ThinkRider XXPRO Direct Drive Smart Bike Trainer

1. Product Introduction

Thank you for purchasing the ThinkRider XX PRO smart Bike Trainer. Please read the instruction carefully before use.

2. Package Contents

The ThinkRider XXPRO Smart Bike Trainer package includes the following items:

• XX PRO Smart Bike Trainer (1 unit)
• Power Adapter (1 unit)
• 8-9-10 Speed Flywheel Washer (1 unit)
• Quick Release Adapters (Support 130/135mm)
• Thru Axle Adapters (Support 142/148mm)
• Base Screws (5 units)
• 17mm Wrench
• Cassette Adjustment Spacer (4 units)
• Hex Wrench

Special Note:

The standard accessories do not include the cassette, Thru axle release and Quick release, BLE and ANT+ USB receiver. If you need these, you can buy them separately from your dealer.

Detailed Package Contents

3. Technical Specifications

Adaptation Instructions

• Rim Size: Road bike: 24"/650c/700c, MTB: 24"/26"/650B/29"
• Hub Type: 130/135QR (Standard), 12x142 and 12x148 thru axle
• Cassette: Shimano HG specification, compatible with Shimano 8-12-speed cassettes, and SRAM 8-11-speed cassettes (XDR or CP freehub body sold separately).
• Compatible Cycling Software: The standard protocol is compatible with most cycling software on the market, such as Zwift, Onelap, Kinomap, BKOOL Cycling, Rouvy.

Product Specifications Overview

4. Setup

4.1 General Installation

1. Place the trainer on a level surface, ensuring there are no obstacles or dangerous objects around.
2. Install the base and tighten the screws to make sure the trainer is stable.
3. Connect the trainer to a standard 110V-220V power outlet with the original power adapter.

4.2 Cassette Installation

The trainer comes with a standard freehub body, compatible with Shimano HG 8-12-speed cassettes, as well as SRAM 8-11-speed road and mountain bike cassettes.

• 11-speed standard cassettes can be installed directly.
• 8-10-speed cassettes require a spacer. Please consult customer service for details if needed.
• Campagnolo or SRAM XDR freehub bodies must be purchased separately.

Cassette Installation Diagram

Note: The left side of the leveling foot is short, while the right side (drive side) is longer.

4.3 Adapter Installation

The non-drive side adapter can be inserted in different directions to suit various axle spacing sizes.

130-135 Quick Release Adapter Installation

• For 130mm quick release: Ensure the short end of the adapter is exposed.
• For 135mm quick release: Ensure the long end of the adapter is exposed.
• Remember to install the quick release adapter.

Quick Release Adapter Configuration

142-148 Thru Axle Adapter Installation

• For 142mm thru axle: Ensure the short end of the adapter is exposed.
• For 148mm thru axle: Ensure the long end of the adapter is exposed.
• Remember to install the quick release adapter.

Thru Axle Adapter Configuration

5. Operating Instructions

5.1 Safety Precautions

• Always install and use the trainer on a flat and sturdy surface.
• Before each use, carefully check that your quick-release lever or thru-axle is securely locked to the frame to prevent loosening, which could cause personal injury and property damage.
• Do not touch the moving parts of the trainer with your hands or any objects.
• After long-term use, the trainer's freewheel may become hot; do not touch it.
• During cycling, keep children and pets away from the trainer.
• Do not touch the freewheel or disassemble the bicycle while the inertia flywheel is still spinning.
• During use, keep the trainer away from fire sources, water sources, and other obstacles.
• Do not stand on the trainer while pedaling; avoid excessive rocking; pay attention to safety.
• Users with cardiovascular and cerebrovascular diseases or other conditions unsuitable for high-intensity exercise are strictly prohibited from using the trainer.
• Consult a doctor before starting or modifying any exercise training plan.
• Individuals who are not capable of responsible behavior should not use the trainer.

5.2 Software Connection and Firmware Update

The ThinkRider XXPRO is compatible with most cycling software on the market, such as Zwift, Trainerroad, Rouvy, Onelap, Kinomap, BKOOL Cycling, Garmin, Wahoo, and iGPSPORT.

1. Download and install your preferred cycling software on your mobile phone or computer.
2. Power on the trainer.
3. Open the cycling software, navigate to the device connection interface, search for the "cycling trainer" signal, and connect.

The cycling trainer can be firmware upgraded. For firmware updates, please download the app on your mobile phone: thinkrider tools.

Important: During the upgrade, keep the phone within 1 meter of the cycling trainer. Do not exit the upgrading interface, do not carry out any other operation, and do not turn off the power of the cycling trainer until the firmware upgrade is completed.

For a visual guide on installation and software setup, you can refer to the official video: https://youtu.be/5TqY8dbD5YE

6. Maintenance

• Keep the trainer clean and dry. Wipe down after each use to prevent sweat corrosion.
• Regularly inspect all screws and connections to ensure they are tight and secure.
• Avoid exposing the trainer to excessive moisture or direct water contact to prevent equipment failure.
• When transporting or storing the trainer, use the original packing materials to protect it from damage.
• Periodically check for any signs of wear and tear on moving parts and cables.

7. Troubleshooting

7.1 Connectivity Issues

• The trainer cannot connect to a cycling app and a bike computer at the same time, as this may cause data output and resistance to malfunction.
• If your smart trainer cannot be found by the app, it may be due to:
  • The same smart trainer cannot be connected to two apps simultaneously.
  • If the smart trainer is already connected to an app (a solid red light indicates it is connected), the next app will not be able to find the smart trainer.

  Solution: First, check and disconnect any previous connection (or unplug and restart the trainer; a flashing red light indicates a waiting connection state), and then proceed with the next app connection.

8. User Tips

• Single App Connection: To ensure optimal performance and accurate data, always ensure only one application (either a cycling app or a bike computer) is actively connected to your ThinkRider XXPRO trainer at any given time. Simultaneous connections can lead to data inaccuracies and resistance control issues.
• Unplugged Riding: The XXPRO features enhanced self-power generation, allowing for an authentic riding experience even when unplugged. This is particularly useful for flexible placement without needing a power outlet nearby.
• Quiet Operation: The direct drive system and brushless motor ensure quiet operation, making it suitable for indoor use without disturbing others.

9. Warranty

• The product is guaranteed for one year. If the product fails during the warranty period due to original device quality problems or assembly process, the company will provide free maintenance and spare parts replacement.
• Please use the original packing materials when you need to ship the package for service.
• Product damage or malfunction caused by the following reasons is not covered by the warranty:
  • Damage caused by use or installation not in accordance with the instructions.
  • Product damage caused by human factors or accidents.
  • Unauthorized disassembly of the product without contacting the company or dealer.
  • Ingress of water causing equipment failure.
  • Aging and scratches caused by normal use.
• After the expiration of the warranty period, the company will still provide maintenance services, but the corresponding maintenance costs will be charged.

10. Support

If you have any after-sales questions or require technical assistance, please contact our engineers:

Email: service2@thinkrider.com

Wuxi ThinkRider Technology Co.,Ltd.
Website: www.thinkrider.com