FlySky FS-SR12

Contents

FlySky FS-SR12 12-Channel Receiver User Manual

Model: FS-SR12

1. Introduction

The FlySky FS-SR12 is a receiver compliant with the ANT protocol, designed to output 12 PWM channel signals. It features dual antennas for enhanced reception and supports two-way transmission, transfer-back, and BVD (Battery Voltage Detection) functions. Its compact design makes it adaptable for a wide variety of models.

FlySky FS-SR12 receiver with product name overlay
Figure 1: FlySky FS-SR12 Receiver Overview

2. Setup

2.1 Receiver Overview

The FS-SR12 receiver features various ports and indicators for connection and operation. Familiarize yourself with the layout before installation.

FlySky FS-SR12 receiver, included manual, and wiring harness
Figure 2: FS-SR12 Receiver with Manual and Accessories
Close-up view of the FlySky FS-SR12 receiver showing the port labels
Figure 3: Close-up of FS-SR12 Receiver Ports and Labels

Receiver Port Definitions:

No.LabelDescription
1CH1/PPMChannel 1 / PPM Output
2-9CH2-CH9Channel 2 to Channel 9 Interfaces
10-12CH10-CH12Channel 10 to Channel 12 Interfaces
13BIND/VCCBinding / Voltage Input Interface
14BVD/VCCBattery Voltage Detection / Voltage Input Interface
15SENSSensor Interface
16SERVO/S.BUSServo / S.BUS Interface
17-(Power cathode)Negative Power Terminal
18+(Power anode)Positive Power Terminal
19S (Signal pin)Signal Pin for Channels
20LEDStatus Indicator Light
21AntennasDual Antennas for Signal Reception
22BIND buttonBinding Activation Button
23BVD harnessHarness for Battery Voltage Detection
24To connect battery anodeConnection Point for Battery Positive
25To connect battery cathodeConnection Point for Battery Negative

Note: BVD voltage detection range: 0~70V.

2.2 Binding

The FS-SR12 receiver supports both two-way and one-way binding. Two-way binding allows the transmitter to display information returned from the receiver.

2.2.1 Two-Way Binding Procedure

  1. Transmitter Setup: At the transmitter side, set the RF standard to 2WAY and then put the transmitter into bind mode.
  2. Receiver Bind Mode: The receiver supports three methods to enter bind mode:
    • BIND Button Binding: Press and hold the BIND button on the receiver while powering it on. The receiver's LED will flash, indicating bind mode. Release the BIND button.
    • Bind Cable Binding: Insert the bind cable into the BIND interface of the receiver, then power on the receiver. The LED will flash, indicating bind mode. Note: Remove the bind cable after successful binding.
    • BIND Button Binding After Power-on: If the receiver is powered on and not connected to the transmitter, press and hold the BIND button for 3 seconds. The LED will flash, indicating bind mode. Release the BIND button.
  3. Binding Confirmation: The receiver's LED will turn solid ON after successful binding. The transmitter will automatically exit bind mode.
  4. Verification: Check that the transmitter and receiver functions are working correctly. If any issues arise, repeat steps 1-3.

2.2.2 One-Way Binding Procedure

  1. Transmitter Setup: At the transmitter side, set the RF standard to 1WAY and then put the transmitter into bind mode.
  2. Receiver Bind Mode: Put the receiver into bind mode using one of the methods described in Section 2.2.1.
  3. Binding Confirmation: When the receiver's LED starts slow flashing, the binding process is complete. Manually exit bind mode on the transmitter. The receiver's LED will then turn solid ON, indicating successful binding.
  4. Verification: Check that the transmitter and receiver functions are working correctly. If any issues arise, repeat steps 1-3.

3. Operating

3.1 Failsafe Function

The failsafe function is designed to protect your model and personnel by outputting channel values according to user-defined settings when the receiver loses signal and becomes uncontrolled.

The FS-SR12 receiver supports two failsafe modes:

  • OFF: No output for the i-BUS/PPM/PWM interfaces.
  • ON: Outputs the failsafe values set for the i-BUS/PPM/PWM interfaces.

Important Notes on Failsafe:

  • For S.BUS signals, failsafe information is transmitted via failsafe flag bits, allowing subsequent devices to respond accordingly.
  • For PWM/PPM/i-BUS signals without failsafe flag bits, setting the output signal to OFF in case of failsafe transmits the failsafe information to subsequent devices.

4. Maintenance

4.1 Firmware Update

The firmware of the FS-SR12 receiver can be updated using the FlyskyAssistant software (version 3.0 or above), available on the Flysky official website (www.flyskytech.com).

There are two methods to update the receiver firmware:

  1. Update via Bound Transmitter:
    1. Bind the receiver to the transmitter (receiver LED solid ON).
    2. Connect the transmitter to your computer.
    3. Open FlyskyAssistant on the computer and proceed with the firmware update.
  2. Forced Update Mode:
    1. Connect the signal pin of the BIND interface to the signal pin of the CH11 interface on the receiver.
    2. Power on the receiver while pressing and holding the BIND button for more than ten seconds, until the receiver's LED repeatedly flashes three times then turns off once. Release the BIND button.
    3. Alternatively, power on the receiver first, then press and hold the BIND button for more than ten seconds until the LED repeatedly flashes three times then turns off once. Release the BIND button.
    4. After entering forced update mode, connect the transmitter to your computer and open FlyskyAssistant to update the firmware.

5. Troubleshooting and Attentions

To ensure safe and proper operation, please observe the following:

  • Always ensure the product is installed and calibrated correctly. Incorrect setup can lead to serious injury or damage.
  • Before turning off the transmitter, always disconnect the receiver's battery. Failure to do so can result in loss of control. Unreasonable failsafe settings can also cause accidents.
  • Mount the receiver away from motors, electronic speed controllers (ESCs), or any other device that emits excessive electrical noise.
  • Keep the receiver's antennas at least 1cm away from conductive materials such as carbon fiber or metal to prevent signal interference.
  • Do not power on the receiver during the setup process to avoid accidental control loss.

6. Specifications

Detailed technical specifications for the FlySky FS-SR12 receiver are provided below:

FlySky FS-SR12 receiver with detailed specifications listed next to it
Figure 4: FS-SR12 Receiver and Specifications
FeatureSpecification
Product NameFS-SR12
Compatible TransmittersAdapts transmitters with ANT protocol (e.g., FS-ST8)
Compatible ModelsFixed-wing aircraft, helicopters, gliders, delta-wing airplanes, multicopters, engineering vehicles, boats, robots, cars
PWM Channels12
RF2.4GHz ISM
Maximum Power<20dBm (e.i.r.p.) (EU)
2.4G ProtocolANT
Resolution4096
AntennaTwo antennas
Distance>1500m (Air distance without interference)
Input Power3.5~9V/DC
Working Current70mA/5V
Data OutputPWM/PPM/i-BUS/S.BUS
Online UpdateYes
Temperature Range-10°C ~ +60°C
Humidity Range20% ~ 95%
Dimensions44.8*32*11.3mm
Weight13g
CertificationsCE, FCC ID: 2A2UNSR1200

7. User Tips

No specific user tips were available from provided reviews or Q&A content for this product.

8. Certifications and Safety Information

8.1 FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

8.2 EU DOC Declaration

Hereby, Flysky Technology Co., Ltd. declares that the Radio Equipment [FS-SR12] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at www.flyskytech.com/info_detail/10.html.

8.3 RF Exposure Compliance

The distance between user and products should be no less than 20cm.

8.4 Environmentally Friendly Disposal

Old electrical appliances must not be disposed of together with residual waste, but must be disposed of separately. Disposal at communal collecting points via private persons is free. The owner of old appliances is responsible for bringing them to these collecting points or similar collection points. With this little personal effort, you contribute to recycling valuable raw materials and the treatment of toxic substances.

9. Warranty and Support

For support, warranty information, or further inquiries, please contact the manufacturer:

  • Manufacturer: ShenZhen FLYSKY Technology Co.,Ltd
  • Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China
  • Website: http://www.flysky-cn.com
  • Copyright: ©2022 Flysky Technology co., ltd

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.