EPEVER IPower-Plus Series

Contents

EPEVER IPower-Plus Series Pure Sine Wave Inverter User Manual

Model: IPower-Plus Series (IP2000-12-Plus(T), IP2000-22-Plus(T), IP2000-42-Plus(T))

1. Overview

The EPEVER IPower-Plus Series is a high-frequency pure sine wave inverter designed to convert 12/24/48VDC to 220/230V AC (or 110/120V AC) for various AC loads. It is engineered to international standards, ensuring high quality, reliability, and safety. This series is compatible with lithium-ion batteries and suitable for applications in RVs, boats, and residential settings requiring high-quality electrical power.

Key Features:

  • Pure sine wave output
  • Input to output electrical isolation
  • Digital dual closed-loop control of voltage and current
  • Input surge current suppression for lithium battery systems
  • Output power factor up to 1
  • Simple system wiring and 180 degrees rotating LCD
  • Comprehensive Protection: Reverse polarity, Low-voltage, Over-voltage, Output Protection, Overload, Short circuit, Overheating
  • Phone and PC remote control through RS485 port
  • Extra external switch port
  • Safety (EN/IEC62109) and EMC approved by international standards
EPEVER IPower-Plus Series Inverter Features
Overview and Features of the IPower-Plus Series Pure Sine Wave Inverter.

2. Setup and Installation

Before installation, ensure all components are present and undamaged. Choose a well-ventilated, dry location away from direct sunlight and heat sources. Mount the inverter securely.

2.1 System Wiring Diagram

The following diagram illustrates a typical solar power system setup including the IPower-Plus inverter. Ensure all connections are secure and follow local electrical codes.

Solar Power System Wiring Diagram
Wiring diagram for a solar power system including solar panels, charge controller, batteries, pure sine wave inverter, and AC loads. Shows connections for breakers, SPD, fuse, and remote meter.

2.2 Connection Steps:

  1. Battery Connection: Connect the inverter's DC input terminals to your battery bank. Ensure correct polarity (positive to positive, negative to negative). Use appropriate fuses or breakers between the battery and inverter.
  2. AC Output Connection: Connect your AC loads to the inverter's AC output sockets or terminal block, depending on your model. Refer to the image below for different socket types.
  3. Solar Panel & Charge Controller (Optional): If integrating with a solar system, connect solar panels to a charge controller, and the charge controller to the battery bank. The inverter draws power from the battery.
  4. Remote Meter/Monitoring (Optional): Connect the remote meter or PC monitoring interface via the RS485 port for advanced control and data logging.
  5. External Switch (Optional): Connect an external switch to the designated port for remote ON/OFF control.
Inverter AC Output Socket Types
Rear panel views of the inverter showing different AC output socket types: Universal, Australia/New Zealand, European, and Terminal (for IP1000 and above models).

2.3 Initial Power-Up:

After all connections are made and verified, switch on the DC breaker/fuse from the battery bank. Then, press the power button on the inverter. The LCD display will illuminate, showing operational status.

3. Operating Instructions

The IPower-Plus inverter features an intuitive LCD display and control buttons for easy operation and monitoring.

3.1 LCD Display and Buttons:

Inverter Front Panel with Display
Front view of the EPEVER IPower-Plus Series Pure Sine Wave Inverter, showing the display and control buttons.

The LCD provides real-time information such as input voltage, output voltage, output power, and error codes. Use the buttons to navigate through menus and adjust settings as needed. The display can rotate 180 degrees for flexible viewing.

3.2 Powering On/Off:

  • To Power On: Ensure DC input is connected. Press and hold the 'ON/OFF' button until the display lights up.
  • To Power Off: Disconnect all AC loads. Press and hold the 'ON/OFF' button until the display turns off. Then, disconnect the DC input from the battery.

3.3 Remote Monitoring:

The inverter supports remote monitoring and control via an RS485 port. Connect to a PC or a compatible remote display unit to access detailed performance data and adjust parameters.

4. Maintenance

Regular maintenance ensures optimal performance and longevity of your inverter.

  • Cleaning: Periodically clean the inverter's exterior and ventilation openings to prevent dust buildup, which can hinder cooling. Use a dry, soft cloth.
  • Connections: Annually check all electrical connections (DC input, AC output, ground) for tightness and corrosion. Tighten any loose connections.
  • Environment: Ensure the installation environment remains dry, well-ventilated, and within the specified operating temperature range.
  • Battery Health: Monitor your battery bank's health, as it directly impacts inverter performance.

5. Troubleshooting

This section provides solutions for common issues. For complex problems, contact technical support.

ProblemPossible CauseSolution
Inverter does not turn onNo DC input power; Loose battery connection; Blown fuse/tripped breakerCheck battery voltage; Verify all DC connections; Replace fuse or reset breaker.
No AC outputOverload; Short circuit; Low battery voltage; OverheatingReduce AC load; Check for short circuits in AC wiring; Charge batteries; Allow inverter to cool down.
Inverter beeps continuouslyLow battery voltage alarm; Overload alarmCharge batteries or reduce load; Reduce AC load.
Abnormal noise from inverterLoose components; Fan malfunctionPower off and check for loose parts (if safe); Contact support if fan is faulty.

6. Technical Specifications

Below are the detailed technical specifications for the EPEVER IPower-Plus Series inverters.

Technical Specifications Table for IP2000-Plus Models
Technical Specifications table for IP2000-12/22/32/42-Plus models.
Technical Specifications Table for IP500-Plus, IP1000-Plus, IP1500-Plus Models
Technical Specifications table for IP500-12/22-Plus, IP1000-12/22/32/42-Plus, IP1500-12/22/32/42-Plus models.
ParameterValue
Continuous Output Power2000W (for IP2000 models)
Rated Input Voltage12VDC, 24VDC, or 48VDC (model dependent)
Output Voltage220VAC (±3%) / 230VAC (±2%) or 110VAC / 120VAC
Output Frequency50/60Hz ±0.2%
Output WavePure Sine Wave
EnclosureIP20
CertificationCE
OriginMainland China

7. User Tips

  • For optimal performance, ensure your battery bank is adequately sized for your inverter's continuous output and peak surge requirements.
  • When connecting to sensitive electronics, always verify the inverter's pure sine wave output to prevent damage.
  • Utilize the remote monitoring features (RS485 port) to keep track of your system's performance and battery status, especially in off-grid or remote installations.
  • Always disconnect the AC loads before powering off the inverter to prevent sudden power interruptions to your devices.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official EPEVER website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.