HIKVISION DS-KIS603-P(C)

Contents

HIKVISION DS-KIS603-P(C) POE Video Intercom Kit User Manual

Models: DS-KV6113-WPE1(C) Door Station & DS-KH6320-WTE1 Indoor Station

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of your HIKVISION DS-KIS603-P(C) POE Video Intercom Kit. This kit includes the DS-KV6113-WPE1(C) Villa Door Station and the DS-KH6320-WTE1 Network Indoor Station, designed to provide secure and convenient communication for your home or office.

HIKVISION DS-KIS603-P(C) Video Intercom Kit packaging
Figure 1.1: HIKVISION DS-KIS603-P(C) Video Intercom Kit Packaging

2. Package Contents

Before installation, please verify that all items are present and in good condition.

Contents of the HIKVISION DS-KIS603-P(C) Video Intercom Kit
Figure 2.1: Kit Contents - DS-KV6113-WPE1(C) Door Station, DS-KH6320-WTE1 Indoor Station, and Power Supplies.
  • DS-KV6113-WPE1(C) Villa Door Station (x1)
  • DS-KH6320-WTE1 Network Indoor Station (x1)
  • Power Supply (x2)
  • Mounting Template
  • Mounting Plate
  • Screws and other installation accessories

3. Setup and Installation

Ensure all related equipment is powered off before beginning installation. You will need a drill (2.8-6mm) and a gradienter.

3.1. DS-KV6113-WPE1(C) Villa Door Station

3.1.1. Appearance and Terminals

Front view of HIKVISION DS-KV6113-WPE1(C) Door Station
Figure 3.1: Front View of Door Station
Side view of HIKVISION DS-KV6113-WPE1(C) Door Station
Figure 3.2: Side View of Door Station
Back view of HIKVISION DS-KV6113-WPE1(C) Door Station with wiring terminals
Figure 3.3: Back View and Wiring Terminals of Door Station

Indicator Description:

  • Unlock: Green
  • Call: Orange

Terminals:

  • NC: Door Lock Relay Output (NC)
  • NO: Door Lock Relay Output (NO)
  • COM: Common Interface
  • AIN1: For the access of Door Contact
  • AIN3: For the access of Exit Button
  • AIN2 & AIN4: Reserved
  • 485-: RS-485 Interface (Reserved)
  • 485+: RS-485 Interface (Reserved)
  • 12 VDC IN: Power Supply Input
  • GND: Grounding

3.1.2. Mounting the Door Station

The door station supports surface mounting. You can choose to install it with or without a protective shield.

Surface Mounting without Protective Shield:

  1. Stick the mounting template on the wall. Drill screw holes according to the template. Remove the template.
  2. Secure the mounting plate on the wall with 4 supplied screws.
  3. Install the villa door station to the mounting plate. Fix the device on the mounting plate with the set screw.

Note: Apply silicone sealant around the cable wiring area to prevent water from entering.

Surface Mounting with Protective Shield:

  1. Stick the mounting template on the wall. Drill the screw holes according to the template. Remove the template.
  2. Align the protective shield with the mounting template.
  3. Secure the mounting plate and protective shield on the wall with 4 supplied screws.
  4. Install the villa door station to the mounting plate. Fix the device on the mounting plate with the set screw.

Note: If installing outdoors, it is advised to install the device with a protective shield.

The recommended height for the camera (distance between camera and ground) is 1.4 m to 1.6 m.

3.2. DS-KH6320-WTE1 Network Indoor Station

3.2.1. Appearance and Terminals

HIKVISION DS-KH6320-WTE1 Indoor Station screen showing time and menu icons
Figure 3.4: Indoor Station Screen Interface

The indoor station features a 7-inch touch screen. The rear panel contains 20 pins for various connections: 2 RS-485 pins, 5 reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.

3.2.2. Mounting the Indoor Station

The indoor station supports wall mounting. The wall mounting plate and a junction box are required. The junction box should be 75 mm (width) x 75 mm (length) x 50 mm (depth).

Wall Mounting with Junction Box:

  1. Chisel a hole in the wall (76 mm width x 76 mm length x 50 mm depth).
  2. Insert the junction box into the chiseled hole.
  3. Fix the wall mounting plate to the junction box with 2 screws.
  4. Hook the indoor station to the wall mounting plate by inserting the plate hooks into the slots on the rear panel. The lock catch will engage automatically.

Wall Mounting without Junction Box:

  1. Insert 2 expansion tubes into the wall.
  2. Fix the wall mounting plate to the wall with 2 screws.
  3. Hook the indoor station to the wall mounting plate by inserting the plate hooks into the slots on the rear panel. The lock catch will engage automatically.

3.3. Wiring Diagrams

Proper wiring is crucial for the system's functionality. Refer to the diagrams below for connections.

3.3.1. General Terminal Description

General terminal wiring diagram for HIKVISION door station
Figure 3.5: Door Station General Terminal Wiring

Note: RS-485 terminal is not supported for this model.

3.3.2. Door Lock Wiring

This diagram illustrates how to connect a door lock to the door station.

Note: Terminal NC/COM is set as default for accessing magnetic lock/electric bolt; terminal NO/COM is set as default for accessing electric strike.

3.3.3. Door Contact Wiring

This diagram illustrates how to connect a door contact sensor.

3.3.4. Exit Button Wiring

This diagram illustrates how to connect an exit button.

4. Operation

4.1. Device Activation via Web

You must activate the device by setting a strong password before use.

  1. Power on the device and connect it to the network.
  2. Enter the device's IP address (default: 192.0.0.65) into a web browser.
  3. Create and confirm a password in the activation page.
  4. Click OK to activate the device.

Note: The computer and the device should be on the same subnet. Basic operations and remote configuration cannot be performed until the device is activated.

4.2. Accessing the Device by Web Browsers

  1. In the browser address bar, enter the device's IP address and press Enter.
  2. Enter the user name (default: admin) and password, then click Login.

4.3. Communication with Indoor Station

  1. On the indoor station, navigate to Settings > Intercom Press Button to Call.
  2. Set the call number for each button.
  3. Optionally, check Call Management Center to set the button calling center.

Note: If both Call Management Center and a call number are set, the Call Management Center has higher priority.

4.4. Issue Card (for Access Control)

  1. On the indoor station, navigate to Settings > Access Control and Elevator Control.
  2. Click Issue Card. Present the card on the card reading area of the door station.
  3. A confirmation window will appear on the settings page when issuing is complete.

Note: Up to 10,000 cards can be managed. A voice prompt will indicate if the card limit is exceeded.

4.5. Unlock Door

After issuing cards, you can unlock the door by presenting the issued cards to the door station's card reading area.

4.6. Mobile App Control (Hik-Connect)

The Hik-Connect app allows you to receive calls, open the door, and view live footage remotely from your smartphone.

Screenshots of the Hik-Connect mobile app interface for the intercom system
Figure 4.1: Hik-Connect Mobile App Interface

Key features demonstrated in the video:

  • Receiving Calls: When a visitor presses the doorbell, both the indoor station and your mobile phone (via Hik-Connect app) will receive the call.
  • Two-Way Audio/Video: Communicate with visitors through the indoor station or the app.
  • Remote Unlock: Unlock the door directly from the indoor station or the Hik-Connect app.
  • Motion Detection Recording: The system can record video clips when motion is detected at the door station.
  • Call Recording: Video of calls made from the door station can be recorded and reviewed.
Video 4.1: Demonstration of HIKVISION Intercom System features including call, motion detection recording, and door unlock via indoor station and mobile app.

5. Maintenance

To ensure optimal performance and longevity of your HIKVISION Video Intercom Kit, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the surfaces of both the door station and indoor station. Avoid abrasive cleaners, solvents, or aerosol sprays that could damage the finish or internal components.
  • Environmental Conditions: Ensure the devices are operated within their specified temperature and humidity ranges. Protect the outdoor unit from direct exposure to extreme weather conditions where possible, even though it is waterproof.
  • Firmware Updates: Periodically check the HIKVISION official website or Hik-Connect app for available firmware updates to ensure your system has the latest features and security enhancements.
  • Cable Management: Regularly inspect all cables for any signs of wear or damage. Ensure connections are secure.

6. Troubleshooting

If you encounter issues with your intercom system, try the following steps:

  • No Power: Check all power connections and ensure the power adapter is securely plugged in. If using PoE, verify the PoE switch is functioning correctly and providing power.
  • No Video/Audio: Check network cable connections. Ensure both the door station and indoor station are properly connected to the network. Verify volume settings on the indoor station.
  • Door Unlock Failure: Check the wiring to the door lock. Ensure the access card is properly registered.
  • Network Connectivity Issues: Verify the IP address settings and ensure the device is on the same subnet as your network. Restart your router/switch and the intercom devices.

7. Specifications

7.1. DS-KV6113-WPE1(C) Villa Door Station

FeatureSpecification
Size138mm*65mm*27mm
DoorbellYes
MaterialPlastic
PowerIEEE802.3af, standard PoE 12 VDC
Sensor Size(Inch)1/3
IP Camera InterfaceNo
Access ControlInductive Card
WaterproofYes
Smart Home InterfaceYes
InstallationSurface
Communication InterfaceWired
TypeIntercom System
Viewing Angle (°)H:131° V: 78°
Answering ModeHands-free
Camera Sensor typeCMOS
Connection MethodWired
OriginMainland China
Smart home platformNone
CertificationCE
Power (W)10 W
TechnologyDIGITAL

7.2. DS-KH6320-WTE1 Network Indoor Station

CategoryFeatureSpecification
System ParametersOperation SystemLinux
ROM32 MB
RAM128 MB
Display ParametersScreen Size7-inch
Operation MethodCapacitive touch screen
TypeColorful TFT
Resolution1024 x 600
Audio ParametersAudio Input1 built-in omnidirectional microphone
Audio Output1 built-in loudspeaker
Audio QualityNoise suppression and echo cancellation
Volume AdjustmentAdjustable
CapacityMessage CapacityTF card inserted: 200 captured pictures, 200 alarm records. Without TF card: 2 MB RAM for picture storage; 200 alarm records.
Linked Indoor Extensions Capacity16
Linked Doorphone Capacity17
Network ParametersNetwork ProtocolTCP/IP, SIP, RTSP
Wi-Fi2.4 GHz, IEEE802.11b, IEEE802.11g, IEEE802.11n
Network Interface1 RJ-45 10/100 Mbps self-adaptive
GeneralWeightNet: 355 g (0.8 lb), Gross: 683 g (1.5 lb)
Working Temperature-10°C to 55°C (14°F to 131°F)
Dimension (W x H x D)200 mm x 140 mm x 15.1 mm (7.9" x 5.5" x 0.6")

8. User Tips

  • Power Supply: Ensure you have a compatible PoE switch or power supply, as it may not be included in all kits. The kit includes two power supplies, but for PoE functionality, a PoE switch is required.
  • Network Configuration: For initial setup, ensure your computer and the intercom devices are on the same subnet for easier web activation.
  • Outdoor Installation: When installing the door station outdoors, use the protective shield and apply silicone sealant around cable entries to prevent water ingress.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official HIKVISION website or contact your local distributor. A comprehensive user manual in PDF format is available for download:

Download User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.