Flysky FS-R6B Receiver

Contents

FlySky FS-R6B 2.4Ghz 6CH RC Receiver Instruction Manual

Model: FS-R6B Receiver

1. Introduction

The FlySky FS-R6B is a 2.4Ghz 6-channel receiver designed for use with various FlySky transmitters, including models like the FS-i6, FS-i10, T6, CT6B, and TH9x. Utilizing GFSK modulation and AFHDS (Automatic Frequency Hopping Digital System) technology, this receiver provides a reliable and stable connection for your remote control aircraft and other vehicles. This manual will guide you through the setup, operation, and maintenance of your FS-R6B receiver.

2. Package Contents

  • 1x FlySky FS-R6B 2.4Ghz 6CH Receiver
  • 1x Bind Plug
FlySky FS-R6B 6-channel RC receiver with bind plug
FlySky FS-R6B 6-channel RC receiver with included bind plug.

3. Product Overview

The FS-R6B receiver features six standard servo channels, a dedicated battery port, and a bind port. Its compact design makes it suitable for various RC models.

Close-up view of FlySky FS-R6B receiver ports, showing CH1 to CH6, BAT, and Bind ports
Close-up of the FS-R6B receiver showing channel ports (CH1-CH6), BAT port, and BIND port.

Port Identification:

  • CH1 - CH6: Standard servo output channels. Connect your servos, ESCs, or other control devices here.
  • BAT: Battery input port. Used to power the receiver, typically from an ESC's BEC or a dedicated receiver battery.
  • BIND: Used for the binding process to link the receiver with your transmitter.

4. Setup and Binding

Before operating your RC model, the receiver must be properly connected and bound to your FlySky transmitter.

4.1. Connections

Connect your servos, Electronic Speed Controller (ESC), and other components to the appropriate channels on the receiver. Ensure correct polarity (signal, positive, negative) for all connections.

4.2. Binding Procedure

To establish a secure link between your FS-R6B receiver and your FlySky transmitter, follow these steps:

  1. Ensure your transmitter is turned OFF.
  2. Insert the bind plug into the 'BIND' port on the FS-R6B receiver.
  3. Connect power to the receiver via the 'BAT' port or any channel port (e.g., from an ESC's BEC). The receiver's LED should begin to flash rapidly, indicating it is in bind mode.
  4. While holding down the 'BIND' button on your FlySky transmitter (or activating bind mode through its menu), turn on the transmitter.
  5. Observe the receiver's LED. It should stop flashing and remain solid, indicating a successful binding.
  6. Release the 'BIND' button on the transmitter and then turn the transmitter OFF.
  7. Disconnect power from the receiver and remove the bind plug.
  8. Reconnect power to the receiver.
  9. Turn on your transmitter. The receiver's LED should now be solid, confirming that the receiver is linked and receiving a signal from the transmitter.

If the LED continues to flash or does not light up, repeat the binding procedure.

5. Operation

Once the receiver is successfully bound to your transmitter, you can begin operating your RC model. Ensure all control surfaces and motor functions respond correctly to your transmitter inputs before flight or driving.

5.1. Low Voltage Warning

The receiver features an LED low voltage warning. If the input voltage drops below a safe operating level, the LED will indicate this, prompting you to land or stop your model to prevent loss of control.

5.2. Compatibility

The FS-R6B receiver is compatible with a range of FlySky transmitters using the AFHDS protocol. Refer to the pairing table below for specific compatibility details.

FlySky FS-R6B receiver shown with various compatible FlySky transmitters including FS-i4, FS-i6, FS-i10, FS-GT2E, FS-GT2G, FS-T4B, FS-GT6B, FS-T6, FS-TH9X, FS-GT2, FS-GT3B, FS-GT3C
The FS-R6B receiver is compatible with a wide range of FlySky transmitters.
Transmitter and receiver pairing table for FlySky devices, indicating successful pairing with a checkmark for various transmitter models (GR3E, R6B, R9B, A3, BS3, BS4, BS6, A6, iA6, iA6B, X6B, A8S, iA8S, iA10, iA10B) and receiver types (1st generation, 2A generation)
FlySky Transmitter and Receiver Pairing Table. A checkmark indicates successful pairing.

Video: Overview of the FlySky FS-R6B receiver, showing its physical features and connections.

6. Maintenance

To ensure the longevity and optimal performance of your FS-R6B receiver, follow these maintenance guidelines:

  • Keep the receiver clean and free from dust, dirt, and moisture.
  • Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
  • Regularly inspect all connections for signs of wear or damage.
  • Ensure the antenna is not cut, bent sharply, or damaged, as this can affect signal range.

7. Troubleshooting

If you encounter issues with your FS-R6B receiver, try the following troubleshooting steps:

  • Receiver LED not solid after binding: Re-perform the binding procedure carefully. Ensure the bind plug is fully inserted and the transmitter is in bind mode.
  • No control response: Check all connections between the receiver, servos, and ESC. Ensure the receiver is powered and the transmitter is on and correctly bound. Verify battery levels in both the transmitter and the model.
  • Limited range or intermittent signal: Check the receiver antenna for damage or improper placement. Ensure it is not shielded by carbon fiber or metal components. Avoid operating in areas with high RF interference.
  • Receiver not powering on: Check the power source (battery or BEC) and its connections to the receiver. Ensure the voltage is within the specified range (5V DC).

8. Specifications

Detailed technical specifications for the FlySky FS-R6B receiver:

FeatureSpecification
Item NameFS-R6B Receiver
Brand NameFlysky
Channels6 Channels
Model TypeHeli/Airplane
RF PowerLess than 20DBm
ModulationGFSK
Code TypePCM
Sensitivity1024
Low Voltage WarningLED
Charger PortYes
Antenna Length26mm
Frequency2.4G
Power5V DC (1.5V AAA*4)
Weight25g
Dimensions (L*W*H)30mm * 25mm * 8mm
CertificatesCE, FCC, RoHS
Recommended Age14+ years
UseVehicles & Remote Control Toys
Dimensions of FlySky FS-R6B receiver: 45mm length, 23mm width, 13mm height
Physical dimensions of the FS-R6B receiver.

9. User Tips

Based on general user experiences with RC receivers:

  • Always perform a range check before the first flight or operation of a new model or after any significant changes to your RC system.
  • Mount the receiver securely in your model to prevent vibrations from affecting its performance.
  • Position the antenna away from metal parts, carbon fiber, and other electronics to maximize signal reception.
  • Ensure your transmitter batteries are fully charged before each use to avoid unexpected signal loss.

10. Warranty and Support

For warranty information or technical support, please refer to the official FlySky website or contact your retailer. Keep your proof of purchase for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.