Ritesdepot 1.5W

Contents

Mini 12V Illuminator LED Light Source User Manual

Model: 1.5W

Brand: Ritesdepot

1. Product Overview

This Mini 12V Illuminator LED Light Source is a high-brightness fiber optic lighting generator, designed for DIY car atmosphere lights, step lights, engine bay decoration, and home fiber optic lighting projects. It delivers stable, long-lasting light output to drive fiber optic cables, creating customizable ambient lighting effects.

Mini 12V LED Light Source and glowing fiber optic cables
The Mini 12V LED Light Source with connected fiber optic cables.

2. Package Contents

  • 2 x Mini 12V LED Light Source (with pre-wired power leads)
  • 1 x User Manual (this document)
Multiple Mini 12V LED Light Sources with pre-wired leads
A set of Mini 12V LED Light Sources, as typically included in the package.

3. Product Specifications

ParameterDetails
Input VoltageDC 12V (compatible with 12V car electrical systems)
Available Inner Diameter3mm / 5mm / 6mm / 8mm / 10mm (matches fiber optic cable outer diameter)
Emitting ColorRed, Blue, Warm White, Yellow, Green, Ice Blue, Cold White, Pink, Purple, Color autochanging
Power SourceCar 12V power supply, 12V DC adapter
Working Temperature-40°C ~ +85°C
Lifespan>50,000 hours
MaterialAluminum alloy housing (heat dissipation) + copper wiring
Power1.5W
Length38mm
Diameter13.5mm
Luminous Flux<60
Is Bulbs IncludedYes
Installation MethodSelf-contained
CertificationCE

For a detailed PDF version of this manual, please refer to the Item guides & documents (PDF).

4. Setup

4.1 Pre-Installation Check

  1. Confirm your fiber optic cable's outer diameter matches the light source's inner diameter (e.g., 10mm cable for 10mm light source).
  2. Verify the light source's emitting color matches your requirement.
  3. Ensure the power supply is 12V DC (do not connect to 24V or AC power, which will damage the product).
  4. Cut the end of the fiber optic cable flat and clean to ensure maximum light transmission.

4.2 Installation Steps

1. Fiber Optic Connection:

Insert the flat-cut end of the fiber optic cable fully into the light source's fiber port until it reaches the LED chip. Secure the cable (use heat shrink tube or cable tie if needed) to prevent loosening.

Close-up of the light source showing the screw to fix the fiber
Close-up view of the light source, indicating the screw to secure the fiber optic cable.

2. Wiring Connection:

The light source comes with pre-wired power leads (red and black).

  • Red Wire: Connect to the positive (+) terminal of the 12V power supply (e.g., car ACC power, 12V battery positive).
  • Black Wire: Connect to the negative (-) terminal of the 12V power supply (e.g., car chassis ground, battery negative).
Mini 12V LED Light Source with red and black pre-wired power leads
The light source showing its pre-wired red (positive) and black (negative) leads.

3. Fix the Light Source:

Mount the light source in a dry, well-ventilated location (avoid direct water splash, high-temperature areas like engine exhaust pipes). Use double-sided tape or zip ties for secure installation.

4. Test the Light:

Power on the 12V supply to confirm the LED lights up and the fiber optic cable emits light evenly.

Fiber optic cable glowing green from the light source
Example of a fiber optic cable glowing green when connected to the light source.
Various colors of light emitted from fiber optic cables
Different color options for the fiber optic lighting.

5. Operating (Usage Notes)

  • Do not disassemble: Never open the aluminum housing, as this will damage the LED chip and void the warranty.
  • Power safety: Do not reverse the positive/negative wiring, which will cause permanent damage to the product.
  • Fiber care: Avoid sharp bends or crushing of the fiber optic cable, as this will reduce light output.
  • Heat dissipation: Keep the light source's aluminum housing unobstructed to ensure proper heat dissipation during long-term use.
  • Waterproof: This product is not fully waterproof. Do not install it in areas exposed to direct water (e.g., car wheel wells, outdoor rain areas).

Note: The built-in switch can be used to manually turn the light on/off after wiring.

6. Maintenance

  • Regularly check the wiring connections to prevent loose contacts.
  • Clean the fiber optic cable end and light source port with a soft cloth if dust accumulates, to maintain light brightness.
  • If the light dims or fails to turn on, first check the power supply and wiring, then inspect the fiber optic cable for damage.

7. Troubleshooting

IssuePossible CauseSolution
LED does not light up
  • 1. Reverse positive/negative wiring
  • 2. No power supply
  • 3. Loose wiring
  • 1. Correct the wiring polarity
  • 2. Check 12V power supply
  • 3. Reconnect and secure the wires
Low light output from fiber
  • 1. Fiber end not cut flat
  • 2. Dust in the light source port
  • 3. Fiber cable bent sharply
  • 1. Re-cut the fiber end flat
  • 2. Clean the port with a soft cloth
  • 3. Adjust the cable to avoid sharp bends
LED flickers
  • 1. Unstable power supply
  • 2. Loose wiring connection
  • 1. Check the car power supply or 12V adapter
  • 2. Tighten all wiring connections

8. Safety Warnings

  • Only use 12V DC power: Do not connect to 24V, 110V/220V AC power, which will cause fire or product damage.
  • Professional installation recommended: For car installation, if you are not familiar with automotive electrical systems, please hire a professional technician to avoid damaging the car's electrical system.
  • Keep away from children: Store the product out of reach of children to prevent electric shock or injury.
  • Do not use for other purposes: This product is only for fiber optic ambient lighting; do not use it for medical, industrial, or other high-risk applications.

9. Warranty & Support

  • This product comes with a 1-year limited warranty from the date of purchase, covering manufacturing defects.
  • The warranty is void for damage caused by incorrect wiring, misuse, disassembly, or water damage.
  • For after-sales support, please contact our customer service with your order number.

10. User Tips

  • This product is ideal for DIY projects such as car footwell lights, door step lights, starry sky roof lights, and home fiber optic ceiling lights.
  • Ensure the fiber optic cable end is cut perfectly flat and clean for optimal light transmission.
  • When installing in a vehicle, consider using a fuse for protection and connecting to an ignition-switched power source (like ACC) to prevent battery drain.

11. Frequently Asked Questions (FAQ)

Q: What is the length of the fiber optic cables?
A: The Mini 12V Illuminator LED Light Source does not include fiber optic cables. These are sold separately and are available in various lengths and diameters to suit your project needs.
Q: How many individual fibers can enter the illuminator?
A: This illuminator is designed to connect to a single fiber optic cable, typically a side-glow type, with an inner diameter matching the light source's output coupling size (e.g., 3mm). It is not designed to accept multiple individual thin fibers.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.