EPEVER Tracer3210AN G3

Contents

EPEVER Tracer3210AN G3 MPPT Solar Charge Controller User Manual

Model: Tracer3210AN G3 | Brand: EPEVER

1. Introduction and Overview

The EPEVER Tracer-AN G3 series represents a new generation of MPPT (Maximum Power Point Tracking) solar charge/discharge controllers. This controller is designed to maximize the utilization of photovoltaic (PV) power and extend battery life through an adaptive 3-stage charging mode. It features a constant voltage output function, ensuring broad compatibility, especially with various lithium batteries. Under specific conditions, the PV system can directly power loads without requiring a battery. Its efficient design minimizes standby power consumption, contributing to extended system standby time. This series is well-suited for diverse applications, including RVs, residential solar systems, and outdoor monitoring setups.

EPEVER Tracer3210AN G3 MPPT Solar Charge Controller with WiFi module

Figure 1: EPEVER Tracer3210AN G3 MPPT Solar Charge Controller with WiFi module.

2. Key Features

Overview and Features of the EPEVER Tracer-AN G3 series MPPT Solar Charge Controller

Figure 2: Overview and Features of the EPEVER Tracer-AN G3 series.

  • Constant voltage output function.
  • Maximum DC/DC conversion efficiency of 98%.
  • Advanced MPPT technology, with a maximum tracking efficiency higher than 99.5%.
  • Supports multiple battery types, including lithium batteries.
  • Features battery temperature compensation and stable self-activation function.
  • Equipped with an LCD screen for convenient battery parameter setting.
  • Comprehensive electronic protection mechanisms.
  • Low self-consumption, typically less than 10mA.
  • Multiple load work modes for versatile application.
  • Parameter setting capabilities via PC software, mobile application, or remote meter.
  • RS485 communication interface with optional 4G or Wi-Fi modules for enhanced connectivity.

3. Specifications

Technical Specifications table for Tracer-AN G3 series controllers, including Tracer3210AN G3

Figure 3: Technical Specifications for Tracer-AN G3 series controllers.

ParameterTracer3210AN G3
Battery Rated Voltage12/24VDC Auto-recognition
Rated Charging Current30A
Rated Discharge Current30A
Controller Work Voltage Range8-31V
PV Max. Open-circuit Voltage100V (92V at 25°C)
MPPT Voltage Range(Battery voltage + 2V) - 72V
Rated Charging Power390W/12V, 780W/24V
Static Losses<8mA(12V), <5mA(24V)
Discharge-circuit Voltage Drop<0.23V
Temperature Compensation-3mV/°C/2V (Default)
Grounding TypeCommon negative
RS485 Port5VDC/200mA(RJ45)
LCD Backlight TimeDefault:60S, Range:0-999S (0 seconds: the backlight is ON all time)
Work Temperature Range-25°C ~ +45°C (100% loads working)
Storage Temperature Range-20°C ~ +70°C
Relative Humidity< 95% (N.C.)
EnclosureIP30
Dimension (L x W x H)228x164x55 mm
Mounting Size (L x W)170x155 mm
Mounting Hole SizeΦ5mm
Terminal10AWG (6mm²)
Recommended Wire Size10AWG (6mm²)
Net Weight1.26kg

4. Setup and Installation

Proper installation is crucial for the safe and efficient operation of your solar charge controller. It is recommended that installation be performed by qualified personnel, especially for complex systems. Always ensure all power sources are disconnected before making any connections.

4.1 Component Identification

Detailed view of the EPEVER Tracer charge controller showing LCD display, buttons, and terminal connections

Figure 4: EPEVER Tracer3210AN G3 Component Layout.

  • LCD Display: Shows system status and parameters.
  • SELECT Button: Used to navigate menus and select options.
  • ENTER Button: Used to confirm selections and enter settings.
  • Mounting Holes (Φ5): For securing the controller to a surface.
  • Remote Temp. Sensor Terminal: Connects to an external temperature sensor for accurate battery temperature compensation.
  • Solar Panel Terminal: Connects to the photovoltaic (PV) array.
  • Battery Terminal: Connects to the battery bank.
  • Load Terminal: Connects to the DC loads.
  • COM (RJ45) Port: For communication with PC software, APP (via WiFi/Bluetooth module), or remote meter.

4.2 Wiring Diagram and Connection Order

Follow the wiring diagram carefully. Connect components in the specified order to prevent damage to the controller or other system components. Ensure correct polarity for all connections.

Wiring diagram for a solar charge controller system including PV, controller, battery, DC load, MT75, iPower-Plus, and AC load

Figure 5: Typical Solar System Wiring Diagram.

  1. Connect the Battery: First, connect the battery to the controller's battery terminals. Ensure correct polarity (positive to positive, negative to negative). The controller will detect the battery voltage.
  2. Connect the Solar Panel: Next, connect the solar panel(s) to the controller's PV terminals. Again, observe correct polarity.
  3. Connect the DC Load: Finally, connect your DC loads to the load terminals.
  4. Optional Connections: Connect the remote temperature sensor to its dedicated terminal. If using a remote meter (e.g., MT75) or a WiFi/Bluetooth module, connect it to the RJ45 COM port.

Important: Always connect the battery first and disconnect the battery last. This sequence prevents potential damage from voltage surges.

Diagram illustrating a typical household solar power system with the EPEVER charge controller

Figure 6: Example of a household solar power system setup.

5. Operating Instructions

The Tracer3210AN G3 controller manages the charging process and load output. Use the LCD display and buttons to monitor system status and adjust settings.

5.1 Charging Stages

Diagram showing Bulk, Absorption, Float 3-stage charging with auto switch or manual control

Figure 7: 3-Stage Battery Charging Process.

The controller employs an adaptive 3-stage charging algorithm to optimize battery health and lifespan:

  • Bulk Charging: Delivers maximum current to rapidly charge the battery until it reaches a set voltage.
  • Absorption Charging: Maintains a constant voltage, gradually reducing current as the battery approaches full charge.
  • Float Charging: Reduces voltage to a lower level to maintain the battery at full charge, compensating for self-discharge.
Image showing the maximum charging current range (1A to Rated Value) and its benefit for battery lifespan

Figure 8: Max Charging Current and Battery Lifespan.

5.2 Load Control Modes

EPEVER Tracer MPPT Solar Charge Controller with display showing load control modes and extensive protections

Figure 9: Multiple Load Control Modes.

The controller offers several load control modes to manage the DC output:

  • Manual: Load output is controlled manually via the controller's buttons or connected remote devices.
  • Dusk to Dawn with Timer: Automatically turns on the load at dusk and turns it off after a set duration.
  • Timer: Allows setting exact ON and OFF times for the load.
  • Dust to Dawn: Automatically turns on the load at dusk and turns it off at dawn by detecting PV voltage.

Refer to the full product manual for detailed instructions on configuring these modes via the LCD or communication interfaces.

5.3 Battery Type Support

Diagram illustrating support for multiple battery types (Flooded, Lithium, Gel, Sealed, Customized) and 99.5% tracking efficiency with an MPPT curve

Figure 10: Multiple Battery Type Support and MPPT Efficiency.

The Tracer3210AN G3 supports various battery types, including Flooded, Lithium, Gel, Sealed, and customizable options. Ensure the correct battery type is selected in the controller settings for optimal charging and protection.

6. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your solar charge controller.

  • Cleanliness: Keep the controller clean and free from dust and debris. Use a dry cloth for cleaning.
  • Connections: Periodically check all wiring connections for tightness and corrosion. Loose connections can lead to power loss or overheating.
  • Ventilation: Ensure the controller has adequate ventilation and that its cooling fins are not obstructed.
  • Monitoring: Regularly monitor the system's performance via the LCD display or connected monitoring tools (PC software, APP). Look for any unusual readings or error codes.
  • Battery Health: Monitor battery voltage and health. Ensure the battery type setting in the controller matches your installed battery.

7. Troubleshooting

The Tracer3210AN G3 controller incorporates extensive electronic protections to safeguard itself and the connected system components. If you encounter issues, check the following common problems and the controller's protection indicators.

EPEVER Tracer MPPT Solar Charge Controller with display showing load control modes and extensive protections

Figure 11: Extensive Protections Integrated.

7.1 Integrated Protections

  • Low Voltage Protection
  • Over Temperature Protection
  • Over Load Protection
  • Over Discharge Protection
  • Over Voltage Protection
  • Overcurrent Protection
  • Short Circuit Protection
  • Reverse Current Protection

If the controller enters a protection state, it will typically display an error code or indicator on the LCD. Consult the comprehensive manual for a detailed list of error codes and their corresponding troubleshooting steps. For issues not covered, contact EPEVER technical support.

8. User Tips

No specific user tips were available from provided reviews or Q&A content for this product.

9. Warranty and Support

The EPEVER Tracer3210AN G3 MPPT Solar Charge Controller is manufactured by EPEVER, a brand known for its solar power solutions. This product is CE certified, indicating compliance with European safety, health, and environmental protection requirements.

For detailed warranty information, technical support, or service inquiries, please refer to the official EPEVER website or contact your authorized dealer. Ensure you have your product model number (Tracer3210AN G3) and purchase details available when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.