MN MODEL 1:20 Drift Remote Control Car

Contents

Drift Remote Control Car Instruction Manual

Model: 1:20 Drift Remote Control Car

Brand: MN MODEL

1. Introduction

Thank you for purchasing the MN MODEL 1:20 Drift Remote Control Car. This high-performance RC car features full proportional steering, a gyroscope stabilization system, and upgraded LED lights for an immersive drifting experience. Please read this manual thoroughly before operating the vehicle to ensure safe and optimal performance.

2. Important Safety Information

  • WARNING: Not suitable for children under 36 months due to small parts.
  • Always operate the RC car in a safe, open area away from people, pets, and obstacles.
  • Do not operate near water or in wet conditions to prevent damage to electronic components.
  • Keep fingers, hair, and loose clothing away from moving parts (wheels, gears).
  • Do not touch the motor immediately after use, as it may be hot.
  • Use only the provided charging cable and battery. Improper charging can lead to fire or injury.
  • Adult supervision is recommended for younger users.

3. Package Contents

Please check the box to ensure all items are present:

  • 1x 1:20 Scale Drift Remote Control Car
  • 1x Remote Controller (2.4GHz)
  • 1x High-rate Lithium Battery (for car)
  • 1x USB Charging Cable
  • 4x Drift Tires (installed or spare set)
  • Spare Screws
  • Screwdriver
  • Roadblock Props
  • Operating Instructions (this manual)
Diagram showing the package contents including the RC car, remote, battery, USB cable, drift tires, screws, screwdriver, and roadblock props.
Figure 3.1: Package Contents and Car Dimensions (21cm x 9cm x 6cm)

4. Setup

4.1. Charging the Car Battery

  1. Connect the provided USB charging cable to the car's lithium battery.
  2. Plug the USB end into a standard USB power adapter (not included, e.g., phone charger, computer USB port).
  3. The indicator light on the USB cable will show charging status (e.g., red for charging, off/green for fully charged).
  4. Charging typically takes 1-2 hours. Do not overcharge.

4.2. Battery Installation (Car)

  1. Locate the battery compartment on the underside of the RC car.
  2. Open the compartment cover.
  3. Insert the fully charged lithium battery, ensuring correct polarity.
  4. Close the battery compartment cover securely.

4.3. Battery Installation (Remote Controller)

  1. Locate the battery compartment on the back of the remote controller.
  2. Open the compartment cover.
  3. Insert 2x AA batteries (not included), ensuring correct polarity.
  4. Close the battery compartment cover securely.

4.4. Remote Control Pairing

  1. Ensure the car's battery is installed and the car's power switch is OFF.
  2. Turn ON the remote controller using the 'ON/OFF' switch. The indicator light on the remote will blink.
  3. Turn ON the RC car's power switch.
  4. The remote controller's indicator light should become solid, indicating successful pairing.
  5. If pairing fails, turn off both devices and repeat the steps.
Diagram of the remote control with labels for Speed Adjustment, Steering Adjustment, Gyroscope Adjustment, Light Switching, Power Switch, Full Proportional Servo Steering, and Electronic Throttle Tuning.
Figure 4.1: Remote Control Layout and Functions

5. Operating Instructions

5.1. Basic Controls

  • Throttle Trigger: Pull the trigger to accelerate forward. Push the trigger to brake or reverse. The car features continuously variable transmission for precise speed control.
  • Steering Wheel: Turn the steering wheel left or right to control the car's direction. The full proportional servo steering provides responsive and accurate control.

5.2. Adjustments on Remote Controller (Refer to Figure 4.1)

  • TH.TRIM (Throttle Trim): Adjusts the neutral point of the throttle. If the car moves slightly forward or backward when the trigger is at neutral, use this knob to fine-tune it.
  • ST.TRIM (Steering Trim): Adjusts the neutral point of the steering. If the car veers left or right when the steering wheel is centered, use this knob to correct it.
  • ESP (Electronic Stability Program): This feature, also known as Vehicle Stability Control (VSC) or Gyroscopic Vehicle Self-Stabilization System (GUSS), helps maintain control during abnormal conditions like skidding or tire slippage. Adjust the knob to increase or decrease the level of stability assistance. Higher ESP provides more stability, lower ESP allows for more aggressive drifting.
  • LIGHT (Light Switching): Press this button to cycle through different LED light modes, including upgraded LED front/rear light synchronization and underglow linkage.
  • CH3: This button may control additional features if available on your specific model.

5.3. Drifting Techniques

The 1:20 Drift Remote Control Car is designed for high-speed drifting. Practice using the full proportional steering and throttle control to initiate and maintain drifts. Experiment with the ESP adjustment to find your preferred balance between stability and drift angle. The specialized drift tires are optimized for smooth slides.

Video 5.1: Product demonstration showcasing high-speed racing, U-drifts, and 360-degree drifts with LED underbody ambient lighting.

6. Maintenance

6.1. Cleaning

  • After each use, gently wipe the car body with a soft, dry cloth to remove dust and debris.
  • Avoid using water or chemical cleaners, as they can damage electronic components.
  • Use a small brush to clean dirt from the wheels and chassis.

6.2. Battery Care

  • Always disconnect the battery from the car when not in use.
  • Store batteries in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Do not leave batteries fully charged or fully discharged for extended periods. For long-term storage, charge them to about 50%.

6.3. Tire Maintenance

  • Inspect drift tires regularly for wear and tear. Replace them if they become excessively worn to maintain optimal drifting performance.
  • Ensure tires are free of debris that could affect performance.

6.4. Storage

  • Store the car and remote control in a dry, cool environment.
  • Remove batteries from both the car and remote if storing for an extended period.

7. Troubleshooting

  • Car not responding: Check if both the car and remote are powered on. Ensure batteries are charged and correctly installed. Re-pair the remote control.
  • Poor performance/short range: Ensure batteries are fully charged. Check for interference from other 2.4GHz devices.
  • Car veers to one side: Adjust the ST.TRIM knob on the remote control.
  • Car moves slightly at neutral throttle: Adjust the TH.TRIM knob on the remote control.
  • Lights not working: Check if the car is powered on and the LIGHT button on the remote has been pressed.

8. Specifications

FeatureDetail
Brand NameMN MODEL
Scale1:20
Remote Distance100M
Dimensions21cm x 9cm x 6cm
MaterialPlastic
Power SourceLithium Battery (Car)
State of AssemblyReady-to-Go
FeaturesRemote Control, LED Lights, Gyroscopic Stabilization
DesignCars
Recommend Age14+ years
OriginMainland China

9. User Tips

  • Practice Makes Perfect: Drifting takes practice. Start in a wide-open space to get a feel for the controls and the car's response.
  • Experiment with ESP: Adjust the ESP knob on the remote to find the perfect balance between stability and the thrill of drifting. Lower settings offer more challenge and control for experienced users.
  • Utilize Roadblock Props: Use the included roadblock props to create your own drift courses and challenge yourself.
  • Night Driving Fun: The upgraded LED lights and underbody ambient lighting make for an exciting experience in low-light conditions.

10. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please contact the seller or manufacturer directly with your purchase details. Keep your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.