1. Introduction
Thank you for purchasing the SucceBuy Ultrasonic Cleaner. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before use and retain it for future reference.
General Safety Cautions
- Ensure the power supply is within the rated range before connecting the power cable. Refitting is strictly prohibited. The control panel may be eroded by organic solutions, strong acids, and strong alkalis.
- Ensure the earth wiring is well connected before starting.
- Ensure the power key or knob is in the 'OFF' position before starting.
- Do not operate if the tank is empty, as the ultrasonic generator may be damaged. If heating is needed, the water level should not be less than 2/3 of the tank capacity.
- Please close the lid to reduce noise and pay attention to water and steam to avoid burning skin when opening the lid.
- Do not relocate the machine when fluid is in the tank to prevent overflow.
- Only use water-soluble liquids suitable for benchtop ultrasonic cleaners. Strong acid or flammable cleaners are forbidden.
- Do not use the machine in severe environments such as:
- Places where temperature changes fiercely.
- Places where humidity is too high and is prone to condensation.
- Places where vibration or impact is strong.
- Places where corrosive gas or dust exists.
- Places where water, oil, or chemicals may splash.
- Places filled with explosive and flammable gas.
- Shorten the daily working time. It is suggested to stop for a few minutes for heat dissipation after working over 30 minutes.
Important Note: Heater is forbidden when using flammable liquid (such as alcohol, solvent cleaner etc.) to clean objects. Cleaning effect will be much better if using the machine together with proper solvent.
2. Product Overview
The SucceBuy 15L Digital Ultrasonic Cleaner is designed for effective cleaning of various items using advanced ultrasonic technology.
Components and Features
Control Panel
Dimensions and Capacity
Advanced Technology
Construction Details
3. Technical Specifications
| Feature | Specification |
|---|---|
| Tank Material | Stainless Steel SUS304 |
| Heating Power | 400W |
| Ultrasonic Power | 360W |
| Frequency | 40kHz |
| Power Supply | AC110V/60Hz |
| Tank Capacity | 13.5-15L (Actual volume may be smaller due to curved bottom) |
| Time Setting | 0 - 30 minutes (LED Digital Display) |
| Temperature Setting | RT-176℉ / RT-80℃ |
| Transducer Quantity | 6 sets |
| Tank Size (L x W x H) | 13 x 11.8 x 5.9 in / 330 x 300 x 150 mm |
| Product Size (L x W x H) | 14 x 12.8 x 11.4 in / 355 x 325 x 290 mm |
| Product Weight | 9.72 kg / 21.4 lbs |
| Certification | CE |
4. Setup
- Unpack the unit and ensure all components are present and undamaged.
- Place the unit on a stable, flat working platform in a dry and cool environment.
- Ensure the earth wiring is properly connected.
- Add water or appropriate cleaning solution to the tank. The water level should be above 2/3 of the tank capacity but not overflowing.
- Connect the power cable to a grounded outlet.
Note: Ensure the unit is placed on a stable, flat surface in a dry and cool environment.
5. Operation Instructions
Digital Model Operation
- Power On: Ensure the power key is in the 'OFF' position. Connect the unit to power. The default time setting is "05:00".
- Time Setting: Press the 'TIME+' button to increase the cleaning time by 1 minute per press. Press the 'TIME-' button to decrease the cleaning time by 1 minute per press. The time range is 0-30 minutes.
- Temperature Setting (Heating): The default temperature setting is "50°C" and the actual temperature is displayed. Press 'TEMP+' to increase the temperature by 1°C per press. Press 'TEMP-' to decrease the temperature by 1°C per press. If the set temperature is lower than the actual tank temperature, the heating operation will stop automatically. The heating function is optional.
- Start Cleaning: After setting the desired time and temperature, press the 'ON/OFF' button (for time function) once to start the ultrasonic cleaning. The equipment will work automatically.
- Stop Cleaning: Press the 'ON/OFF' button (for time function) again to stop the work process.
- Power Off: Switch off the unit and disconnect the power supply.
Adjusting Power
This function is only available for power adjustable models. Rotate the power knob clockwise SLOWLY to increase the power from 40% to 100%, and counter-clockwise SLOWLY to decrease sonic power.
6. Maintenance
- The unit must be opened by authorized specialized personnel only for maintenance and care.
- Clean the contaminant in the tank frequently.
- After use, empty out the liquid and clean the tank and the unit with a clean cloth for next use.
7. Troubleshooting
| No. | Problem | Possible Causes | Solutions |
|---|---|---|---|
| 1 | No ultrasonic | A. Power supply not connected B. Fuse broken C. Cable short circuit D. Transducer short circuit E. PCB Board broken F. Other reasons | A. Check and plug power switch. B. Check the fitted power supply and change the same specification fuse. C. Connect fitted cable or replace a new. D. Inquiry our after service engineer. E. Check the broken part and change it. F. Inquiry our after service engineer. |
| 2 | Time control failure | A. Timer knob out of control B. Timer failure C. Other reasons | A. Loosen or tighten the screw. B. Replace timer or digital panel. C. Inquiry our after service engineer. |
| 3 | No heating | A. Heater power switch bad linkage B. Fuse burn out C. Heating pad burn out D. Digital display board out of control E. Other reasons | A. Check heating plug and connect well, Check outlet line with multimeter: if OK and resistance value is few hundred OHMS. B. Change the same specification fuse. C. Replace the bad heating pad if open circuit. D. Check the broken part and change it. E. Inquiry our after service engineer. |
| 4 | Temperature control failure | A. Thermostat loosen B. Thermostat tube broken C. Digital display out of control D. Other reasons | A. Fasten the thermostat header. B. Replace thermostat. C. Check the broken part and change it. D. Inquiry our after service engineer. |
| 5 | Not well cleaning | A. Not strong ultrasonic cleaning B. Too high too low liquid surface C. Too high too low temperature D. Not suitable cleaning liquid E. Other reasons | A. Connect ultrasonic button and adjust. B. Adjust liquid into the best surface. C. Adjust temperature into the most fitted. D. Stop and switch off power supply, replace suitable liquid after the previous liquid cool down. E. Inquiry our after service engineer. |
| 6 | Electric leakage | A. Customer side not grounded B. Machine not grounded | A. To ensure grounded. B. Check if machine earth wire loosen. |
8. Applications
The ultrasonic cleaner is suitable for a wide range of applications, both professional and household.
Typical Items and Industries
- Electronic Factory: PCB, integrated circuits, power tubes, silicon wafers, diodes, lead frames, capillaries, trays.
- Car Workshops: Engine parts, fuel injectors, small components.
- Industrial and Mining Area: Industrial parts, tools, small machinery components.
- Laboratories: Lab instruments, glassware, optical devices, filters.
- Hospitals & Dental Clinics: Medical instruments, dental tools, dentures.
- Watch Shops: Watches, watch parts, jewelry.
- Optical Shops: Eyeglasses, optical lenses, contact lens accessories.
- Jewelry Shops: Jewelry, rings, necklaces, bracelets, diamonds.
- Mobile Phone Repair Shops: Small electronic components, circuit boards.
- Household Use: Cutlery, combs, toothbrushes, coins, small household items.
9. User Tips
For optimal cleaning results, always use appropriate cleaning solutions for the items being cleaned. Ensure items are fully submerged but not overcrowded in the cleaning basket. Regularly check the water level and replace the cleaning solution as needed for consistent performance.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official product documentation or contact the manufacturer's customer service.
A detailed user manual is available in PDF format: Download User Manual (PDF)
