1. Introduction
This manual provides detailed instructions for the setup, operation, and maintenance of your Flysky FS-GT2E 2.4G 2-channel RC Transmitter and its accompanying FS-A3 3-channel receiver. Designed for RC car and boat models, this system offers reliable control with a 250m range and 1024-step resolution.
2. Package Contents
- 1 x Flysky FS-GT2E Transmitter
- 1 x Flysky FS-A3 Receiver
- 1 x Antenna tube
- 1 x Binding plug

Image: Retail box of the Flysky FS-GT2E system, showing the transmitter and receiver.
3. Product Overview
3.1. FS-GT2E Transmitter
The FS-GT2E transmitter features an ergonomic design for comfortable handling and precise control. Key components include the steering wheel, throttle trigger, and a control panel with various switches and trim adjustments.

Image: Side profile of the FS-GT2E transmitter, highlighting its grip and overall shape.

Image: Detail of the steering wheel and throttle trigger, essential for controlling your RC model.

Image: Detailed diagram illustrating the various controls and indicators on the FS-GT2E transmitter's control panel.
3.2. FS-A3 Receiver
The FS-A3 is a compact 3-channel receiver designed to work seamlessly with the FS-GT2E transmitter, utilizing the AFHDS 2A 2.4G system for stable communication.

Image: The FS-A3 receiver, showing its ports and the included antenna and binding plug.
4. Setup Instructions
4.1. Transmitter Battery Installation
- Open the battery compartment cover on the bottom of the transmitter.
- Insert four (4) AA batteries (not included) into the compartment, ensuring correct polarity (+/-). The transmitter requires 6V DC power.
- Close the battery compartment cover securely.

Image: View of the transmitter's battery compartment, indicating where to insert the AA batteries.
4.2. Receiver Connection
Connect the receiver to your RC model's electronic speed controller (ESC) and steering servo. The FS-A3 receiver has 3 channels:
- Channel 1 (CH1): Steering Servo
- Channel 2 (CH2): Electronic Speed Controller (ESC) / Throttle
- Channel 3 (CH3): Auxiliary (if applicable, e.g., for lights or other functions)
- VCC: Power input (typically from ESC's BEC)

Image: Diagram illustrating the connection ports on the FS-A3 receiver for steering, throttle, auxiliary, and power.
4.3. Binding the Transmitter and Receiver
Binding is the process of linking the transmitter to the receiver, ensuring they communicate exclusively with each other.
- Ensure the transmitter is OFF.
- Connect the binding plug (included) to the BIND port on the FS-A3 receiver.
- Power on the RC model (which powers the receiver). The receiver's LED should flash rapidly.
- While holding down the BIND button on the FS-GT2E transmitter, turn the transmitter ON.
- Release the BIND button on the transmitter once its LED (G.LED) starts flashing or becomes solid.
- The receiver's LED should now be solid, indicating a successful bind.
- Turn off both the transmitter and the receiver.
- Remove the binding plug from the receiver.
- Power on the transmitter first, then the receiver. The system should now be bound and ready for use.

Image: Step-by-step visual guide for binding the transmitter and receiver, showing the bind button and plug placement.
5. Operation
5.1. Basic Controls
- Steering Wheel: Controls the direction of your RC model (left/right).
- Throttle Trigger: Controls forward/reverse movement and speed. Pull for forward, push for reverse.
5.2. Control Panel Functions
Refer to the control panel diagram for the location of these functions:
- ST.REV (Steering Reverse Switch): Reverses the steering channel direction.
- TH.REV (Throttle Reverse Switch): Reverses the throttle channel direction.
- BIND Button: Used for pairing the transmitter with a receiver.
- R.LED (Red LED): Indicates low battery voltage (flashes when voltage is below 4.2V).
- G.LED (Green LED): Indicates power ON and successful binding.
- ST.TRIM (Steering Trim): Adjusts the neutral position of the steering servo.
- TH.TRIM (Throttle Trim): Adjusts the neutral position of the throttle.
- ST.DR (Steering Dual Rate): Adjusts the maximum steering angle.
- Power Switch: Turns the transmitter ON/OFF.
5.3. Low Voltage Warning
The transmitter will alert you with a flashing Red LED (R.LED) when the battery voltage drops below 4.2V. Replace or recharge batteries immediately to avoid loss of control.
6. Maintenance
- Keep the transmitter and receiver clean and free from dust, dirt, and moisture.
- Store the system in a dry, cool place away from direct sunlight.
- Remove batteries from the transmitter if it will not be used for an extended period.
- Regularly check all connections for security and signs of wear.
7. Troubleshooting
- No power to transmitter:
- Check battery installation and ensure batteries are fresh or fully charged.
- No control or erratic control:
- Ensure the transmitter and receiver are properly bound.
- Check all connections between the receiver, ESC, and servos.
- Verify that the transmitter batteries are not low (check R.LED).
- Ensure there is no interference from other 2.4GHz devices nearby.
- Steering/Throttle operates in reverse:
- Adjust the ST.REV or TH.REV switches on the transmitter's control panel.
8. Specifications
8.1. FS-GT2E Transmitter
| Feature | Specification |
|---|---|
| Channels | 2CH |
| Model Type | Car/Boat |
| RF Range | 2.405-2.475GHz |
| Bandwidth | 500KHz |
| Band | 141 |
| RF Power | 20dBm (100mW) max |
| 2.4G System | AFHDS 2A |
| Code Type | GFSK |
| Sensitivity | 1024 |
| Low Voltage Warning | Yes (less than 4.2V) |
| DSC Port | 3.5MM |
| Charge Port | Yes (3.5IN) |
| Power | 4 * AA 6V DC (not included) |
| Antenna Length | 26mm |
| Weight | 243g |
| Size | 210*95*160mm |
8.2. FS-A3 Receiver
| Feature | Specification |
|---|---|
| RF Receiver Sensitivity | -105dBm |
| Modulation | GFSK |
| System Type | AFHDS 2A |
| Sensitivity | 1024 |
| Power Port | Yes (VCC) |
| Power | 4.5~6.5 VDC |
| Weight | 6g |
| Dimensions | 37 * 22 * 12mm |
9. User Tips
- Always turn on the transmitter before the receiver and turn off the receiver before the transmitter to prevent accidental runaway.
- Ensure the receiver antenna is positioned correctly and not obstructed by metal parts for optimal range.
- Periodically check the trim settings to ensure your model tracks straight and stops correctly.
10. Warranty and Support
For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty-related inquiries.