MN MODEL MN300

Contents

MN300 RC Car Upgrade Parts Instruction Manual

For MN Model MN-300 RC Car

Introduction

This manual provides detailed instructions for the installation, use, and maintenance of various upgrade parts for your MN Model MN300 RC Car. These accessories are designed to enhance the performance, durability, and aesthetic appeal of your remote-controlled vehicle.

Safety Information

  • Always ensure your RC car is powered off and disconnected from its power source before installing or removing any parts.
  • Some parts may have sharp edges or small components. Handle with care and keep out of reach of small children to prevent choking hazards.
  • Use appropriate tools for installation to avoid damage to the parts or injury.
  • Refer to your MN300 RC Car's original manual for general safety guidelines.

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Package Contents

Depending on your purchase, your package may contain one or more of the following upgrade parts:

  • MN300 Metal K02 Tire (White-metal clip wheel)
  • MN300 Retro Pinch Tire
  • MN300 Universal K02 Tires
  • MN300 Special Hydraulic Shock Absorber
  • MN300 Metal Shock Absorber Base
  • MN300 Metal Drive Shaft
  • MN300 Metal Drive Shaft + Centering Piece
  • MN300 Full Metal Competition Front Bumper
  • MN300 Full Size Luggage Rack
  • MN300 1:12 Kayak (with elastic cord and paddle)
  • MN300 Daddy Sticker
  • MN300 Flame Sticker
  • MN300 Top Flame Sticker
  • MN300 Metal Gear Sleeve
  • MN300 Travel Expansion Decorative Parts (various accessories)

Specifications

Below are the specifications for various MN300 RC Car upgrade parts. Weights are approximate.

PartMaterialDimensions (approx.)Weight (approx.)Notes
MN300 Metal K02 Tire (White-metal clip wheel)Metal, Rubber7cm diameter, 3cm width247.6g
MN300 Retro Pinch TireRubber7.5cm diameter, 3cm width137.1g
MN99S/300 Universal K02 TiresRubber7cm diameter, 3cm width123.9g
MN300 Special Hydraulic Shock AbsorberMetal6.2cm length, 1.4cm width (absorber); 3.8cm length, 1.3cm width (spring)34.9gHole spacing: 54mm, Stroke: 14mm. Refueling, adjustable soft/hard.
MN300 Metal Shock Absorber BaseMetal2.4cm width, 2.3cm height, 1.2cm base width22.9g
MN300 Metal Drive ShaftMetal7cm length, 0.9cm width41.1g
MN300 Metal Drive Shaft + Centering PieceMetal7cm length, 0.9cm width (shaft); 2cm width, 0.5cm height (centering piece)45.5g
MN300 Full Metal Competition Front BumperMetal14cm width, 5cm height109.2g
MN300 Full Size Luggage RackPlastic18.6cm length, 10.5cm width17g
MN300 1:12 KayakPlastic21cm length, 8.5cm width40.2gIncludes elastic cord (13.5cm) and paddle (16.5cm).
MN300 Daddy StickerVinyl29.8cm length, 10.5cm height11g
MN300 Top Flame StickerVinyl13.5cm length, 12.3cm height11.6g
MN300 Metal Gear SleeveMetal6cm length, 2cm width (sleeve); 1.6cm diameter, 0.8cm height (gear)21.7g
MN300 Travel Expansion Decorative PartsPlasticVarious (e.g., boxes 5.8x4cm, ladder 9.5x1.8cm)115.2gIncludes miniature boxes, fuel cans, ladder, shovel, axe, bucket, jack, fire extinguisher.

For a visual demonstration of tire weight, please refer to the video below:

Video: Demonstration of weighing MN300/99S K02 metal wheels and tires.

Setup and Installation

Before beginning any installation, ensure your RC car is turned off and the battery is disconnected. Use appropriate small tools (e.g., screwdrivers, hex wrenches) as needed.

1. Tire Installation (K02, Retro Pinch, Metal K02 Clip Wheel)

  1. Carefully remove the existing tires and wheels from your MN300 RC car. This usually involves unscrewing the wheel nuts.
  2. Mount the new tires onto the wheel hubs. For clip wheels, ensure the tire bead is properly seated in the wheel groove.
  3. Attach the new wheel assemblies to the RC car's axles, ensuring they are securely fastened with the wheel nuts. Do not overtighten.
MN300 Retro Pinch Tire comparison

Image: Comparison of original factory tires versus MN300 Retro Pinch Tires.

MN300 White-Metal K02 tire clip wheel comparison

Image: Comparison of original factory tires versus MN300 White-Metal K02 Tire Clip Wheels.

MN99S/300 Universal K02 Tires comparison

Image: Comparison of original factory tires versus MN99S/300 Universal K02 Tires.

2. Shock Absorber Installation (Hydraulic Shock Absorber, Metal Base)

  1. Remove the original shock absorbers from your RC car.
  2. If installing the metal shock absorber base, attach it to the chassis first.
  3. Install the new hydraulic shock absorbers, ensuring they are correctly oriented and securely fastened at both ends.
  4. For hydraulic shock absorbers, you may need to adjust the spring tension (soft/hard) according to your preference and driving conditions.
MN300 Special Hydraulic Shock Absorber and Metal Base

Image: MN300 Special Hydraulic Shock Absorber and Metal Shock Absorber Base, showing before and after installation.

3. Drive Shaft & Gear Installation (Metal Drive Shaft, Centering Piece, Metal Gear Sleeve)

  1. Carefully disassemble the relevant sections of your RC car's drivetrain to access the drive shafts and gears.
  2. Replace the original drive shafts with the new metal drive shafts. If using a centering piece, install it as shown in the diagram.
  3. Install the metal gear sleeve, ensuring proper alignment with other drivetrain components.
  4. Reassemble the drivetrain, ensuring all screws and fasteners are secure.
MN300 Metal Drive Shaft + Centering Piece

Image: MN300 Metal Drive Shaft and Centering Piece with dimensions.

MN300 Metal Gear Sleeve

Image: MN300 Metal Gear Sleeve with dimensions.

4. Bumper Installation (Full Metal Competition Front Bumper)

  1. Remove the original front bumper from your MN300 RC car.
  2. Align the new full metal competition front bumper with the mounting points on the chassis.
  3. Secure the bumper using the provided screws or existing hardware. Ensure it is firmly attached.
MN300 Full Metal Competition Front Bumper

Image: MN300 Full Metal Competition Front Bumper, showing multi-angle display and before/after installation.

5. Luggage Rack & Decorative Parts Installation (Full Size Luggage Rack, Kayak, Travel Expansion Decorative Parts)

  1. For the full size luggage rack, attach it to the roof of your RC car using appropriate mounting hardware (not always included, may require drilling small holes).
  2. The 1:12 Kayak can be secured to the luggage rack using the elastic cords provided or other suitable straps.
  3. Travel expansion decorative parts (boxes, fuel cans, ladder, etc.) can be attached to the luggage rack or other suitable areas of the RC car using adhesive or small fasteners for a realistic look.
MN300 Full Size Luggage Rack

Image: MN300 Full Size Luggage Rack, showing before and after installation.

MN300 1:12 Kayak

Image: MN300 1:12 Kayak with accessories, showing before and after installation on an RC car with a luggage rack.

MN300 Travel Expansion Decorative Parts

Image: MN300 Travel Expansion Decorative Parts, showing various items and their application on an RC car.

6. Sticker Application (Daddy Sticker, Flame Sticker, Top Flame Sticker)

  1. Clean the surface of your RC car where the sticker will be applied, ensuring it is free of dust and grease.
  2. Carefully peel the sticker from its backing.
  3. Apply the sticker to the desired location, smoothing out any air bubbles with a soft cloth or squeegee.
MN300 Daddy Sticker

Image: MN300 Daddy Sticker with dimensions, showing before and after application.

MN300 Top Flame Sticker

Image: MN300 Top Flame Sticker with dimensions, showing before and after application.

Operating Considerations

After installing new upgrade parts, consider the following:

  • Weight Distribution: Adding metal parts or decorative accessories will change the overall weight and balance of your RC car. Test its handling at low speeds first.
  • Suspension Adjustment: If you've installed new shock absorbers, fine-tune their settings (e.g., spring tension, oil viscosity if refillable) to match your driving style and terrain.
  • Clearance: Larger tires or new bumpers might affect ground clearance or articulation. Check for any rubbing or interference during full suspension travel and steering.
  • Drivetrain Stress: Heavier wheels or more aggressive tires can put additional stress on the motor and gears. Monitor for signs of overheating or unusual wear.

Maintenance

  • Regular Inspection: Periodically check all installed upgrade parts for looseness, damage, or wear. Tighten screws and nuts as needed.
  • Cleaning: Clean dirt and debris from parts, especially moving components like drive shafts and gears, after each use. Use a soft brush and compressed air.
  • Lubrication: For metal moving parts like drive shafts and gears, apply appropriate RC-grade lubricant periodically to reduce friction and wear.
  • Shock Absorbers: If you have hydraulic shock absorbers, check for leaks and refill with shock oil as necessary. Adjustments can be made to optimize performance.
  • Tires: Inspect tires for punctures, tears, or excessive wear. Replace worn tires to maintain optimal traction.

Troubleshooting

  • Loose Parts: If a part feels loose or rattles, check all mounting screws and tighten them.
  • Unusual Noise: Squeaking or grinding noises from the drivetrain may indicate a need for lubrication or inspection of gears/bearings for damage.
  • Poor Handling: If the RC car handles poorly after installing new parts, re-check suspension settings, tire pressure (if applicable), and ensure all parts are installed symmetrically.
  • Sticker Peeling: Ensure the surface was clean and dry before application. Re-apply with a stronger adhesive if necessary.

User Tips

  • When upgrading to portal axles, ensure you select mounts that do not unnecessarily increase the ride height, maintaining the desired scale look and performance.

Warranty and Support

For warranty information or technical support regarding your MN300 RC Car upgrade parts, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2023 MN MODEL. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.