EPEVER TES10415, TES10425

Contents

EPEVER TES Series MPPT Solar Charge Controller User Manual

Models: TES10415, TES10425

1. Product Overview

The EPEVER TES series MPPT solar charge controller is designed to maximize power point tracking efficiency, response speed, and DC/DC conversion efficiency in high and low power bands. It supports various battery types, including lithium batteries, and offers comprehensive electronic protections.

Features

  • Low power consumption with static loss less than 50mA.
  • No-battery mode operation.
  • Advanced MPPT technology, with maximum tracking efficiency not less than 99.5%.
  • Supports two PV inputs to improve PV utilization (for TES8425, TES10415, TES10425).
  • Conversion efficiency up to 98.5%.
  • Supporting multiple battery types, including lithium batteries.
  • Stable self-activation for lithium batteries.
  • Supporting local setting of main control parameters.
  • RS485 communication interface, connected with optional WiFi, Bluetooth, TCP, 4G and other modules for remote monitoring.
  • Dual limits for rated charging power and charging current.
  • Automatic power reduction when charging at high temperature.
  • Comprehensive electronic protections.
  • Rated IP32 protection level.
  • Built-in BMS communication port.
  • Built-in CAN parallel communication port.
  • Real-time data logging, event logging and energy statistics.
  • Compliant with IEC62109, EMC and other relevant standards.
System Diagram of EPEVER TES Series Solar Charge Controller
System Diagram: Illustrates the connection of PV modules (PV1, PV2), communication module, battery, DC/AC inverter, and AC load.

2. Important Safety Instructions

Please keep this manual for future reference. Read all instructions and warnings carefully before installation.

  • No user-serviceable components inside the controller; do not attempt to disassemble or repair.
  • Install the controller indoors to avoid component exposure and water ingress.
  • Install the controller in a well-ventilated place; the heat sink temperature will be very high during operation.
  • Do not install the controller in humid, salt spray, corrosive, greasy, flammable, explosive, dust accumulative or other harsh environments.
  • It is recommended to install proper fast-acting fuses/breakers externally.
  • Disconnect PV array connections and battery fast-acting fuse/breakers before controller installation and adjustment.
  • Check wiring tightness to avoid heat accumulation due to loose connection.
  • The entire system should be installed and operated by professional personnel.
DANGER: Indicates a high-level hazard that, if not avoided, will result in serious injury or death.
WARNING: Indicates a medium-level hazard that, if not avoided, could result in death or serious injury.
CAUTION: Indicates a low-level hazard that, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates an important reminder during operation which, if ignored, may result in an equipment error alarm.

3. Setup (Installation and Connection)

3.1 Product Exterior and Ports

EPEVER TES Series Controller Front View with Labeled Components
Front view of the controller with numbered components.
No.DescriptionNo.Description
1Indicator6Battery terminals
2LCD7PV1 terminals
3Buttons8PV2 terminals
4CAN/RTS/BMS COM interface9Grounding terminal
5COM port (RJ45, with isolation design, 5VDC/200mA)

Note: The CAN/RTS/BMS COM interface (4) is a multi-function multiplexed port. The COM port (5) is an RS485 communication interface.

3.2 Installation Requirements

When installing the controller, ensure sufficient airflow through the heat sink. Leave at least 150mm of clearance above and below the controller for natural convection. If mounted in a closed cabinet, ensure heat can dissipate.

Diagram showing recommended heat dissipation space around the controller
Recommended installation with 150mm clearance for heat dissipation.

3.3 Wire Size

Wiring and installation must conform to national and local electrical codes.

The minimum PV cable specifications are calculated by the PV Isc (short circuit current). Refer to the PV module specifications sheet. The PV array's ISC must not exceed the controller's maximum PV input current.

ModelMaximum Input CurrentMaximum Wire Size
TES6415, TES642560A16mm²/6AWG
TES742575A25mm²/4AWG
TES8415, TES842580A25mm²/4AWG
TES10415, TES10425100A35mm²/2AWG

Note: The wire size is for reference. For long distances between PV array/controller or controller/battery, use thicker cables to reduce voltage drop.

Battery wire size should be selected according to the rated current. Refer to the table above for wiring specifications. For the battery, the recommended wire size is selected according to the conditions that its terminals are not connected to any additional inverter.

3.4 Device Connection

Connect the controller in the sequence of: ① Ground > ② Battery > ③ PV array > ④ Optional accessories. Disconnect in reverse order.

3.4.1 Connecting the Ground Cable (PE)

TES series controllers are common negative. Negative terminals of the PV array and battery can be grounded simultaneously, or any negative terminal can be grounded. The grounding terminal on the shell must be grounded to shield external electromagnetic interference and prevent electric shock.

3.4.2 Connecting the Battery

DANGER: Risk of explosion! Never install the controller in an enclosed space with flooded batteries. Do not reverse battery connections during wiring, as this may damage the controller.
  • Do not connect the circuit breaker or fast-acting fuse when wiring. Ensure "+" and "-" poles are connected correctly.
  • A fast-acting fuse (1.25 to 2 times the controller's rated current) must be installed on the battery side, no longer than 150mm from the battery.
  • Connect the inverter directly to the battery when connecting an inverter in the system.
Wiring diagram for battery mode connection
Wiring diagram for battery mode, showing PV modules, circuit breakers, fuse, and battery connection.

3.4.3 Connecting the PV Modules

DANGER: Electric shock hazard! The PV array can generate very high voltage. Disconnect the circuit breaker before wiring, and ensure "+" and "-" poles are connected correctly.

If the controller is used in an area with frequent lightning strikes, an external surge arrester must be installed at the PV input and utility input terminals.

3.4.4 Connecting the Accessories

a) Connect the BMS-Link module

When using lithium batteries with BMS function, connect the BMS-Link module and lithium batteries through port 4. The BMS-Link module converts BMS protocols from different manufacturers to EPEVER's standard protocols for communication between the controller and the lithium battery BMS. The controller will connect automatically if the correct protocol number is set.

Diagram showing BMS-Link module connection to the controller and lithium battery
BMS-Link module connection for lithium batteries.
b) Connect the remote temperature sensor (model: RTS-D47K)

If the battery has no BMS function, attach the RTS-D47K close to the battery to detect its temperature. This data is transmitted via RS485 communication to improve safety. Set the BMS protocol number to 32 when connecting the remote temperature sensor to the BMS port. If the remote temperature sensor is not connected, the default charging temperature is 25°C without compensation.

Diagram showing remote temperature sensor connection to the controller
Remote temperature sensor connection.
c) Connect the communication module

Connect communication modules (WiFi, Bluetooth, TCP, or 4G) to the RS485 COM port for remote monitoring and parameter modification via APP. Refer to the specific user manuals for these modules.

4. Operating the Device

4.1 Checking Before Powering On

  • Ensure the controller is installed correctly and securely.
  • Verify that terminal wirings are connected correctly.

4.2 Powering On and Basic Operation

Connect the battery's fast-acting fuse to power on the controller. The LCD should display normally, and the charge control terminal should be properly inserted. Then, connect the PV array's circuit breaker. The charging indicator will flash slowly during PV charging.

Tip: If the controller does not work properly or the fault indicator shows an error after powering on, refer to the Troubleshooting section.

4.3 Parameter Setting via LCD

The controller's LCD allows viewing real-time data and setting parameters using the buttons.

a) Indicators/Buttons/LCD

EPEVER TES Series Controller LCD and Buttons
LCD display and control buttons.

Note: The LCD can be viewed clearly when the angle between the end-user's horizontal sight and the LCD is within 90°. If the angle exceeds 90°, the information on the LCD cannot be viewed clearly.

Indicator Status
IndicatorColorStatusDescription
PVGreenSolid ONPV voltage is higher than turn-off voltage, but no charging.
GreenSolid OFFNo sunlight; Connection error; PV low voltage.
GreenSlowly flashing (1Hz)Charging normally.
GreenFast flashing (4Hz)PV input overvoltage, PV mode error, PV input reverse connection, PV power too low.
BATTGreenSolid ONBattery is normal.
GreenSlowly flashing (1Hz)Battery fully charged, SOC low battery alarm.
GreenFast flashing (4Hz)Battery overvoltage, cell overvoltage.
OrangeSolid ONBattery Undervoltage (including battery pack under voltage), cell under voltage.
PV & BATTGreen (fast flashing) & Orange (fast flashing)Equipment over temperature, DSP communication failure.
Button Operations
ButtonOperationDescription
↻ (Return/Exit)Press (< 50ms)Exit the current interface.
▲▼ (Up/Down)Press (< 50ms)Browse interface (Up/Down); Increase/decrease parameter value per step size.
Press and hold (> 2.5s)Increase/decrease parameter value quickly.
↻ (Confirm/Enter)Press (< 50ms)Confirm setting parameters.
Press and hold (> 2.5s)Switch between real-time and setting browsing interfaces; Confirm setting parameters.
LCD Status Icons
NameIconStatus
Day☀️Daytime operation.
Night🌙Nighttime operation.
PV array☉️ (with slash)Not charging.
PV array☉️Charging (B, E, F refer to bulk, equalization, float charging).
PV1/PV2PV1/PV2 iconsDisplays input voltage, current, power, and energy for PV1 and PV2.
BatteryBAT iconDisplays battery voltage, charging current, power, SOC, and temperature.

b) PV Real-time Data

After powering on, press the ↻ button to cycle through PV real-time data interfaces, including PV1/PV2 input voltage, current, power, and energy. (Models with single PV input display PV1 only).

c) Battery Real-time Data

From the "PV2 input energy" interface, click the ↻ button to cycle through battery real-time data, including voltage, charging current, charging/discharging power, SOC, and temperature.

d) Parameter Setting Steps

  1. In the PV/battery real-time data browsing interface, press and hold the ↻ button to enter the parameter setting interface.
  2. Use the ▲▼ buttons to select the parameter to be set.
  3. Press and hold the ↻ button to enter the setting interface (parameter value blinks).
  4. Modify the parameter value using the ▲▼ buttons.
  5. Press the ↻ button to confirm the parameter value.
  6. Press the ↻ button to exit the parameter setting interface and return to real-time data browsing.

e) Parameters List

The controller parameters can be modified via PC or APP, except for some read-only parameters. Key parameters include Battery Type (BT), Battery Capacity (BC), Rated Voltage Level (RVL), Overvoltage Disconnect Voltage (OVD), Charging Voltage Limit (CVL), Overvoltage Recovery Voltage (OVR), Equalization Charging Voltage (ECV), Bulk Charging Voltage (BCV), Float Charging Voltage (FCV), Bulk Voltage Recovery (BVR), Low Voltage Recovery (LVR), Undervoltage Alarm Recovery Voltage (UVAR), Undervoltage Alarm Voltage (UVA), Low Voltage Disconnect Voltage (LVD), Discharging Voltage Limit (DVL), Equalize Charging Time (ECT), Bulk Charging Time (BCT), Lithium Battery Protection (LBP), Low Temperature Charging Limit (LTCL), Battery Max Charging Current (MCC), BMS Protocol (BPRO), PV Connection Mode (PCM), Address (ADDR), Baudrate (BAUD), Temperature Unit (TU), Screen Cycle Time (SCT), and Com Port Enable (CPE).

For detailed tables of default values and user-definable ranges for these parameters, please refer to the original user manual (pages 28-32).

5. Maintenance

To maintain long-term working performance, inspect the following items twice a year:

  • Ensure proper ventilation/heat dissipation around the controller; clean dirt or debris from the heat sink.
  • Check insulation of exposed cables for damage (sunlight, friction, pests); repair or replace if necessary.
  • Verify indicator and display consistency with actual equipment operation; address any fault/error displays.
  • Inspect terminal blocks for corrosion, insulation damage, or high-temperature burn marks; ensure terminal screws are tight.
  • If the lightning arrester has failed, replace it promptly to prevent damage to the controller or other equipment.
DANGER: Electric shock hazard! Ensure the power supply of the controller is disconnected when performing maintenance operations.

6. Troubleshooting

This section provides guidance for common issues indicated by the controller's status lights and error codes.

StatusError CodePossible ReasonsTroubleshooting
PV indicator fast flashing greenPOVPV OvervoltageCheck if PV open circuit voltage is too high. Alarm clears when voltage drops below max PV open circuit voltage minus 5V.
PMEPV Work Mode ErrorCheck if PV connection method matches "PCM (PV Connection Mode)" setting.
RPPPV Reverse Polarity ProtectionCheck if PV is connected correctly.
PV indicator solid greenPPLPV Power LowWait for sufficient sunlight.
BATT indicator solid orangeBUVBattery Undervoltage AlarmDisconnect loads, check battery voltage. Recharge battery. Resumes when voltage is above "UVAR".
CUVCell Undervoltage ProtectionCheck BMS communication status or BMS parameters.
BATT indicator solid redBODBattery Over Discharging ProtectionDisconnect loads, check battery voltage. Recharge battery. Resumes when voltage is above "LVR".
BATT indicator fast flashing redBOFBMS Other FaultCheck BMS connection.
BSFBMS Sensor FaultCheck BMS connection.
BATT indicator fast flashing greenLBVELithium Battery Rated Voltage Identification ErrorCheck if lithium battery is connected correctly or if BMS uploaded voltage matches controller battery terminals.
BATT indicator fast flashing greenBOVBattery Overvoltage ProtectionDisconnect charging, check battery voltage. Alarm clears when voltage drops below "OVR".
BATT indicator fast flashing greenCOVCell Overvoltage ProtectionCheck BMS communication status or BMS parameters.
BATT indicator slowly flashing redBOTBattery Over TemperatureEnsure cool, well-ventilated installation. Check charging/discharging current. Resumes when temperature drops below "BATT OTPR".
BLTBattery Low TemperatureCheck ambient temperature. Resumes when temperature is above "LTCL + 2°C".
BATT indicator slowly flashing redCOTCell Over Temperature ProtectionCheck BMS communication status or BMS parameters.
BATT indicator slowly flashing redCLTCell Low TemperatureCheck BMS communication status or BMS parameters.
BATT indicator slowly flashing greenSLBPSOC Low Battery ProtectionCharge the battery to LBAR (Low Battery Alarm Recovery SOC).
BATT indicator slowly flashing greenBOCDBMS Over Current Discharging AlarmCheck BMS communication status or BMS parameters.
BATT indicator slowly flashing greenBOCCBMS Over Current Charging AlarmCheck BMS communication status or BMS parameters.
BATT indicator slowly flashing greenBLCBattery Limit ChargingBMS is normal, no troubleshooting required.
PV indicator fast flashing greenDOTDevice Over TemperatureEnsure cool, well-ventilated installation. Resumes normal charging when temperature drops below "DOT".
PV & BATT indicator fast flashing orangeDCFDSP Communication FaultTurn off controller, wait 5 minutes, then restart. If error persists, contact technical support.

7. Technical Specifications

General Specifications (TES6415, TES8415, TES10415)

ParameterTES6415TES8415TES10415
PV Input (DC) Max. Open-circuit Voltage150V (@lowest temperature); 135V (@25°C)
MPPT Voltage Range(Battery voltage plus 2V, and > 20V) to 108V (@25℃)
Number of MPPTs112
Battery TypeAGM (Default)/GEL/FLD/User
Lithium Battery TypeLFP/NCM/User
Rated Voltage12/24/48VDC or Auto
Rated Charging Current60A80A100A
Rated Charging Power780W/1,560W/3,120W1,040W/2,080W/4,160W1,300W/2,600W/5,200W
Temperature Compensation Coefficient-3mV/°C/2V (Default)
Controller Output Voltage Range8-62V
Static Loss (Enabled Communication)98mA/12V; 60mA/24V; 46mA/48V
Static Loss (Disabled Communication)48mA/12V; 25mA/24V; 14mA/48V
Grounding TypeCommon negative grounding
Communication Method5VDC/200mA (RJ45)
Tracking Efficiency≥ 99.5%
Maximum Conversion Efficiency98.3%98.3%98.4%
Operating Temperature-25°C to +60°C (> 40°C derating)
LCD Operating Temperature-20°C to +70°C
Storage Temperature-30°C to +70°C
Relative Humidity5%-95% (N.C.)
Altitude< 5,000m (> 2,000m derating)
Ingress ProtectionIP32
Pollution DegreeII
Dimensions (L × W × H)270mm × 305mm × 91mm270mm × 305mm × 105mm308mm × 308mm × 119mm
Mounting Hole SizeΦ6.5mm
Weight3.85kg4.9kg6.55kg
Recommended Cable Size6AWG/16mm²
CertificationsEN/IEC61000-6-2; EN/IEC61000-6-4; EN/IEC62109-1; IEC62321

General Specifications (TES6425, TES7425, TES8425, TES10425)

ParameterTES6425TES7425TES8425TES10425
PV Input (DC) Max. Open-circuit Voltage250V (@ lowest temperature); 225V (@25℃)
MPPT Voltage Range(Battery voltage plus 2V, and > 20V) to 180V (@ 25°C)
Number of MPPTs1122
Battery TypeAGM (Default)/GEL/FLD/User
Lithium Battery TypeLFP/NCM/User
Rated Voltage12/24/48VDC or Auto
Rated Charging Current60A75A80A100A
Rated Charging Power780W/1,560W/3,120W975W/1,950W/3900W1,040W/2,080W/4,160W1,300W/2,600W/5,200W
Temperature Compensation Coefficient-3mV/°C/2V (Default)
Controller Output Voltage Range8-62V
Static Loss (Enabled Communication)98mA/12V; 60mA/24V; 46mA/48V
Static Loss (Disabled Communication)48mA/12V; 25mA/24V; 14mA/48V
Grounding TypeCommon negative grounding
Communication Method5VDC/200mA (RJ45)
Tracking Efficiency≥ 99.5%
Maximum Conversion Efficiency98.5%98.4%98.3%98.4%
Operating Temperature-25°C to +60°C (> 40°C derating)
LCD Operating Temperature-20°C to +70°C
Storage Temperature-30°C to +70°C
Relative Humidity5%-95% (N.C.)
Altitude< 5,000m (> 2,000m derating)
Ingress ProtectionIP32
Pollution DegreeII
Dimensions (L × W × H)270mm × 305mm × 105mm270mm × 305mm × 122mm308mm × 308mm × 119mm308mm × 308mm × 119mm
Mounting Hole SizeΦ6.5mm
Weight4.85kg5.5kg6.50kg6.6kg
Recommended Cable Size2AWG/35mm²
CertificationsEN/IEC61000-6-2; EN/IEC61000-6-4; EN/IEC62109-1; IEC62321
Dimensional drawings for various TES series solar charge controller models
Dimensions (Unit: mm) for TES6415, TES6425/TES8415, TES7425, TES8425/TES10415, and TES10425 models.

8. User Tips

  • Optimal Performance: Ensure your PV array voltage and current are within the recommended ranges for your specific controller model to achieve maximum MPPT efficiency.
  • Battery Compatibility: When using lithium batteries, ensure the BMS protocol number is correctly set for seamless communication and protection. Consider using the BMS-Link module for broader compatibility.
  • Temperature Management: For lead-acid batteries without BMS, utilize the remote temperature sensor (RTS-D47K) to ensure accurate temperature compensation during charging, which prolongs battery life.
  • Monitoring: Leverage the communication modules (WiFi, Bluetooth, etc.) to remotely monitor your system's performance and adjust parameters via the mobile app for convenience.
  • Wiring Best Practices: Always use the recommended wire sizes and ensure all connections are tight to prevent voltage drops and overheating.

9. Technical Support

For technical inquiries regarding EPEVER products, please contact us through the following channels:

  • Service Hotline: 010-82894896 / 82894112, 0752-3889706, 0755-89236770
  • Email: sales@epever.com
  • Website: www.epever.com

Any changes to the product or manual are subject to change without prior notice. Version number: V1.0

HUIZHOU EPEVER TECHNOLOGY CO., LTD.
+86-752-3889706
info@epever.com
www.epever.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.