1. Product Overview
This Mini 12V Illuminator LED Light Source is a high-brightness fiber optic lighting generator, designed for DIY car atmosphere lights, step lights, engine bay decoration, and home fiber optic lighting projects. It delivers stable, long-lasting light output to drive fiber optic cables, creating customizable ambient lighting effects.

Figure 1: Mini 12V LED Light Source Illuminators and their illuminated output.
2. Package Contents
Please check the package for the following items:
- 2 x Mini 12V LED Light Source (with pre-wired power leads)
- 1 x User Manual (this document)
3. Specifications
| Parameter | Details |
|---|---|
| Brand Name | Ritesdepot |
| Model Number | 1.5W |
| Item Type | Optic Fiber Lights |
| Input Voltage | DC 12V (compatible with 12V car electrical systems) |
| Power | 1.5W |
| Power Source | DC (Car 12V power supply, 12V DC adapter) |
| Available Inner Diameter | 3mm / 5mm / 6mm / 8mm / 10mm (matches fiber optic cable outer diameter) |
| Available Emitting Color | Red, Blue, Warm White, Yellow, Green, Ice Blue, Cold White, Pink, Purple, Orange |
| Working Temperature | -40°C ~ +85°C |
| Lifespan | >50,000 hours |
| Material | Aluminum alloy housing (heat dissipation) + copper wiring |
| Length | 38mm |
| Diameter | 13.5mm |
| Luminous Flux | <60 |
| Is Bulbs Included | Yes |
| Installation Method | Self-contained |
| Certification | CE |

Figure 2: Available Emitting Colors.
4. Setup (Installation Instructions)
4.1 Pre-Installation Check
- Fiber Optic Cable Diameter: Confirm your fiber optic cable's outer diameter matches the light source's inner diameter (e.g., 10mm cable for 10mm light source).
- Emitting Color: Verify the light source's emitting color matches your requirement.
- Power Supply: Ensure the power supply is 12V DC. Do not connect to 24V or AC power, which will damage the product.
- Cable Preparation: Cut the end of the fiber optic cable flat and clean to ensure maximum light transmission.
4.2 Installation Steps
- Fiber Optic Connection: Insert the flat-cut end of the fiber optic cable fully into the light source's fiber port until it reaches the LED chip. Secure the cable (use heat shrink tube or cable tie if needed) to prevent loosening.

Figure 3: Fiber Optic Connection Point.
- Wiring Connection:
- Red Wire: Connect to the positive (+) terminal of the 12V power supply (e.g., car ACC power, 12V battery positive).
- Black Wire: Connect to the negative (-) terminal of the 12V power supply (e.g., car chassis ground, battery negative).

Figure 4: Light Source with Pre-wired Leads.
- Fix the Light Source: Mount the light source in a dry, well-ventilated location (avoid direct water splash, high-temperature areas like engine exhaust pipes). Use double-sided tape or zip ties for secure installation.
- Test the Light: Power on the 12V supply to confirm the LED lights up and the fiber optic cable emits light evenly.
5. Operating (Usage Notes)
- Do Not Disassemble: Never open the aluminum housing, as this will damage the LED chip and void the warranty.
- Power Safety: Do not reverse the positive/negative wiring, which will cause permanent damage to the product.
- Fiber Care: Avoid sharp bends or crushing of the fiber optic cable, as this will reduce light output.
- Heat Dissipation: Keep the light source's aluminum housing unobstructed to ensure proper heat dissipation during long-term use.
- Waterproof: This product is not fully waterproof. Do not install it in areas exposed to direct water (e.g., car wheel wells, outdoor rain areas).
- Built-in Switch: The built-in switch can be used to manually turn the light on/off after wiring.
6. Maintenance
- Wiring Connections: Regularly check the wiring connections to prevent loose contacts.
- Cleaning: Clean the fiber optic cable end and light source port with a soft cloth if dust accumulates, to maintain light brightness.
- Inspection: If the light dims or fails to turn on, first check the power supply and wiring, then inspect the fiber optic cable for damage.
7. Troubleshooting
| Issue | Possible Cause | Solution |
|---|---|---|
| LED does not light up | 1. Reverse positive/negative wiring 2. No power supply 3. Loose wiring | 1. Correct the wiring polarity 2. Check 12V power supply 3. Reconnect and secure the wires |
| Low light output from fiber | 1. Fiber end not cut flat 2. Dust in the light source port 3. Fiber cable bent sharply | 1. Re-cut the fiber end flat 2. Clean the port with a soft cloth 3. Adjust the cable to avoid sharp bends |
| LED flickers | 1. Unstable power supply 2. Loose wiring connection | 1. Check the car power supply or 12V adapter 2. Tighten all wiring connections |
8. Safety Warnings
- Power Source: Only use 12V DC power. Do not connect to 24V, 110V/220V AC power, which will cause fire or product damage.
- Professional Installation: For car installation, if you are not familiar with automotive electrical systems, please hire a professional technician to avoid damaging the car's electrical system.
- Children: Store the product out of reach of children to prevent electric shock or injury.
- Intended Use: This product is only for fiber optic ambient lighting; do not use it for medical, industrial, or other high-risk applications.
9. User Tips
- This light source is ideal for various DIY projects, including car footwell lights, door step lights, starry sky roof lights, and home fiber optic ceiling lights.
- Users have noted the excellent quality of the light output, such as a