2201G, KR2201GS)
Working VoltageAC 90V-250V 50/60Hz
Max Load10A
Max Load Power (AC220V)2200W
Incandescent Lamp Load500W
Capacitive Load200W
Energy-saving Lamp Load300W
Frequency433 MHz / 433.92MHz
Wireless CommunicationRF, Wire Control
Remote DistanceOpen space is more than 50 meters
Receiving Sensitivity97dbm
Modulation ModeASK
Matching ModeIntelligent Learning code 1527
Working Temperature-30 ~ +80 °C
CertificationCE, FCC, RoHS
Support APPNo

Installation and Setup

Before installation, ensure the power supply is disconnected to prevent electric shock. This device is designed for easy integration into standard electrical boxes.

Wiring Diagrams

The QIACHIP Smart Switch supports various wiring configurations. Refer to the diagrams below for your specific model and control method.

Detailed wiring diagram for the smart switch between power and lights, including dimensions (40mm) and showing compact receiver fitting into rose/canopy, junction box, and switch box.
Figure 3: General Wiring Diagram and Dimensions

KR2201G Wiring (Remote Control Only)

Remote control unit with A, B, C buttons and a keychain.
Figure 4: Remote Control Unit
Diagram illustrating two-way control support with the smart switch and a light bulb.
Figure 5: KR2201G Wiring Diagram (Remote Control Only)

For the KR2201G model, which is controlled exclusively by remote control, connect the Live (L) and Neutral (N) input wires to the AC 90-250V power supply. Connect the Live (L) and Neutral (N) output wires to your light or appliance. This model does not support external wall switches.

KR2201GS Wiring (Remote Control & External Switch)

Wall panel switch.
Figure 6: Wall Panel Switch
Installation example of the smart switch module into a ceiling light fixture.
Figure 7: KR2201GS Wiring Diagram (Remote Control Wiring Method)

For the KR2201GS model, which supports both remote and external switch control, the wiring is similar to KR2201G for remote control functionality. The Live (L) and Neutral (N) input wires connect to AC 90-250V. The Live (L) and Neutral (N) output wires connect to the light. The 'S' terminal is for the external switch connection.

Installation example of the smart switch module into a wall switch box.
Figure 8: KR2201GS Wiring Diagram (Simultaneous Use of Remote Control and External Switch)

When using an external switch with the KR2201GS, connect one terminal of the external switch to the 'S' input of the smart switch and the other terminal to the Live (L) input. This allows for dual control.

Diagram showing how to use an external switch for pairing with the QIACHIP Smart Switch.
Figure 9: External Switch for Pairing

Installation Examples

Installation example of the smart switch module into a ceiling light fixture.
Figure 10: Installation into a Ceiling Light Fixture
Installation example of the smart switch module into a wall switch box.
Figure 11: Installation into a Wall Switch Box

Video Guide: Wiring and Pairing

Video 1: Detailed demonstration of wiring the QIACHIP Smart Switch and pairing it with both remote controls and wall panel switches.

Video Transcript Highlights:

  • The blue wire outputs live wire and the black wire outputs neutral wire.
  • The green line connects to the switch outside, while the white and red lines are the input zero line and fire line, respectively.
  • The original switch is connected to the green wire and the input fire wire.
  • To clear codes: Press the controller eight times in a row.
  • To pair Toggle mode: After the indicator light stops blinking, press twice in a row. The indicator light is on. Press the switch panel to turn it off.
  • To pair Latching mode: Press the controller three times in a row. The indicator light is on, press A first, and the indicator light will blink. Then press B again.

Operating Instructions

Wireless Remote Control Function (Applicable Models: KR2201G/KR2201GS)

Diagram of the QIACHIP Smart Switch with the Smart Circuit Breaker Pairing Button highlighted.
Figure 12: Smart Circuit Breaker Pairing Button

The Smart Circuit Breaker Pairing Button is located on the smart switch module.

1. Toggle Mode Setting Description

In Toggle mode, one press turns the device ON, and another press turns it OFF.

  1. Press the setting button on the "Smart switch" twice. The red indicator light will flash and then light up.
  2. Press the button on the remote control that needs to be paired.
  3. When the red indicator light flashes and goes out, the toggle mode setting is successful.

2. Latch Mode Setting Description

In Latch mode, one button turns the device ON, and a different button turns it OFF.

  1. Press the code button on the "Smart switch" 3 times. The red indicator light will flash and then light up.
  2. Press the function key that is set to turn on (e.g., button ON/A).
  3. Then press to turn off the desired function key (e.g., button OFF/B).
  4. The red indicator light will flash to confirm that the latch mode is successfully set.

3. Push Button Mode Setting Description

In Push Button mode, the device is ON only while the button is pressed.

  1. Press the code Setting button on the "Smart switch" 4 times.
  2. The red indicator light flashes on the remote control. When the red indicator light flashes it goes out, the push button mode is set successfully.

External Switch Pairing Instructions (Applicable Models: KR2201GS)

External switch support type: Toggle Switch

Diagram showing how to use an external switch for pairing with the QIACHIP Smart Switch.
Figure 13: External Switch Pairing

1. Toggle Mode Setting Description (External Switch)

  1. Connect the power and the light to the KR2201GS.
  2. Press the external switch five times in a row. The light will flash three times and stay on, indicating pairing mode.
  3. Within 5 seconds, press the corresponding button on the remote control to pair.
  4. The light will turn off when pairing is complete. (If no pairing within 5 seconds, the load will remain connected and exit pairing mode.)

2. Latch Mode Setting Description (External Switch)

  1. Connect the power and the light to the KR2201GS.
  2. Press the external switch 6 times. The light will flash 3 times and then stay on, indicating that it has entered the pairing mode.
  3. Within 5 seconds, press the button on the remote control that you want to set as the "ON" button (e.g., Button A). The load will disconnect and reconnect 3 times, and then stay connected.
  4. Next, press the button on the remote control that you want to set as the "OFF" button (e.g., Button B). The load will disconnect and reconnect 3 times, and then turn off.
  5. If no pairing occurs within 5 seconds, the load will remain connected and exit the pairing mode.

Reset Settings

1. Reset via Smart Switch Button

  1. Press the controller eight times in a row to perform code clearing operation.
  2. After the indicator light stops blinking, all paired remote control data is erased.

2. Reset via External Switch (Applicable Models: KR2201GS)

  1. Connect the KR2201GS to the power supply and lamp.
  2. Press the external switch 8 times in a row.
  3. The light will flash 3 times before turning off. Reset is done. All remote control data is erased.

User Tips

  • The remote control typically uses a CR2032 button battery. Note that the battery is usually not included with the product.
  • Some remote control PCBs may have more internal switches than visible buttons. These unused switches might be programmable for additional functions.

Troubleshooting

  • Device not responding: Ensure all wiring connections are secure and correct according to the diagrams. Verify the power supply is active.
  • Remote control not working: Check the remote control battery (CR2032). Ensure the remote is paired correctly with the receiver module. Try re-pairing if necessary.
  • Intermittent operation or loss of pairing: In rare cases, strong electrical interference or power fluctuations (e.g., during heavy storms) might cause the device to lose its programming. If this occurs, perform a reset and re-pair the remote controls/switches.
  • External switch not working (KR2201GS only): Ensure the external switch is a mechanical toggle type and wired correctly to the 'S' and 'L' terminals. Electronic rocker switches are not supported.

Maintenance

  • Keep the device clean and free from dust. Use a dry, soft cloth for cleaning.
  • Avoid exposing the device to extreme temperatures, direct sunlight, or high humidity.
  • Regularly check wiring connections for any signs of wear or damage.
  • Replace the remote control battery (CR2032) as needed. Battery life can extend for several years under normal use.

Warranty and Support

For detailed warranty information or technical support, please refer to the official QIACHIP website or contact your retailer. A user manual in PDF format is also available for download from the manufacturer's website: User manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.