VBTER VBT-99

Contents

VBTER VBT-99 Mini Two-Way Radio User Manual

Model: VBT-99 | Brand: VBTER

Introduction

This manual provides detailed instructions for the safe and effective operation and maintenance of your VBTER VBT-99 Mini Two-Way Radio. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.

Safety Information

Adhering to these safety guidelines will help prevent injury and damage to your radio:

  • Do not operate the radio in explosive atmospheres (e.g., near flammable gases, dust particles, or metallic powders).
  • Avoid exposing the radio to direct sunlight for extended periods or placing it near heating appliances.
  • Keep the radio away from medical devices to prevent potential interference.
  • Use only VBTER approved batteries and charging accessories.
  • Do not attempt to disassemble, modify, or repair the radio yourself. Refer to qualified service personnel.
  • Ensure the antenna is properly attached before transmitting to avoid damage to the radio.

Package Contents

The VBTER VBT-99 package typically includes the following items:

  • VBTER VBT-99 Two-Way Radio (1 or 2 units, depending on purchase)
  • Antenna (2 units)
  • Belt Clip (2 units)
  • Rechargeable Battery (2 units)
  • Lanyard (2 units)
  • Type-C Charging Cable (2 units)
Package contents including two VBTER VBT-99 radios, two antennas, two belt clips, two rechargeable batteries, two lanyards, and two Type-C charging cables.
Illustration of the VBTER VBT-99 package contents.

Getting Familiar with Your Radio

Before operation, familiarize yourself with the main components and controls of the VBTER VBT-99 radio:

Diagram of the VBTER VBT-99 radio with labeled parts: Antenna, Indicator light, PTT switch, MONI key, Mic/speaker port, Channel knob, Power/volume knob, Speaker, Microphone, Li-ion battery.
VBTER VBT-99 Component Diagram
  • Antenna: Essential for transmitting and receiving radio signals.
  • Indicator Light: Illuminates red during transmission, green during reception. Blinks red to indicate a low battery condition.
  • PTT Switch (Push-to-Talk): Press and hold to transmit your voice; release to listen for incoming transmissions.
  • MONI Key (Monitor): Used to temporarily disable the squelch and listen to weak signals or activity on the channel.
  • Mic/Speaker Port: Connects external audio accessories like headsets or programming cables.
  • Channel Knob: Rotary switch to select one of the 16 available communication channels.
  • Power/Volume Knob: Rotates clockwise to power on the radio and increase volume; counter-clockwise to decrease volume and power off.
  • Speaker: Outputs received audio.
  • Microphone: Captures your voice for transmission.
  • Li-ion Battery: Provides portable power to the radio.

Setup Guide

1. Attaching the Antenna

Carefully screw the antenna into the threaded connector on the top of the radio. Turn clockwise until it is finger-tight. Do not use excessive force to avoid damaging the connector.

2. Installing the Battery

Align the rechargeable Li-ion battery pack with the battery compartment on the back of the radio. Slide the battery upwards along the grooves until it securely locks into place. To remove the battery, press the release latch (if available) and slide the battery downwards.

3. Charging the Battery

The VBTER VBT-99 is equipped with a convenient Type-C charging port. Connect the provided Type-C charging cable to the radio's port and plug the other end into a compatible USB power source (e.g., a computer USB port, a USB wall adapter, or a power bank). The indicator light will typically show the charging status (e.g., red for charging, green for fully charged).

Close-up of the VBTER VBT-99 radio being charged via a Type-C cable connected to a laptop, illustrating the charging process.
Type-C Charging in progress.

4. Attaching the Belt Clip and Lanyard

Attach the belt clip to the designated area on the back of the radio using the provided screws. Secure the lanyard to the loop on the radio for convenient carrying and to prevent accidental drops.

Operating Instructions

1. Power On/Off and Volume Adjustment

Rotate the Power/Volume knob clockwise to turn on the radio. Continue rotating clockwise to increase the listening volume. To decrease the volume and turn off the radio, rotate the knob counter-clockwise.

2. Channel Selection

Use the Channel knob to select your desired communication channel, from 1 to 16. Rotate counter-clockwise to select a lower channel number, and clockwise for a higher channel number.

3. Transmitting and Receiving (PTT)

  • To Transmit: Press and hold the PTT switch. Speak clearly into the microphone. The indicator light will turn red. If the channel does not have a transmitting frequency, a "DU DU" tone will sound.
  • To Receive: Release the PTT switch. The indicator light will turn green when an incoming signal is detected.

4. Squelch Level

The squelch level controls the minimum signal strength required to open the radio's speaker. A lower squelch level allows weaker signals to be heard but may increase background noise. A higher squelch level reduces noise but might filter out weak, legitimate signals. The default squelch level is 5. Levels from 0 (lowest) to 9 (highest) can be adjusted via the programming software.

5. Monitor Function

Press the MONI key to temporarily open the squelch. This allows you to listen to all activity on the current channel, including weak signals or signals with different DCS codes that would normally be blocked by the squelch setting.

6. Time-Out Timer (TOT)

The TOT feature prevents any single transmission from exceeding a pre-set duration, protecting the radio from overheating and preventing a single user from monopolizing a channel. If your transmission exceeds the TOT limit, the radio will emit a "DU" sound and automatically stop transmitting. Release the PTT key to reset the timer and return to receive mode.

7. Scan Function

When the radio is set to channel 16, it can automatically scan through the 16 pre-defined channels. Upon detecting a signal, the radio will pause on that channel, allowing you to listen or communicate. After approximately 10 seconds of signal loss, the radio will resume scanning.

  • Note: The scan function requires at least two scannable channels to be defined.
  • To exclude a specific channel from the scan list, set its "Scan Add" option to "No" in the programming software.

8. Voice Prompt

The radio can provide audible voice prompts for various operations. You can select between "English" voice prompts or disable them ("None") using the programming software.

9. Battery Save Function

This feature, configurable via the programming software, optimizes power consumption to extend the radio's standby time, conserving battery life when the radio is not actively transmitting or receiving.

10. Low Battery Alert

When the battery voltage drops below a critical level, the radio will alert you. If voice prompts are disabled, a "DuDu" tone will sound every 15 seconds. If voice prompts are enabled, the radio will announce "please charge." During this state, PTT or VOX transmission may be disabled, and the "please charge" prompt will continue until the battery is recharged.

11. Busy Channel Lock (BCL)

If Busy Channel Lock is enabled, the radio will prevent you from transmitting on a channel that is currently in use. If you press the PTT key while a signal is being received, a "Di" sound will ring, and transmission will be inhibited until the channel is clear or the PTT key is released.

12. Wide/Narrow Bandwidth Select

The radio supports both wide and narrow bandwidth modes. The default setting is wide band. This option can be configured through the programming software to match the bandwidth requirements of your communication environment.

13. VOX (Voice Operated Exchange)

The VOX function enables hands-free transmission, allowing you to transmit simply by speaking into the microphone without needing to press the PTT key. This feature can be activated or deactivated via the programming software.

  • When VOX is active, speak directly into the microphone to initiate transmission. The radio will automatically stop transmitting when no voice is detected.
  • If using a headset, adjust the VOX gain level in the software to ensure proper voice detection and to prevent accidental transmissions from background noise.

14. Scrambler

The scrambler function provides an added layer of privacy by encrypting your voice transmissions. This feature can be individually enabled or disabled for each channel using the programming software.

15. CTCSS/DCS (Continuous Tone-Coded Squelch System / Digital Coded Squelch)

CTCSS and DCS tones are sub-audible tones that can be set via the programming software. When a CTCSS/DCS tone is configured for a channel, the radio's squelch will only open if the incoming signal carries the identical tone, effectively filtering out unwanted transmissions from other users on the same frequency.

16. Programming Protection

The programming software interface allows you to set a password to protect your radio's configuration settings from unauthorized access or modification.

17. Special Signal

This function, active when DCS is enabled, prevents radios within the same DCS group from hearing the content of calls, further enhancing communication privacy.

18. One-Key Frequency Copy (Optional)

This feature allows for quick copying of frequencies from another radio. This function is typically available on radios marked with a "PLUS" label.

  1. With your radio powered off, press and hold both the PTT key and MONI key simultaneously, then power on the radio. Ensure your radio is set to Channel 1.
  2. Your radio will broadcast "turn on the radio one" and its green indicator light will flash slowly. Rotate the Channel knob to the desired channel where you want to save the copied frequency.
  3. On the source radio (the one you wish to copy from), initiate a transmission (press PTT). Your radio will then copy the current frequency and CTCSS/DCS settings. The green light on your radio will flash quickly twice, followed by a "Di" prompt sound and the green light remaining solid, indicating successful saving.
  4. Repeat this process for other channels as needed.
  5. Once all desired frequencies are copied, power off your radio and then power it back on to finalize the settings.
  6. This method supports copying frequencies between walkie-talkies of different bands.

19. Frequency Copy (Optional)

This feature allows for copying all channels simultaneously from another radio. This function is typically available on radios marked with a "PLUS" label.

  1. With your radio powered off, press and hold both the PTT key and MONI key simultaneously, then power on the radio. Ensure your radio is set to Channel 2. Both the source and target radios must be in the same operating mode.
  2. The green indicator light on your radio will flash slowly.
  3. On the source radio (the one you wish to copy from), initiate a transmission (press PTT) for approximately 3 seconds. The green light on your radio will flash quickly for about 1 second and then return to slow flashing, indicating that all channels have been successfully saved.
  4. Finally, power off your radio and then power it back on to finalize the settings.
  5. This method only supports copying between walkie-talkies that use the same solution/model.

Care and Maintenance

  • Cleaning: Use a soft, slightly damp cloth to clean the radio's exterior. Do not use harsh chemicals, solvents, or abrasive cleaners, as these can damage the casing.
  • Battery Care: To maximize battery lifespan, avoid completely discharging the battery frequently and do not leave it on charge indefinitely after it's full. Store the radio and battery in a cool, dry place when not in use for extended periods.
  • Water and Dust Resistance: The VBTER VBT-99 is rated IP45, meaning it is protected against dust ingress and low-pressure water jets from any direction. While durable, it is not designed for submersion. Avoid direct exposure to heavy rain or prolonged water spray.
  • Storage: When storing the radio for a long duration, remove the battery pack and store both components in a dry, dust-free environment at room temperature.
VBTER VBT-99 radio in a dusty, rocky environment, illustrating its shockproof and dustproof features.
The VBTER VBT-99 is designed to be shockproof and dustproof (IP45 rated).

Troubleshooting

ProblemPossible CauseSolution
Radio does not power on.Battery is dead or not installed correctly.Charge the battery fully or re-install it correctly, ensuring good contact.
Cannot transmit (PTT produces "DU DU" tone).No transmitting frequency defined for the selected channel.Verify channel settings using the programming software. Ensure the channel is configured for transmission.
Cannot receive signals or reception is poor.Antenna not attached, squelch level too high, or different CTCSS/DCS tone.Ensure the antenna is securely attached. Adjust the squelch level (lower it if necessary). Verify CTCSS/DCS settings match the transmitting radio.
Radio stops transmitting unexpectedly.Time-Out Timer (TOT) activated.Release the PTT key and wait for TOT to reset. Avoid excessively long transmissions.
Radio does not scan channels.Less than 2 scannable channels defined, or scan function disabled for channels.Ensure at least two channels are configured for scanning. Check "Scan Add" settings for each channel in the programming software.
"Please charge" prompt or "DuDu" sound.Low battery.Charge the radio immediately using the provided Type-C cable.
Cannot transmit while receiving.Busy Channel Lock (BCL) is enabled.Wait for the channel to clear before transmitting. If necessary, BCL can be disabled via the programming software.

Specifications

General

FeatureSpecification
Model NumberVBT-99
Brand NameVBTER
Walkie Talkie TypePortable
Frequency RangePMR446MHz (446-446.2MHz)
Storage Channel16
Maximum Range3km-5km
Working Voltage3.7V
Battery Capacity1800mAh
Battery IncludedYes (Rechargeable)
Working Temperature-20℃ ~ +50℃
Waterproof / Water-ResistantIP45
MaterialPlastic
Is DisplayNo
CertificationCE, FCC, RoHS

Transmitter

FeatureSpecification
Output Power2W (Note: Some product descriptions indicate 3W-5W, but the OCR specification table states 2W. PMR446 radios typically operate at 0.5W in Europe.)
Modulation Type16KF3E
Spurious Radiation≤7.5 µW
Modulation Noise<-40dB
Modulation Response<5%
Frequency Tolerance5ppm

Receiver

FeatureSpecification
Sensitivity≤0.2 μV
Occupied Bandwidth≤16KHz
Channel Selective≥65dB
Inter-modulation≥55dB
Audio Power>500mW
Audio Distortion≤5%
Frequency Tolerance5ppm
Current150mA
Audio Response (300-3000Hz)+7~12.5dB

User Tips

  • Optimal Range: For the best communication range, try to maintain a clear line of sight between radios and avoid major obstructions like buildings or dense foliage.
  • Battery Management: Always fully charge your radio's battery before extended use. Consider carrying a spare charged battery for prolonged operations.
  • Squelch Adjustment: Experiment with different squelch levels in your operating environment to find the optimal balance between filtering out background noise and receiving weaker, distant signals.
  • VOX Sensitivity: If using the VOX function, test the sensitivity settings in a quiet environment first. Adjust it to reliably pick up your voice without triggering from ambient noise.
  • Privacy: Utilize the scrambler function and CTCSS/DCS tones for more private conversations and to minimize interference from other radio users.
  • Programming Software: Familiarize yourself with the programming software to customize channels, squelch levels, VOX settings, and other advanced features to suit your specific needs.

Warranty and Support

Your VBTER VBT-99 radio is covered by a warranty. To avail of warranty services, it is crucial to retain your purchase receipt and the completed warranty card.

Warranty Card Information

The warranty card serves as an essential document for warranty claims. It must be accurately completed by the dealer at the time of purchase and stamped with their official sales stamp to be considered valid. The warranty specifically applies to the model and serial number listed on the card.

Please ensure the following details are filled out on your physical warranty card:

  • Customer's Name
  • Gender
  • Address and Postal Code
  • Customer's Telephone Number
  • Model
  • Serial Number
  • Purchasing Date
  • Invoice Number
  • Dealer Information (Name, Address, Contact Telephone, Handling Personnel, Official Stamp)

For a comprehensive user manual with additional details and support information, you can refer to the official PDF document: VBTER VBT-99 User Manual (PDF).

© 2024 VBTER. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.